2. Omron
  3. V450

Omron V450 Configuration Guide

  • Hello! I've reviewed the Configuration Guide for the OMRON V450 Barcode Reader. This document provides detailed instructions on setting up the device using wired and wireless configurations, including USB, RS232, EtherNet/IP, PROFINET, and Bluetooth options. It also covers battery charging for wireless models. I'm ready to assist with any questions you might have about configuring the V450.
  • Do I need to order a battery with the wireless handheld unit?
    Can I connect the wireless cradle through USB? If so, will the cradle recharge the handheld’s battery?
    When connecting the V450 using RS232, does the unit need the external power supply?
    Is the wireless V450 Bluetooth?
Omron Automation Americas
2895 Greenspoint Parkway, Suite 200, Hoffman Estates, IL 60169
2801 Rochelle Rd., Suite 100, DFW Airport, TX 75261
100 Consilium Place, Suite 802, Toronto, Ontario, M1H 3E3
Configuration Guide for V450
Version 2.1, August-2023
Table of Contents ........................................................................................................................ 1
Introduction
Wired Configurations ............................................................................................................................ 2
USB
RS232
EtherNet/IP
PROFINET
Wireless Configurations ........................................................................................................................ 3
USB (Bus Powered)
USB (Separate Power)
RS232
Bluetooth
EtherNet/IP
PROFINET
Introduction
This guide was created to assist in selecting the correct part numbers for each possible configuration and
have been divided into two sections, wired and wireless. For each configuration you will find the corresponding
list of part numbers required. Please select the configuration that best suits your individual application.
Omron Automation Americas
2
Wired Configurations
USB
RS232
EtherNet/IP
PROFINET
Omron Automation Americas
3
Wireless Configurations
USB (Bus Powered)
RS232
USB (Separate Powered)
Bluetooth
Omron Automation Americas
4
EtherNet/IP
PROFINET
Omron Automation Americas
5
V450
Handheld Barcode Reader
Frequently Asked Questions
Q. Do I need to order a battery with the wireless handheld unit?
A. No, each wireless handheld unit (V450HDS36780001), includes a battery. Additional batteries (98-
9000224-01) can be ordered separately if you wish to have more than one.
Q. Can I connect the wireless cradle through USB? If so, will the cradle recharge the handheld’s
battery?
A. Yes, the USB is available for both the wired and wireless units. The USB bus cable (12900094601)
will provide power to the cradle and to recharge the battery. However the battery will recharge much
faster if the cradle is connected by the USB cable with separate power (12900094201) and power
supply (98900018101).
Q. When connecting the V450 using RS232, does the unit need the external power supply?
A. Yes, the RS232 connection requires the RS232C cable (12900095301) with power to be supplied
by the separate power supply (98900018101) into the cable. This is the same for both the wired and
wireless configurations.
Q. Is the wireless V450 Bluetooth?
A. Yes, wireless handheld unit (V450HDS36780001), uses Bluetooth communication to connect from
the handheld to the cradle. The Cradle is then connected into the system with one of the possible
configurations. However you may choose to connect the wireless handheld unit directly to a Bluetooth
host device. A video showing the Bluetooth to host connection can be found at:
https://automation.omron.com/en/us/video/player/21299
Q. Do I need the external battery charger?
A. In most wireless configurations, the cradle (12900093701) provides charging for the battery.
However if the handheld is directly connected to a host device over Bluetooth, then the external 4-slot
battery charger (98900018501) with power supply (98900018201) & cable (12900095901) is a good
option to re-charge the battery in the handheld.
/