Talent LP12LED User manual

Brand
Talent
Model
LP12LED
Category
Stroboscopes & disco lights
Type
User manual
User Manual
www.talentaudio.comwww.talentaudio.com
Model: LP12LED
WARRANTY
We at Talent are dedicated to providing our customers with professional, high
quality stage and studio accessories. As such, all Talent products are warranted
free from defects in material and workmanship for a period of One Year from
the date of purchase.
Warranty registration is not required, but purchasers are asked to retain their
receipt as proof of purchase. Warranty does not apply to misuse, abuse,
neglect, accident, improper use, etc.
For complete customer satisfaction, Talent resellers are asked to act as
agents for the purpose of handling warranty claims. Please return your Talent
product to your place of purchase prepaid. Many Talent resellers require a
return authorization (also known as an RA or RMA). Please contact your Talent
reseller for more details.
2 3
1. Safety Instructions
WARNING
• PleasekeepthisUserManualforfutureconsultation.Ifyousellthexturetoanother
user, be sure that they also receive this instruction booklet.
• Whenunpackingforrstuse,checkcarefullythereisnotransportationdamage.
• Before operating, ensure that the voltage and frequency of power supply match the
 powerrequirementsofthexture.
• Disconnect main power before servicing and maintenance.
• Useasafetycablewhenmountingthisxture.
• Maximumambienttemperatureis40°C.
• Intheeventofaseriousoperatingproblem,stopusingthextureimmediately.Never
 trytorepairthextureyourself.Repairscarriedoutbyunskilledpersonscanleadto
damage or malfunction. Please contact the nearest authorized technical assistance
center. Always use the same type spare parts.
• Do not connect the device to any dimmer pack.
• Do not touch any wire during operation, as there might be a hazard of electric shock.
• Topreventorreducetheriskofelectricalshockorre,donotexposethextureto
rain or moisture.
• The housing must be replaced if it is visibly damaged.
• DonotlookdirectlyattheLEDlightbeamwhilethextureison.
• Do not connect in series more than 30 units. Use another circuit to supply
 additionalxtures.
CAUTION
Therearenouserserviceablepartsinsidethexture.Donotopenthehousingorattempt
any repairs yourself. In the unlikely situation your unit may require service, please contact
your nearest dealer.
Please read the instructions carefully, which include important
information about installation, operation, and maintenance.
1. Safety Instructions
2. Technical Specications
3. Installation
4. How to Set the Unit
5. DMX512 Conguration
6. DMX512 Connections
7. Troubleshooting
8. Fixture Cleaning
TABLE OF CONTENTS
2. Technical Specications
5 channel DMX LED PAR light
Four modes: Automatic, Sound Activated, DMX512, Master/Slave
Power input: 90-250VAC50-60Hz
Power consumption: 12 watts
Light source: 12x1wattRGBUltraBrightLEDs
Bulb life: 3 to 5 million hours
Bulb angle: 45°
Dimensions: 150mmdiameter×210mmlong
Weight: 0.9kg
6 7
6. DMX512 Connections
The DMX512 protocol is used widely in intelligent lighting control, with a
maximumof512channels.
1. Ifyourcontrollerhasa5-pinDMXoutput,youneedtousea5-pinto3-pin
adapter cable.
2. Linkthexturestogetherina“daisychain”byconnectingXLRcablesfrom
 theoutputofthexturetotheinputofthenextxture.Thecablecannotbe
 branchedorsplittoa“Y”cable.Inadequateordamagedcables,soldered
joints, or corroded connectors can easily distort the signal and shut down
the system
3. TheDMXoutputandinputconnectorsarepass-throughtomaintaintheDMX
circuit when one of the units’ power is disconnected.
4. Atthelastxture,theDMXcableshouldbeterminatedtoreducesignal
 errors.Soldera120ohm1/4WresistorbetweenPin2(DMX-)andPin3
 (DMX+)intoa3-pinXLRplugandconnectittothelastxture’sDMXoutput.
5. Each lighting xture must have its address set to receive data sent by
the controller. The address number is between 0-511 (usually 0 & 1 are
equal to 1). Please refer to “4.2 Main Function” above.
6. 3-pinXLR:Pin1: GND,Pin2:Negativesignal(-),Pin3:Positivesignal(+)
5-pinXLR:Pin1: GND,Pin2:Negativesignal(-),Pin3:Positivesignal(+)
  Pin4/5:Notused.
7. Troubleshooting
Followingareafewcommonproblemsthatmayoccurduringoperation.Here
aresomesuggestionsforeasytroubleshooting:
A. The xture does not work, no light
1. Checktheconnectionofpowerandmainsfuse.
2. Measure the mains voltage on the main connector.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors and cables to
verify they are linked properly.
2. If the DMX LED is on and the channel does not respond, check the
address settings and DMX polarity.
3. IfyouhaveintermittentDMXsignalproblems,checkthecableandxture
connectors for proper function.
4. TrytouseanotherDMXcontrollerforcomparison.
5. CheckiftheDMXcablesarerunnearoralongsidehighvoltagecables
that may cause interference to the DMX interface circuit.
C. Some xtures don’t respond to the controller
1. YoumayhaveabreakintheDMXcabling.ChecktheLEDforthe
response of the master/ slave mode signal.
2. WrongDMXaddressinthexture.Settheproperaddress.
D. No response to sound
1. MakesurethexturedoesnotreceiveDMXsignal.
2. Checkmicrophonetoseeifitisgoodbytappingthemicrophone.
8. Fixture Cleaning
Cleanwithsoftclothusingaverymildhouseholddetergent.Alwaysdrythe
parts carefully.
4 5
4.2 Main Function
3. Installation
Theunitshouldbemountedviatheholesonitsbracket,andmustbexed
rmlytoavoidvibrationandslippageduringoperation.Alwaysensurethatthe
structuretowhichyouareattachingthelightingxtureissecureandableto
support10timestheunit’sweight.Wheninstallingthexture,useasafetycable
that can hold 12 times the weight of the unit.
4. How To Set The Unit
4.1 Control Panel
5. DMX512 Conguration
NOTE: When used in multiples, the LP12LED’s strobe and fade speed functions
willsynchronizewithadditionalLP12LEDxtures.Duetoslightvariationsthat
existbetween other manufacturers’controlprotocols,an LP12LEDmay not
be100%compatiblewithallmodelsorbrandsof5-channellightingdevices.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Talent LP12LED User manual

Brand
Talent
Model
LP12LED
Category
Stroboscopes & disco lights
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents