VISUAL COMFORT KW 5525 User manual

Type
User manual

VISUAL COMFORT KW 5525 is a 12-inch disc pendant light fixture designed to enhance the ambiance of your living space. With its adjustable rods, you can customize the hanging height to suit your needs. It features a sleek canopy, rods, and shade in a stylish finish, adding a touch of sophistication to your décor. The fixture is compatible with LED bulbs, ensuring energy efficiency and long-lasting illumination. Installation requires basic electrical knowledge and tools, and the instruction manual provides clear step-by-step guidance for a successful setup.

VISUAL COMFORT KW 5525 is a 12-inch disc pendant light fixture designed to enhance the ambiance of your living space. With its adjustable rods, you can customize the hanging height to suit your needs. It features a sleek canopy, rods, and shade in a stylish finish, adding a touch of sophistication to your décor. The fixture is compatible with LED bulbs, ensuring energy efficiency and long-lasting illumination. Installation requires basic electrical knowledge and tools, and the instruction manual provides clear step-by-step guidance for a successful setup.

Pertica 12" Disc Pendant
Item # KW 5525
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
NOTICE:
1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (B) from canopy (H) by removing collar ring (I).
3. Install mounting plate (B) to the junction box and secure with
mounting screws (D).
4. Feed electrical wires through bottom rod (L) and thread to
fixture (M). Repeat for middle rod (K), connecting to bottom
rod (L).
5. Continue feeding wires through collar ring (I), canopy (H) and top
rod (J).
6. Holding fixture upright, slide collar ring (I), canopy (H) down rods and
rest on fixture (M). Then connect top rod (J) to middle rod (K).
NOTE: Slide components down slowly to avoid damages.
7. Hang fixture swivel ball (G) to center of mounting plate (B) and secure
with set screw (F) using provided screwdriver (E). See diagram 1.
8. Cut excess wires, being sure to leave enough to reach the junction
box. Separate wires, and strip insulation on each 5/8".
9. Wrap supply ground wire (usually green or bare copper) around the
green grounding screw (see diagram 2). Tighten.
NOTE: It is imperative that the fixture is grounded.
10. Connect fixture neutral wire (black) to driver (C) output wire (black)
using wire nut (A).
C
D
A
G
H
I
J
K
L
M
O
P
N
A
B
Phillips Screwdriver Slotted Screwdriver Wire Cutters
Wire Strippers Slip-joint pliers
Diagram 2
F
Diagram 1
E
G
Pertica 12" Disc Pendant
Item # KW 5525
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
11. Connect fixture hot wire (red) to driver (C) output wire (red) using wire
nut (A).
CAUTION: Do not reverse the hot and neutral connections.
12. Connect driver (C) input neutral wire (white) to the supply neutral wire
(usually white) using wire nut (A).
13. Connect driver (C) input hot wire (black) to the supply hot wire (usually
black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections.
14. Make sure all wire connections are tight, then carefully tuck into the
junction box.
15. Insert driver (C) into center of mounting plate (B).
16. Install canopy (H) to mounting plate (B) and secure with collar ring (I).
17. Remove protective cap (P) from fixture (M), then thread LED bulb (O)
to fixture (M).
18. Thread shade (N) to fixture (M).
NOTE: Do not over-tighten otherwise shade could become damaged.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents.
NOTICE:
C
D
A
G
H
I
J
K
L
M
O
P
N
A
B
Diagram 2
F
Diagram 1
E
G
Pertica 12" Disc Pendant
Item # KW 5525
UNPACKING NOTICE
Please follow instructions below to avoid possible damages caused by
improper removal.
NOTICE:
1. Open box and remove top layer of packaging.
2. Evenly lift shade in areas indicated by arrows (see diagram) until
clear of packaging. Place on clean, soft surface.
NOTE: Remove slowly to avoid damages.
  • Page 1 1
  • Page 2 2
  • Page 3 3

VISUAL COMFORT KW 5525 User manual

Type
User manual

VISUAL COMFORT KW 5525 is a 12-inch disc pendant light fixture designed to enhance the ambiance of your living space. With its adjustable rods, you can customize the hanging height to suit your needs. It features a sleek canopy, rods, and shade in a stylish finish, adding a touch of sophistication to your décor. The fixture is compatible with LED bulbs, ensuring energy efficiency and long-lasting illumination. Installation requires basic electrical knowledge and tools, and the instruction manual provides clear step-by-step guidance for a successful setup.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI