Progress Lighting 93109040 E Installation guide

Brand: Progress Lighting

Model: 93109040 E

Type: Installation guide

Progress Lighting 93109040 E is a highly efficient LED Wallpack luminaire designed for both indoor and outdoor use. With its rugged construction and IP65 rating, it can withstand harsh weather conditions, making it ideal for illuminating building exteriors, parking lots, and other outdoor areas. The luminaire's long-lasting LED technology provides up to 50,000 hours of maintenance-free operation, significantly reducing the need for frequent bulb replacements. Additionally, the luminaire's adjustable mounting arm allows for precise positioning, ensuring optimal light distribution.

INSTALLATION INSTRUCTION MANUAL

LED WALLPACKS LUMINAIRE, 120-277VAC

MODELS:

ϱϬt >&ƵůůƵƚͲŽĨĨtĂůůƉĂĐŬ

Model number parameter list:

CAUTION: If a photocell is installed with this luminaire, make sure the rated voltage of the photocell meets or

exceeds the actual supply voltage.

1. Introduction

This LED Wall-Pack luminaire uses the latest in solid state lighting technology for long life, low

maintenance, and high efficiency.

Button-type photocells can be installed in the threaded (1/2” NPS) receptacles in the housing.

An internal power-factor-corrected switch-mode supply allows the luminaire to be used with a nominal

120V-277V, 50/60Hz AC supply without any variation in light output.

Suitable for use in the wet locations in ambient temperatures ranging from -20°C~+40°C / -4°F to 104°F.

Note: Save these instructions for future reference.

2. Install Guidelines

Item

Model

Input Voltage

Power Factor

Watts

Input Current

50W Wallpack

120-277VAC

≥0.9

50W

0.52A MAX

Warning:

To avoid the risk of fire, explosion, or electric shock, this product should be installed,

inspected, and maintained by a qualified electrician only, in accordance with all applicable

electrical codes.

Warning:

To avoid electric shock:

•Be certain electrical power is OFF before and during installation and maintenance.

•Luminaire must be connected to a wiring system with an equipment-grounding conductor.

Customer Service: 1-800-447-1723 PAGE 1 of 4 93109040 08/15/19

For supply connections use wire rated for at least 80°.

Installation:

Warning:

To avoid explosion:

•Make sure the supply voltage is the same as the rated luminaire voltage.

•Do not install where marked operating temperatures exceed the ignition temperature of

the hazardous atmosphere.

•Do not operate in ambient temperatures above those indicated on the luminaire

nameplate.

•Keep lens tightly closed when in operation.

FIG.2

FIGURE 2

FIGURE 1

145.5mm

167.5mm

Customer Service: 1-800-447-1723 PAGE 2 of 4 93109040 08/15/19

FIGURE 3

FIGURE 4

Luminaire Door

Luminaire Back Box

Customer Service: 1-800-447-1723 PAGE 3 of 4 93109040 08/15/19

Step 1

Separate the back box from the luminaire door by using a philips screw driver (FIGURE 2). Refer

to the dimensions shown in FIGURE 1 to drill the holes in the wall (FIGURE 1).

Step 2

Use wire nuts to connect incoming power wires to the luminaire power wires (black to line,

white to neutral, and green/yellow to ground (see FIGURE 5).

Step 3

Install the luminaire back box on the wall.

Step 4

Reattach the luminaire door and tighten the screws to seal the luminaire (see FIGURE 4).

After installation,

Make sure the lighting fixture is firmly attached to the mounting surface.

Make sure all wires are connected correctly.

At last, turn on the power, and check if the lighting fixture works well. If not, please turn off the power

and contact with local dealer.

Warning: the luminaire shall be installed by qualified electrician.

Customer Service: 1-800-447-1723 PAGE 4 of 4 93109040 08/15/19

Progress Lighting 93109040 E Installation guide

Progress Lighting 93109040 E Installation guide

Progress Lighting 93109040 E Installation guide

Related papers

Other documents