The Howard Miller 497270 is a curio display cabinet that allows you to showcase your收藏品and keepsakes behind glass doors. It features adjustable glass shelves, a wall safety strap for added security, and pre-installed pivot hinges for easy assembly. The cabinet also includes strike plates, nylon pads, and rubber washers for a secure fit.
The Howard Miller 497270 is a curio display cabinet that allows you to showcase your收藏品and keepsakes behind glass doors. It features adjustable glass shelves, a wall safety strap for added security, and pre-installed pivot hinges for easy assembly. The cabinet also includes strike plates, nylon pads, and rubber washers for a secure fit.
Hardware Parts List:
Pivot Hinge
Nylon Washer (white)
Pivot Hinge
Pin Hole
(2 top, 2 bottom)
Pivot Hinge
(Preinstalled)
Pivot Hinge
(Preinstalled)
Strike Plate
Figure A
Strike Plate
CURIO DISPLAY CABINET INSTRUCTIONS
FOR GLASS DOOR ASSEMBLY
CAUTION: Two people are required to
assemble the Glass Door Panels to the
cabinet. Use care when handling the
Glass Door Panels. To avoid bodily injury or
harm, assemble Glass Door Panels in an
area without children or other potential
hazards present.
1. Choose a location for the curio display cabinet. Refer to your cabinet
set-up instructions. Securely fasten the wall safety strap to the cabinet
and wall and install glass shelves prior to Glass Door Panel assembly.
2. Unpack the Glass Door Panels and set aside in a safe location.
3. Install a Nylon Washer (1) and Pivot Hinge (1) to the Pivot Hinge Pin Hole as shown at the bottom left and right of the
cabinet. Install the Pivot Hinges with the Set Screws facing the inside of the cabinet. See Figure A.
Note: The Pivot Hinges on the top of the Glass Door Panels have been preinstalled at the factory.
2 - Knobs
2 - Screws
4 - Rubber Washers
4 - Strike Plates
4 - Foam Pads (black)
2 - Pivot Hinges
4 - Set Screws
4 - Nylon Pads
2 - Nylon Washers (white)
4. With two people, attach the right Glass Door Panel to the cabinet.
• One person insert the preinstalled Pivot Hinge into the top Pivot Hinge Pin Hole and hold the Glass Door Panel in
position. Make certain the preinstalled Pivot Hinge has Set Screws facing the inside of the cabinet. See Figure B.
• With the first person holding the Glass Door Panel in position, the second person will hold the Nylon Pads against both
sides of the Glass Door Panel as they slide the bottom of the Glass Door Panel into the bottom Pivot Hinge. Install the
bottom of the Glass Door Panel into the bottom Pivot Hinge similar to the preinstalled top Pivot Hinge. See Figure B.
• Tighten the bottom Pivot Hinge Set Screws so they are snug – do not over tighten. Check the top Pivot Hinge Set
Screws to ensure they are also snug.
5. As necessary, adjust the Glass Door Panel so it can open and close
without interference.
6. Repeat steps 4 and 5 to install the left Glass Door Panel. Make certain the
left and right Glass Door Panels do not touch. Adjust the Glass Door Panels
as necessary.
7. Assemble a Knob (1) to both Glass Door Panels using Rubber Washers (2)
and Screw (1) as shown in Figure C.
8. Remove the protective paper from the adhesive side of the black Foam
Pad and attach a Foam Pad at the corners flush to the edge of the Glass
Door Panels. See Figure D.
9. Slide a Strike Plate over the four Foam Pads. Attach so the side with clear
protective cover is facing the inside of the cabinet.
• If the door does not catch firmly, remove the clear protective cover.
Top
Left
Top
Right
497270
12/2021
Figure B
CAUTION: Two people are required to
assemble the Glass Door Panels to the
cabinet. Use care when handling the
Glass Door Panels. To avoid bodily injury or
harm, assemble Glass Door Panels in an
area without children or other potential
hazards present.
1. Choose a location for the curio display cabinet. Refer to your cabinet
set-up instructions. Securely fasten the wall safety strap to the cabinet
and wall and install glass shelves prior to Glass Door Panel assembly.
2. Unpack the Glass Door Panels and set aside in a safe location.
3. Install a Nylon Washer (1) and Pivot Hinge (1) to the Pivot Hinge Pin Hole as shown at the bottom left and right of the
cabinet. Install the Pivot Hinges with the Set Screws facing the inside of the cabinet. See Figure A.
Note: The Pivot Hinges on the top of the Glass Door Panels have been preinstalled at the factory.
Nylon
Pads
Pivot
Hinge
Set Screw
Pivot Hinge
(Preinstalled)
Strike Plate
Screw
Knob
Rubber Washers
Foam Pad
Glass Door
Figure C
Figure D
Strike Plate
Glass
Door
4. With two people, attach the right Glass Door Panel to the cabinet.
• One person insert the preinstalled Pivot Hinge into the top Pivot Hinge Pin Hole and hold the Glass Door Panel in
position. Make certain the preinstalled Pivot Hinge has Set Screws facing the inside of the cabinet. See Figure B.
• With the first person holding the Glass Door Panel in position, the second person will hold the Nylon Pads against both
sides of the Glass Door Panel as they slide the bottom of the Glass Door Panel into the bottom Pivot Hinge. Install the
bottom of the Glass Door Panel into the bottom Pivot Hinge similar to the preinstalled top Pivot Hinge. See Figure B.
• Tighten the bottom Pivot Hinge Set Screws so they are snug – do not over tighten. Check the top Pivot Hinge Set
Screws to ensure they are also snug.
5. As necessary, adjust the Glass Door Panel so it can open and close
without interference.
6. Repeat steps 4 and 5 to install the left Glass Door Panel. Make certain the
left and right Glass Door Panels do not touch. Adjust the Glass Door Panels
as necessary.
7. Assemble a Knob (1) to both Glass Door Panels using Rubber Washers (2)
and Screw (1) as shown in Figure C.
8. Remove the protective paper from the adhesive side of the black Foam
Pad and attach a Foam Pad at the corners flush to the edge of the Glass
Door Panels. See Figure D.
9. Slide a Strike Plate over the four Foam Pads. Attach so the side with clear
protective cover is facing the inside of the cabinet.
• If the door does not catch firmly, remove the clear protective cover.
Top
Left
-
1
-
2
The Howard Miller 497270 is a curio display cabinet that allows you to showcase your收藏品and keepsakes behind glass doors. It features adjustable glass shelves, a wall safety strap for added security, and pre-installed pivot hinges for easy assembly. The cabinet also includes strike plates, nylon pads, and rubber washers for a secure fit.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Unbranded NAPVLY-236-12S-PRIMED Operating instructions
-
Kawasaki Mule 3000 Installation guide
-
U-Line Echelon CO2075FF User manual
-
-
Sterling Solitaire® Installation guide
-
-
Maytag PD User manual
-
-
-