LaCie 321 LCD Monitor with Blue Eye Pro Colorimeter User manual

Brand: LaCie

Model: 321 LCD Monitor with Blue Eye Pro Colorimeter

Category: TVs & monitors

Type: User manual

This manual is also suitable for

LaCie 300 Series LCD Monitor

User Manual

page 1

Table of Contents

Forward

Safety Precautions and Maintenance 3

Health and Ergonomic Precautions 4

Environmental Regulations 5

Manufacturer’s Recycling and Energy Information 6

Monitor Speciﬁcations 7

1. Introduction to Your LaCie 300 Series LCD Monitor

1.1. 300 Series Monitor Capabilities 8

1.2. Minimum System Requirements 9

1.3. Package Content 9

2. Installing Your LaCie 300 Series LCD Monitor 10

3. Using Your LaCie 300 Series LCD Monitor 13

3.1. Physical Adjustments 13

3.1.1. Raise and lower monitor screen 13

3.1.2. Screen tilt 13

3.1.3. Screen rotation 14

3.1.4. Swivel 14

3.1.5. Remove monitor stand for mounting 15

3.1.6. Flexible arm installation 16

4. OSD (On-Screen Display) Control Button Functions 1

4.1. Brightness/Contrast Controls 18

4.2. Auto Adjust (Analog input only) 18

4.3. Image Controls 18

4.4. Color Control Systems 20

4.5. Tools 1 20

4.6. Menu Tools 23

4.7. Information 24

4.8. OSD Warnings 25

4.9. Advanced Menu Functions 25

4.10. Using the Auto Brightness Function 34

5. Troubleshooting 36

6. Contacting Customer Support 3

6.1. LaCie Technical Support Contacts 39

7. Warranty Information 40

LaCie 300 Series LCD Monitor

User Manual

page 2

Copyrights

reserved. No part of this publication

may be reproduced, stored in a retrieval

system, or transmitted in any form or by

any means, electronic, mechanical, pho-

tocopying, recording or otherwise, with-

out the prior written consent of LaCie.

Changes

e material in this document is for

information only and subject to change

without notice. While reasonable ef-

forts have been made in the preparation

of this document to assure its accuracy,

LaCie assumes no liability resulting

from errors or omissions in this docu-

ment, or from the use of the informa-

tion contained herein. LaCie reserves

the right to make changes or revisions

in the product design or the product

manual without reservation and without

obligation to notify any person of such

revisions and changes.

FCC Declaration of Conformity:

Tested To Comply

With FCC standards

For Home of Oﬃce Use

LaCie 300 Series

LCD Monitor

NOTE: is equipment has been

tested and found to comply with the

limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules.

ese limits are designed to provide

reasonable protection against harm-

ful interference in a residential instal-

lation. is equipment generates, uses

and can radiate radio frequency energy

and, if not installed and used in accor-

dance with the instructions, may cause

harmful interference to radio commu-

nications. However, there is no guaran-

tee that interference will not occur in a

particular installation. If this equipment

does cause harmful interference to radio

or television reception, which can be de-

termined by turning the equipment oﬀ

and on, the user is encouraged to try and

correct the interference by one or more

of the following measures:

Reorient or relocate the receiving an-

tenna.

Increase the separation between the

equipment and receiver.

Connect the equipment into an out-

let on a circuit diﬀerent from that to

which the receiver is connected.

Consult the dealer or an experienced

radio/TV technician for help.

Use only shielded cables to connect

I/O devices to this equipment.

Use the attached speciﬁed cables

with the LaCie 300 Series color moni-

tor so as not to interfere with radio and

television reception.

1. e power supply cord you use must

have been approved by and comply

with the safety standards of U.S.A.

and meet the following condition.

Power supply

chord

Non shield type,

3-conductor

Length

2.0 m

Plug shape

(USA)

2. Please use the supplied shielded video

signal cable, 15-pin mini D-SUB to

•

DVI-A cable or DVI-D to DVI-D

cable. Use of other cables and adapt-

ers may cause interference with radio

and television reception.

U.S. Responsible Party: LaCie, LTD

Address: 22985 NW Evergreen Pkwy

Hillsboro, OR 97124

Tel. No.: (503) 844-4503

Manufacturer’s Declaration for

CE Certiﬁcation

We, LaCie, solemnly declare that this

product conforms to the following Eu-

ropean standards:

EN60950-1, EN61000-3-2

EN61000-3-3, EN55024

With reference to the following condi-

tions:

73/23/EEC Low Voltage Directive

89/336/EEC EMC Directive

LaCie, Inc.

17, Rue Ampère

91349 Massy Cedex, France

•

Forward

CAUTION: Modiﬁcations not

authorized by the manufacturer

may void the user’s authority to

operate this device. Modiﬁcations

not authorized by the manufactur-

er may void the user’s authority to

operate this device.

CAUTION: A shielded-type

power cord is required in order to

meet FCC emission limits and also

to prevent interference to the near-

by radio and television reception. It

is essential that only the supplied

power cord be used.

LaCie 300 Series LCD Monitor

User Manual

page 3

Safety Precautions and Maintenance

DO NOT OPEN THE MONI-

TOR. ere are no user serviceable

parts inside and opening or removing

covers may expose you to dangerous

shock hazards or other risks. Refer all

servicing to qualiﬁed service person-

nel.

Do not spill any liquids into the cabi-

net or use your monitor near water.

Do not insert objects of any kind into

the cabinet slots, as they may touch

dangerous voltage points, which can

be harmful or fatal or may cause elec-

tric shock, ﬁre or equipment failure.

Do not place any heavy objects on

the power cord. Damage to the cord

may cause shock or ﬁre.

Do not place this product on a slop-

ing or unstable surface, as the moni-

tor may fall, causing serious damage.

Do not place any objects onto the

monitor and do not use the monitor

outdoors.

e inside of the ﬂuorescent tube

located within the LCD monitor

contains mercury. Please follow the

bylaws or rules of

your municipality to dispose of the

tube properly.

Do not bend power cord.

Do not use monitor in high tempera-

tured, humid, dusty, or oily areas.

Do not cover vent on monitor.

Immediately unplug your monitor

from the outlet and refer servicing to

•

qualiﬁed personnel under the following

conditions:

When the power supply cord or plug

is damaged.

If liquid has been spilled, or objects

have fallen into the monitor.

If the monitor has been exposed to

rain or water.

If the monitor has been dropped or

the cabinet damaged.

If the monitor does not operate nor-

mally by following operating instruc-

tions.

If glass is broken, handle with care.

If monitor or glass is broken, do not

come in contact with the liquid crys-

tal and handle with care.

Allow adequate ventilation around

the monitor so that heat can properly

dissipate. Do not block ventilated

openings or place the monitor near

a radiator or other heat sources. Do

not put anything on top of monitor.

e power cable connector is the pri-

mary means of detaching the system

from the power supply. e monitor

should be installed close to a power

outlet which is easily accessible.

Handle with care when transporting.

Save packaging for transporting.

Image Persistence: Please be aware

that LCD Technology may experi-

ence a phenomenon known as Image

Persistence.

•

Image Persistence occurs when a re-

sidual or “ghost” image of a previous

image remains visible on the screen.

Unlike CRT monitors, LCD moni-

tors’ image persistence is not per-

manent, but constant images being

displayed for a long period of time

should be avoided. To alleviate im-

age persistence, turn oﬀ the monitor

for as long as the previous image was

displayed. For example, if an image

was on the monitor for one hour, the

monitor should be turned oﬀ for one

hour to erase the image.

When operating the LaCie 300 Se-

ries LCD Monitor with a 220-240V

AC power source in Europe, use the

power cord provided with the moni-

tor.

In the UK, a BS approved power cord

with a moulded plug has a Black (ﬁve

Amps) fuse installed for use with this

equipment.

If a power cord is not supplied with

this equipment please contact your

supplier.

When operating the LaCie 300 Se-

ries LCD Monitor with a 220-240V

AC power source in Australia, use the

power cord provided with the moni-

tor. If a power cord is not supplied

with this equipment please contact

your supplier.

For all other cases, use a power cord

that matches the AC voltage of the

power outlet and has been approved

by and complies with the safety stan-

dard of your particular country.

•

LaCie 300 Series LCD Monitor

User Manual

page 4

Health and Ergonomic Precautions

Correct placement and adjustment

of the monitor can reduce eye, shoulder

and neck fatigue. Check the following

when you position the monitor:

For optimum performance, allow 20

minutes for warm-up.

Adjust the monitor height so that the

top of the screen is at or slightly be-

low eye level. Your eyes should look

slightly downward when viewing the

middle of the screen.

Position your monitor no closer than

40 cm and no further away than 70

cm from your eyes. e optimal dis-

tance is 50 cm.

•

Rest your eyes periodically by focus-

ing on an object at least 20 feet away.

Blink often.

Position the monitor at a 90° angle

to windows and other light sources to

minimize glare and reﬂections. Ad-

just the monitor tilt so that ceiling

lights do not reﬂect on your screen.

If reﬂected light makes it hard for

you to see your screen, use an anti-

glare ﬁlter.

Clean the lcd monitor surface with a

lint-free, non-abrasive cloth. Avoid

using any cleaning solution or glass

cleaner!

•

Adjust the monitor’s brightness and

contrast controls to enhance read-

ability.

Use a document holder placed close

to the screen.

Position whatever you are looking at

most of the time (the screen or refer-

ence material) directly in front of you

to minimize turning your head while

you are typing.

Avoid displaying ﬁxed patterns on

the monitor for long periods of time

to avoid image persistence (after-im-

age eﬀects).

•

Health and Ergonomic Precautions

To maximize ergonomics beneﬁts,

we recommend the following:

Adjust the brightness until the back-

ground raster disappears.

Do not position the contrast control

to its maximum setting.

Use the preset size and position con-

trols with standard signals.

•

Use the preset color setting.

Use non-interlaced signals with a

vertical refresh rate between 60-75

hz.

Do not use primary color blue on a

dark background, as it is diﬃcult to

see and may produce eye fatigue to

insuﬃcient contrast.

•

LaCie 300 Series LCD Monitor

User Manual

page 5

Environmental Regulations

Congratulations! You

have just purchased a

TCO’03 approved and

labeled product! Your

choice has provided you with a prod-

uct developed for professional use. Your

purchase has also contributed to reduc-

ing the burden on the environment an

to the further development of environ-

mentally adapted electronics products.

Why do we have environmen-

tally labeled computers?

In many countries, environmen-

tal labeling has become an established

method for encouraging the adaptation

of goods to the environment. e main

problem, as far as computers and other

electronics equipment are concerned, is

that environmentally harmful substances

are used both in the products and during

the manufacturing. Since it has not been

possible for the majority of electronics

equipment to be recycled in a satisfacto-

ry way, most of these potentially damag-

ing substances sooner or later enter Na-

ture. ere are also other characteristics

of a computer, such as energy consump-

tion levels, that are important from the

viewpoints of both the work (internal)

and natural (external) environments.

Since all methods of conventional elec-

tricity generation have a negative eﬀect

on the environment (acidic and climate-

inﬂuencing emissions, radioactive waste,

etc.), it is vital to conserve energy. Elec-

tronics equipment in oﬃces consume an

enormous amount of energy since they

are often left running continuously.

■

What does labeling involve?

is product meets the requirements

for international and environmental

labeling of personal computers. e

requirements cover a wide range of is-

sues, including: environment, ergonom-

ics, usability, emission of electrical and

magnetic ﬁelds, energy consumption

and electrical and ﬁre safety. e envi-

ronmental demands concern restrictions

on the presence and use of heavy met-

als, brominated and chlorinated ﬂame

retardants, CFCs (freons) and chlori-

nated solvents, among other things. e

product must be prepared for recycling

and the manufacturer is obliged to have

an environmental plan which must be

adhered to in each country where the

company implements its operational

policy. e energy requirements include

a demand that the computer and/or dis-

play, after a certain period of inactivity,

shall reduce its power consumption to a

lower level in one or more stages. e

length of time to reactivate the com-

puter shall be reasonable for the user.

Labeled products must meet strict en-

vironmental demands, for example, in

respect of the reduction of electric and

magnetic ﬁelds, physical and visual er-

gonomics and good usability.

Environmental Requirements

Flame retardants

Flame retardants are present in

printed circuit boards, cables, wires, cas-

ings and housings. In turn, they delay

the spread of ﬁre. Up to thirty percent

of the plastic in a computer casing can

■

consist of ﬂame retardant substances.

Most ﬂame retardants contain bromine

or chloride and these are related to an-

other group of environmental toxins,

PCBs, which are suspected to give rise

to severe health eﬀects, including repro-

ductive damage in ﬁsh-eating birds and

mammals, due to the bio-accumulative*

processes. Flame retardants have been

found in human blood and researchers

fear that disturbances in fetus develop-

ment may occur. Plastic components

weighing more than 25 grams must not

contain ﬂame retardants with organical-

ly bound chlorine and bromine. Flame

retardants are allowed in the printed

circuit boards since no substitutes are

available.

Lead**

Lead can be found in picture tubes,

display screens, solders and capacitors.

Lead damages the nervous system and

in higher doses, causes lead poisoning.

Requirements permit the inclusion of

lead since no replacement has yet been

developed.

Cadmium**

Cadmium is present in recharge-

able batteries and in the color-generat-

ing layers of certain computer displays.

Cadmium damages the nervous system

and is toxic in high doses. Requirements

state that batteries, the color-generating

layers of display screens and the electri-

cal or electronics components must not

contain any cadmium.

Environmental Regulations

LaCie 300 Series LCD Monitor

User Manual

page 6

Environmental Regulations

Mercury**

Mercury is sometimes found in

batteries, relays and switches, Mercury

damages the nervous system and is toxic

in high doses. Requirements state that

batteries may not contain any Mercury.

It also demands that no mercury is pres-

ent in any of the electrical or electronics

components associated with the display

unit.

CFCs (freons)

CFCs (freons) are sometimes used

for washing printed circuit boards. CFCs

break down ozone and thereby dam-

age the ozone layer in the stratosphere,

causing increased reception on Earth

of ultraviolet light with consequent in-

creased risks of skin cancer (malignant

melanoma). e relevant requirement;

Neither CFCs nor HCFCs may be used

during the manufacturing and assembly

of the product or its packaging.

*Bio-accumulative is deﬁned as substances

which accumulate within living organisms.

**Lead, Cadmium and Mercury are heavy

metals which are bio-accumulative.

is symbol on the product

or on its packaging indicates

that this product must not

be disposed of with your

other household waste. Instead, it is

your responsibility to dispose of your

waste equipment by handing it over to

a designed collection point for the re-

cycling of waste electrical and electronic

equipment. e separate collection and

recycling of your waste equipment at the

time of disposal will help to conserve

natural resources and ensure that it is re-

cycled in a manner that protects human

health and the environment. For more

information about where you can drop

oﬀ your waste equipment for recycling,

please contact your local city oﬃce, your

household waste disposal service, or the

shop where you purchased the product.

LaCie is strongly committed to envi-

ronmental protection and sees recycling

as one of the company’s top priorities in

trying to minimize the burden placed

on the environment. We are engaged

in developing environmentally friendly

products, and always strive to help de-

ﬁne and comply with the latest indepen-

dent standards from agencies.

Recycling programs information:

Sweden - http://www.el-retur.se

Germany - http://www.recyclingpartner.de/

Holland - http://www.mirec.nl/

Japan - http://www.diarcs.com/

Energy saving:

is monitor features an advanced

energy saving capability. When a VESA

Display Power Management Signaling

(DPMS) Standard signal is sent to the

monitor, the Energy Saving mode is ac-

tivated. e monitor enters a single En-

ergy Saving mode.

Manufacturer’s Recycling and Energy Information

Mode Power consumption LED color

Normal operation 46W (319), 50W (320/321) Blue

Energy saving mode Less than 1W Amber

Oﬀ mode Less than 1W N/A

LaCie 300 Series LCD Monitor

User Manual

page 7

Monitor Speciﬁcations

319 LCD Monitor 320 LCD Monitor 321 LCD Monitor

Technology:

S-IPS A-TW-IPS SA-SFT

Diagonal display:

19.0” (48 cm) 20.1” (51 cm) 21.0” (53.3 cm)

Active Display:

376.3 (H) x 301.1 (V) mm 408 (H) x 306 (V) mm 432 (H) x 324 (V) mm

Resolution:

720 x 400 at 70 Hz to 85 Hz; 640 x 480 at 60 Hz to 85 Hz; 800 x 600 at 56 Hz to 85 Hz;

832 x 624 at 75 Hz; 1024 x 768 at 60 Hz to 85 Hz; 1152 x 864 at 70 Hz to 85 Hz;

1152 x 870 at 75 Hz; 1280 x 960 at 60 Hz; 1280 x 1024 at 60 Hz to 85 Hz (Optimal resolu-

tion for LaCie 319); 1200 x 1600 at 60 Hz; 1600 x 1200 at 60 Hz (Optimal resolution for

LaCie 320 and 321, not supported for 319); some systems may not support all modes listed.

Pixel pitch:

0.294 mm 0.255 mm 0.270 mm

Color depth:

16,777,216

Gamma correction:

12 bit

Luminance:

270 cd/m

(typical)

280 cd/m

(typical)

250 cd/m

(typical)

Contrast ratio:

600:1 (typical) 700:1 (typical) 500:1 (typical)

Response time:

Rise time + Fall time :

18ms (typical)

Rise time + Fall time :

16ms (typical)

Rise time + Fall time : 20ms

(typical)

Viewing angles:

178°

Connections:

Mini D-sub 15 pin, DVI-I (analog or digital), DVI-D (digital)

Power consumption:

46 W (typical) 50 W (typical) 50 W (typical)

In power save mode

< 1 W

Weight:

6.3 kg 7.0 kg 8.2 kg

Weight with stand:

9.0 kg 9.7 kg 10.9 kg

Box weight:

13.4 kg 14.2 kg 16.3 kg

Box dimensions:

(WxHxD) 508 x 600 x 321 mm (WxHxD) 558 x 641 x 325 mm (WxHxD) 620 x 685 x 370 mm

Ergonomy:

Up/down: 30° to -5°; left/right: 170° to 170°; clockwise: 90°; height adjustment: 150 mm

Operating Temp.:

5°C to 35°C/41°F to 95°F

Humidity:

30% to 80%

Altitude:

0 to 10,000 feet / 0 to 3,048 m

Storing Temp.:

-10°C to 60°C / 14°F to 140°F

Storing Humidity:

10% to 85%

Storing Altitude:

0 to 40,000 feet / 0 to 12,192 m

Certiﬁcations:

CE, FCC-B, TÜV-Ergonomie, TÜV-GS, TCO’03, EnergyStar, C-Tick, GOST-R, c-UL,

UL, VCCI-B, VESA DDC 2B, DDC-CI

Warranty:

US: 3-year limited; Europe: 3-year advance swap

Values for when the UNIFORMITY function is OFF.

LaCie 300 Series LCD Monitor

User Manual

page 8

Introduction

1. Introduction to Your LaCie 300 Series LCD Monitor

ank you for purchasing the LaCie 300 Series

LCD Monitor. Designed for serious graphics profes-

sionals, these LCD monitors feature 12-bit gamma cor-

rection to meet the challenge of today’s color needs.

1.1. 300 Series Monitor Capabilities

IPS (LaCie 319), A-TW-IPS (LaCie 320) and SA-

SFT-IPS (LaCie 321) panel technologies oﬀer the

best available LCD color accuracy, with a good balance

between Contrast, Brightness and Expansive Viewing

Angles of 178°.

Improved uniformity: Each panel is individually test-

ed at the factory and corrected to ensure that bright-

ness and chromaticity are uniform across the screen.

12-bit gamma correction: An embedded Integrated

Circuit containing 12-bit color correction tables en-

ables true hardware calibration of the display.

LaCie blue eye pro software included: is complete

yet easy-to-use calibration software oﬀers professional

grade calibration and ICC proﬁling of the monitors

on Mac OSX, Windows XP, 2000, and XP64.

Monitor easyHood included: e black, anti-reﬂec-

tive velvet material that lines the easyHood reduces

ambient light glare and ensures document colors are

accurately seen by the user.

Ergonomic stand enabling Height- Swivel- Tilt- and

Pivot- adjustments

Pivot Pro software for Windows included: In con-

junction with the monitor stand’s mechanical Pivot

adjustment, this software allows the user to eﬀectively

rotate the desktop and work in Landscape mode.

Portability handle and quick-release stand make

your LaCie 300 Series Monitor easy to carry.

•

LaCie 300 Series LCD Monitor

User Manual

page 9

Introduction

1.2. Minimum System Requirements

Hardware Requirements■

DVI graphics board required for automatic hardware calibration•

1.3. Package Content

LaCie 300 Series LCD Monitor with tilt/

swivel/pivot/height adjustable stand

Power cord

Screws (to mount the monitor to a ﬂexible arm)

Cable cover

Video signal cable (15-pin mini D-SUB male

to DVI-A)

Video signal cable (DVI-D to DVI-D cable)

easyHood

LaCie Utilities CD-ROM (includes User

Manual and blue eye pro calibration software)

Quick Install Guide

Pivot Pro Software

Your LaCie 300 Series LCD monitor should contain the following:

1 3

LaCie User Manual

ICC Profiles Included

LaCie 300 Series LCD Monitor

Version 2.0

Manuel Utilisateur • Guída Utente • Handbuch •

Manual De Instrucciones • Gebruikershandleiding

Profiles ICC inclus • Profili ICC inclusi

ICC Profile inbegriffen • Perfiles ICC incluidos

Quick Install Guide

LaCie 300 Series LCD Monito

ImpOrTANT INfO: Please save your packaging. In the event that the monitor should need to be repaired or

serviced, it must be returned in its original packaging.

LaCie 300 Series LCD Monitor

User Manual

page 10

Installing Your LaCie Monitor

2. Installing Your LaCie 300 Series LCD Monitor

To attach the LCD monitor to your system, follow

these instructions:

1. Turn oﬀ the power to your computer.

2. For the PC or MAC with DVI digital output:

Connect the DVI signal cable to the connector of the

display card in your system (Figure A). Tighten all

screws.

For the PC with Analog output:

Connect the 15-pin mini D-SUB to DVI-A signal

cable to the connector of the display card in your sys-

tem (Figure B).

For the MAC:

Connect the Macintosh cable adapter to the comput-

er, then attach the 15-pin mini D-SUB signal cable to

the Macintosh cable adapter (Figure C).

Figure A Figure B Figure C

Mac Cable Adaptor

(not included)

TeChNICAl NOTe: Some Macintosh systems

do not require a Macintosh cable adapter.

LaCie 300 Series LCD Monitor

User Manual

page 11

Installing Your LaCie Monitor

3. Place hands on each side of the monitor to tilt the

LCD panel to a 30-degree angle and lift up to the

highest position (Figure D).

4. Connect all cables to the appropriate connectors (Fig-

ure D).

5. To keep the cables neatly organized, place them into

the cable management system that is built into the

stand.

Place the D-Sub cable (not included) and the

power cable into the speciﬁc hooks as indicated

(Figure E).

Place the DVI cable and the 15-pin mini D-Sub

to DVI-A cable into the hooks as indicated (Fig-

ure F).

When using the monitor in Portrait mode, place

the DVI cable and the 15-pin mini D-Sub to

DVI-A cable into the hooks as indicated (Figure

G).

6. Make sure all cables are resting ﬂat against the stand

(Figure F). Please check Tilt, Rise and Lower moni-

tor screen and screen rotation when you manage

cables.

•

Figure D

CAUTION: Incorrect cable connections may

result in irregular operation, damage display qual-

ity/components of LCD module and/or shorten

the module’s life.

Figure E Figure F

Highest

Stand

Position

30° Tilt

DVI-I

DVI-D

D-SUB

Figure G

LaCie 300 Series LCD Monitor

User Manual

page 12

Installing Your LaCie Monitor

TeChNICAl NOTe: Please refer to Caution

section of this manual for proper selection of AC

power cord.

7. Hold all cables ﬁrmly and place the cable cover onto

the stand (Figure H). To remove the cable cover, lift

the cover oﬀ as shown in Figure H.

8. Connect one end of the power cord to the AC inlet

on the back of the monitor and the other end to the

power outlet.

9. e Vacation Switch on the left side of the moni-

tor must be turned on. Turn on the monitor with the

front power button (Figure J) and the computer.

TeChNICAl NOTe: e Vacation Switch is a

true on/oﬀ switch. If this switch is on the OFF po-

sition, the monitor cannot be turned on using the

front button. DO NOT switch on/oﬀ repeatedly.

10. No-touch auto adjust automatically adjusts the

monitor to optimal settings upon initial setup for

most timings. For further adjustments, use the fol-

lowing OSD (on-screen display) controls:

Auto Contrast (Analog input only)

Auto Adjust (Analog input only)

Refer to the page 17, OSD Control Button Functions,

for a full description of these OSD controls.

•

Figure H Figure I

Figure J

Vacation

Switch

Power

Button

LaCie 300 Series LCD Monitor

User Manual

page 13

Using Your LaCie Monitor

3. Using Your LaCie 300 Series LCD Monitor

3.1. Physical Adjustments

e monitor may be raised or lowered in either Por-

trait or Landscape mode.

To raise or lower screen, place hands on each side

of the monitor and lift or lower to the desired height

(Figure A and B).

TeChNICAl NOTe: Handle with care when

raising or lowering the monitor screen.

Figure BFigure A

3.1.1. Raise and lower monitor screen■

3.1.2. Screen tilt■

Grasp top and bottom sides of the monitor screen with

your hands and adjust the tilt as desired (Figure C).

Figure C

TeChNICAl NOTe: Handle with care when

tilting the monitor screen.

LaCie 300 Series LCD Monitor

User Manual

page 14

Using Your LaCie Monitor

Before rotating, the screen must be raised to the

highest level to avoid knocking the screen on the desk

or pinching with your ﬁngers.

To raise the screen, place your hands on each side

of the monitor and lift up to the highest position (page

13, ﬁgure B).

To rotate the screen, place hands on each side of the

monitor screen and turn clockwise from Landscape to

Portrait or counterclockwise from Portrait to Landscape

(Figures D and E).

To rotate the OSD menu between landscape and

portrait, refer to “Controls” section.

Mac Users

Portrait mode requires a high end graphic board

such as the ATI Radeon x800 or internal ATI graphic

chip.

PC Users

Use the Pivot Pro software that ships with your

LaCie 300 series monitor.

Figure E

Figure D

3.1.3. Screen rotation■

3.1.4. Swivel■

Grasp both sides of the monitor screen with your hands

and adjust the swivel as desired (Figure F).

Figure F

LaCie 300 Series LCD Monitor

User Manual

page 15

Using Your LaCie Monitor

3.1.5. Remove monitor stand for mounting■

To prepare the monitor for alternate mounting pur-

poses:

1. Disconnect all cables.

2. Place hands on each side of the monitor and lift up to

the highest position.

3. Place monitor face down on a non-abrasive surface

(Figure G).

Figure G

TeChNICAl NOTe: Use only VESA-compat-

ible alternative mounting method (100 mm pitch).

ImpOrTANT INfO: Handle with care when

removing monitor stand.

4. Place one hand around the base and one hand on the

Quick Release Lever. Move the Quick Release Lever

in the direction indicated by the arrows (Figure H).

5. Lift up the bottom of the stand to unhook it from the

monitor (Figure I). e monitor can now be mounted

using and alternating method. Reverse process to re-

attach stand.

Figure IFigure H

Slide

LaCie 300 Series LCD Monitor

User Manual

page 16

Using Your LaCie Monitor

3.1.6. Flexible arm installation■

is LCD monitor is designed for use with a ﬂex-

ible arm.

1. Follow the instructions on how Remove Monitor

Stand for Mounting to remove the stand.

2. Using the 4 screws from the stand removal and attach

the arm to the monitor (Figure J).

Figure J

ImpOrTANT INfO: Use ONLY the screws

that are included when mounting to avoid damage

to the monitor and stand.

To fulﬁl the safety requirements the monitor must

be mounted to an arm which guaranties the nec-

essary stability under consideration of the weight

of the monitor.

e LCD monitor can be used with an arm (e.g.

the LaCie Twin Arm or the LaCie Articulated

Arm).

LaCie 300 Series LCD Monitor

User Manual

page 17

OSD Control Button Functions

4. OSD (On-Screen Display) Control Button Functions

To access OSD menu, press any of the control but-

tons (EXIT, LEFT, RIGHT, UP, DOWN).

To change signal input, press the SELECT button.

TeChNICAl NOTe: e OSD must be closed

in order to change signal input.

1 POWER Turns the monitor on and oﬀ.

2 LED Indicates that the power is on.

3 INPUT/SELECT Enters OSD sub menus. Changes the input source when not in the OSD Control menu.

4 MENU/EXIT Opens/Exits the OSD sub menu. Opens/Exits OSD Control menu.

5 LEFT/RIGHT Navigates to the left or right through the OSD Control menu.

6 UP/DOWN Navigates up or down through the OSD Control menu.

7 RESET/ROTATE

OSD

Resets the OSD back to factory settings. When pressed when the OSD is not showing, rotates

the OSD Control menu between portrait and landscape mode.*

8 KEY GUIDE e Key Guide appears on screen when the OSD control menu is accessed. e Key Guide will

rotate when the OSD control menu is rotated.

* e “LEFT/RIGHT” and “UP/DOWN” buttons function-

ality is interchangeable depending on the orientation (land-

scape/portrait) of the OSD.

4 5 6 7

LaCie 300 Series LCD Monitor

User Manual

page 18

OSD Control Button Functions

Symbol Menu title Explanation

BRIGHTNESS Adjusts the overall image and background screen brightness.

CONTRAST Adjusts the image brightness in relation to the background.

BLACK LEVEL

Adjust the black level.

4.1. Brightness/Contrast Controls

Symbol Menu title Explanation

Automatically adjusts the Image Position and H. Size settings and Fine settings.

4.2. Auto Adjust (Analog input only)

4.3. Image Controls

Symbol Menu title Explanation

LEFT / RIGHT Controls Horizontal Image Position within the display area of the LCD.

DOWN / UP Controls Vertical Image Position within the display area of the LCD.

AUTO FINE

(Analog input only)

is function automatically and periodically adjusts the FINE setting for

change in signal condition. is function adjusts approximately every 33 min-

utes or when a change in signal timing is detected.

EXPANSION Sets the zoom method.

FULL: e image is expanded to 1280 x 1024 (319 model), 1600 x 1200 (320

model), and 1600 x 1200 (321 model), regardless of the resolution.

ASPECT: e image is expanded without changing the aspect ratio.

OFF: e image is not expanded.

CUSTOM: Refer to the ADVANCED OSD Controls menu section of the

user manual for detailed instructions.

(Continued on next page)

LaCie 300 Series LCD Monitor

User Manual

page 19

OSD Control Button Functions

Symbol Menu title Explanation

H.SIZE (V.SIZE)

(Analog input only)

Adjusts the horizontal size by increasing or decreasing this setting. If the

“AUTO Adjust function” do not give you a satisfactory picture setting, a further

tuning can be performed using the “H.Size (or V.Size)” function (dot clock).

For this a Moiré test pattern could be used. is function may alter the width of

the picture. Use LEFT/RIGHT Menu to center the image on the screen. If the

H.Size (or V.Size) is wrongly calibrated, the result would look like on the left

drawing. e image should be homogeneous.

FINE

(Analog input only)

Improves focus, clarity and image stability by increasing or decreasing this

setting. If the “Auto Adjust function” and the “H.Size” function do not give

you a satisfactory picture setting, a ﬁne tuning can be performed using the

FINE function. For this a Moiré test pattern could be used. If the Fine value

is wrongly calibrated, the result would look like on the left drawing. e image

should be homogeneous.

When FINE

value is incorrect

When FINE

value is correct

When H.SIZE

value is incorrect

When H.SIZE

value is improved

When H.SIZE

value is correct

(Continued from previous page)

LaCie 300 Series LCD Monitor

User Manual

page 20

OSD Control Button Functions

Symbol Menu title Explanation

Seven color presets select the desired color setting (sRGB, NATIVE and PROGRAMMABLE color

presets are standard and cannot be changed).

1, 2, 3 and 5: Increases or decreases Color temperature, Red, Yellow, Green, Cyan, Blue, Magenta de-

pending upon which is selected. e change in color will appear on screen and the direction (increase or

decrease) will be shown by the color bars.

NATIVE, sRGB Original color presented by the LCD panel that is not adjustable.

PROGRAMMABLE e color tone that was set up with the downloaded application software is

reﬂected.

4.4. Color Control Systems

TeChNICAl NOTe: To reset a poor image set-

ting, turn on the monitor by using front power but-

ton while holding RESET and SELECT buttons

at the same time.

Symbol Menu title Explanation

SHARPNESS is function is digitally capable to keep crisp image at any timings. It is

continuously adjustable to get distinct image or soft one as you prefer, and set

independently by diﬀerent timings.

DVI SELECTION is function selects the DVI input mode (DVI-I). When the DVI selection

has been changed, the computer has to be restarted.

AUTO

By using the D-SUB to DVI-A cable, the DVI SELECTION is DIGITAL.

By using the DVI-D to DVI-D cable, the DVI SELECTION is ANALOG.

DIGITAL

DVI digital input is available.

ANALOG

DVI analog input is available.

4.5. Tools 1

(Continued on next page)

Page is loading ...

LaCie 321 LCD Monitor with Blue Eye Pro Colorimeter User manual

Brand: LaCie

Model: 321 LCD Monitor with Blue Eye Pro Colorimeter

Category: TVs & monitors

Type: User manual

This manual is also suitable for

Download PDF

report

LaCie 321 LCD Monitor with Blue Eye Pro Colorimeter User manual

This manual is also suitable for

LaCie 321 LCD Monitor with Blue Eye Pro Colorimeter User manual

Related papers

Other documents