Extron AXI 22 AT D User manual

Extron
Brand
Extron
Model
AXI 22 AT D
Category
Musical Equipment
Type
User manual
User Guide
AXI 22 AT D
Audio Products
Mixers and Processors
Audio Expansion Interface
68-2758-01 Rev. C
01 19
Safety Instructions
Safety Instructions • English
WARNING: This symbol, , when used on the product, is intended to
alert the user of the presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of electric shock.
ATTENTION: This symbol, , when used on the product, is intended
to alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website, www.extron.com.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer
darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind und
die einen elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in
der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in
den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.com.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa
al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con el
equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad
de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le
produit, signale à l’utilisateur la présence à l’intérieur du boîtier du
produit d’une tension électrique dangereuse susceptible de provoquer
un choc électrique.
ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,
signale à l’utilisateur des instructions d’utilisation ou de maintenance
importantes qui se trouvent dans la documentation fournie avec le
matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron, réf.
68-290-01, sur le site Extron, www.extron.com.
Istruzioni di sicurezza • Italiano
AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad
avvertire l’utente della presenza di tensione non isolata pericolosa
all’interno del contenitore del prodotto che può costituire un rischio di
scosse elettriche.
ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad
avvertire l’utente della presenza di importanti istruzioni di funzionamento
e manutenzione nella documentazione fornita con l’apparecchio.
Per informazioni su parametri di sicurezza, conformità alle normative,
compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento
alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo
68-290-01, sul sito web di Extron, www.extron.com.
Instrukcje bezpieczeństwa • Polska
OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu
poinformować użytkownika o obecności izolowanego i niebezpiecznego
napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie
porażenia prądem elektrycznym.
UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do
ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji
(obsługi) w literaturze, wyposażone w sprzęt.
Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji
wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne,
zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część
numer 68-290-01, na stronie internetowej Extron, www.extron.com.
Инструкция по технике безопасности • Русский
ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан
на продукте, предупреждает пользователя о наличии
неизолированного опасного напряжения внутри корпуса
продукта, которое может привести к поражению электрическим
током.
ВНИМАНИЕ: Данный символ, , если указан на продукте,
предупреждает пользователя о наличии важных инструкций
по эксплуатации и обслуживанию в руководстве,
прилагаемом к данному оборудованию.
Для получения информации о правилах техники безопасности,
соблюдении нормативных требований, электромагнитной
совместимости (ЭМП/ЭДС), возможности доступа и других
вопросах см. руководство по безопасности и соблюдению
нормативных требований Extron на сайте Extron: ,
www.extron.com, номер по каталогу - 68-290-01.
安全说明 • 简体中文
警告： 产品上的这个标志意在警告用户该产品机壳内有暴露的危险 电压，
有触电危险。
注意： 产品上的这个标志意在提示用户设备随附的用户手册中有
重要的操作和维护(维修）说明。
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容，敬请访问 Extron 网站 , www.extron.com，参见
Extron 安全规范指南，产品编号 68-290-01
。
安全記事 • 繁體中文
警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著
可能會導致觸電之風險的未絕緣危險電壓。
注意 若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有
重要的操作和維護（維修）説明。
有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資
訊，請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規
遵守手冊》，準則編號 68-290-01。
安全上のご注意
• 日本語
警告: この記号 が製品上に表示されている場合は、筐体内に絶縁されて
いない高電圧が流れ、感電の危険があることを示しています。
注意:この記号 が製品上に表示されている場合は、本機の取扱説明書に
記載されている重要な操作と保守(整備)の指示についてユーザーの注意
を喚起するものです。
安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目に
つ い て は 、エ ク スト ロ ン の ウェブ サ イト www.extron.com よ り 『 Extron Safety
and Regulatory Compliance Guide』 ( P/N 68-290-01) をご覧ください。
안전 지침 • 한국어
경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와
있는 주요 운영 및 유지보수(정비) 지침을 경고합
니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에
대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및
규제 준수 안내서, 68-290-01 조항을 참조하십시오.
Copyright
© 2019 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks
®
, registered service marks(
SM
), and trademarks(
TM
) are the property of RGBSystems, Inc. or Extron
Electronics (see the current list of trademarks on the
Terms of Use page at www.extron.com):
Registered Trademarks
(®)
AVTrac, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, GlobalViewer, Global Configurator, Global
Scripter, Hideaway, Inline, IP Intercom, IP Link, Key Minder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA, PlenumVault, PoleVault, PowerCage,
PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, System INTEGRATOR, TeamWork, TouchLink, V-Lock, VersaTools, VoiceLift, VN-Matrix,
WallVault, WindoWall, XTP, and XTP Systems
Registered Service Mark
(SM)
: S3 Service Support Solutions
Trademarks
(
™
)
AAP, AFL (Accu-RATE Frame Lock), ADSP - Advanced Digital Sync Processing, Auto-Image, CableCover, CDRS - Class D Ripple Suppression, DDSP
(Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), Driver Configurator, DSP Configurator, DSVP (Digital Sync Validation Processing),
eLink, EQIP, EverLast, FastBite, FOX, FOXBOX, HyperLane, IP Intercom HelpDesk, MAAP, MicroDigital, Opti-Torque, ProDSP,
QS-FPC - QuickSwitch Front Panel Controller, Room Agent, Scope-Trigger, ShareLink, SIS (Simple Instruction Set), Skew-Free, SpeedNav, Triple-Action
Switching, True4K, Vector™ 4K, WebShare, XTRA, ZipCaddy, and ZipClip
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause interference. This interference must be corrected at the expense of the user.
NOTE: For more information on safety guidelines, regulatory compliances, EMI/
EMF compatibility, accessibility, and related topics, see the “Extron Safety and
Regulatory Compliance Guide” on the Extron website.
VCCI-A Notice
この装置は、クラスＡ情報技術装置です。 この装置を家庭環境で使用すると、電波妨害を引き
起こすことがあります。 その場合には使用者が適切な対策を講ずるよう要求されることがあります。
Ｖ
ＣＣI－Ａ
Conventions Used in this Guide
Notifications
The following notifications are used in this guide:
WARNING: Potential risk of severe injury or death.
AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.
ATTENTION:
• Risk of property damage.
•
Risque de dommages matériels.
NOTE: A note draws attention to important information.
TIP: A tip provides a suggestion to make working with the application easier.
Software Commands
NOTE: For commands and examples of computer or device responses used in this
guide, the character “0” (Extron Mono font Regular) is used for the number zero and
“O” is the capital letter “o.”
Computer responses and directory paths that do not have variables are written in the font
shown here:
Reply from 208.132.180.48: bytes=32 times=2ms TTL=32
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons, tabs, and field names are
written in the font shown here:
From the File menu, select New.
Click the OK button.
This Attention box is for
XTP and DTP ONLY,
delete for all others
Delete this entire NOTE if
the above ATTENTION IS
USED FOR XTP AND DTP
PRODUCTS. DELETE the
FIRST paragraph if NOT
TP. The second paragraph
is required if the Attention
is not used (it is duplicate
information).
Delete this entire section if
the product does not have
a battery.
Specifications Availability
Product specifications are available on the Extron website, www.extron.com.
Extron Glossary of Terms
A glossary of terms is available at http://www.extron.com/technology/glossary.
aspx.
vAXI 22 AT D • Table of Contents
Contents
Introduction............................................................ 1
About this Guide ................................................. 1
About the AXI22AT D ........................................ 1
Features ............................................................. 2
AXI22AT D Application Diagrams ...................... 3
Installation and Operation .................................. 5
System Configuration ......................................... 5
Rear Panel Features and Cabling ........................ 5
Front Panel Features ......................................... 11
Indicator LEDs .............................................. 12
Setting Phantom Power .................................... 13
Setting the Gain Controls .................................. 14
Resetting ....................................................... 14
Dante Controller
Configuration and Operation
.......................... 15
Connecting the AXI 22 AT D to a Network ........ 15
Creating a Physical Dante Network ................... 16
Downloading and Installing Dante Controller
for Windows .................................................... 16
Starting Dante Controller .................................. 20
Dante Network Setup ....................................... 21
Renaming a Dante Device............................. 22
Finding a Dante Device IP Address ............... 25
Identifying a Physical Device ......................... 25
Renaming a Receiver or Transmitter.............. 26
Dante Operation ............................................... 29
Routing Devices............................................ 29
Disconnecting Inputs from Outputs ............... 31
Dante Troubleshooting ...................................... 32
Mounting the AXI 22 AT D ................................ 34
AXI 22 AT D • Table of Contents vi
AXI 22 AT D • Introduction 1
Introduction
This section provides an overview of this guide and the features of the Extron AXI 22AT D
Audio Expansion Interface. Topics include:
• About this Guide
• About the AXI 22 AT D
• Features
• AXI 22 AT D Application Diagrams
About this Guide
This guide contains installation, configuration, and operation information for the Extron
Electronics AXI22 AT D Audio Expansion Interface. In this guide, the terms “AXI,” “AXI22,”
“AXI 22 AT D,” and “interface” are used interchangeably to refer to the AXI22AT D.
About the AXI22AT D
The Extron AXI 22 AT D Audio Expansion Interface is a single-gang decorator-style audio
interface for integrating two mic/line sources onto a Dante-enabled audio system. It features
two XLR audio inputs and switchable 48 volt phantom power for connecting and powering
condenser microphones, plus gain controls for each input. The AXI 22 AT D also features
two line outputs on the back for routing any two Dante channels from the network to an
amplifier, or connecting into an optional secondary wallplate with two XLR outputs or RCA
outputs.
The AXI 22 AT D interfaces with any Dante-equipped audio processor, such as an Extron
DMP 128 AT, over a standard local area network, and can be powered through Power
over Ethernet (PoE) using Extron XTP PI 100 and XTP PI 400 power injectors, network
switches equipped with PoE, or midspan PoE injectors. This allows a single network cable
connection for bidirectional audio and power from a central equipment rack.
The AXI 22 AT D accepts two analog mic/line sources, and digitizes them for output via
Dante. It is connected into a Dante network over Ethernet using standard IP networking
protocols, avoiding the need for pulling long analog mic/line cables from an audio processor
to each wall, floor box, or furniture location. An audio system can be designed with AXI 22
AT D wallplate interfaces throughout a large facility, each connecting back into a central
equipment location over a standard network infrastructure.
The unit mounts in a standard 1-gang US opening using a decorator-style wallplate
(included), which is available in black or white. For information on mounting procedures, see
Mounting the AXI 22 AT D, beginning on page34.
AXI 22 AT D • Introduction 2
Features
• Inputs — Two balanced mic/line level inputs on 3-pin XLR connectors for transmitting
audio to a Dante™ network
• Outputs — Two balanced or unbalanced line outputs on a 3.5 mm, 6-pole captive
screw connector are located on the rear panel. They can be used for routing any
two audio channels from the Dante network to an amplifier, or for connecting into an
optional secondary Extron wallplate with two XLR or RCA outputs. The XLR outputs are
ideal for recording, or an ALS - assistive listening system.
• Phantom Power — Each input includes selectable 48-volt phantom power and a
rotary, detented gain control.
• Dante audio networking — Like all Dante-equipped audio products, the AXI 22 AT
D provides scalability for creating larger audio systems over a local area network using
standard Internet protocols.
• Converters — Professional, studio grade 24-bit analog-to-digital and digital-to-analog
converters fully preserve the integrity of the original audio signal. The sample rate is
selectable, up to 96 kHz.
• Removable cover plate — Input gain and phantom power controls are located behind
a removable cover plate on the front panel, which conceals all controls to prevent
tampering.
• Secondary wallplates — Optional Extron WPD 102 XLRM and WPD 102 RCA
secondary decorator-style wallplates with two XLR or RCA outputs can be connected
to the line outputs of the AXI 22 AT D to provide a two-gang wall installation with XLR
audio inputs and XLR or RCA outputs.
• Power over Ethernet — Power over Ethernet allows the AXI 22 AT D to receive power
over a single Ethernet cable, eliminating the need for a local power supply
•
Single-gang decorator
-style wallplate — The included single-gang decorator
-
style
wallplate is available in black or white to blend with a range of environments.
•
Power supply — An optional, energy-efficient external universal power supply
(replacement part number 70-775-01) provides worldwide power compatibility, with
high demonstrated reliability and low power consumption for reduced operating costs.
• Ethernet monitoring and control — Ethernet control enables proactive monitoring
and management of the AXI22AT D over a LAN, WAN, or the Internet, using standard
TCP/IP protocols.
AXI 22 AT D • Introduction 3
AXI22AT D Application Diagrams
100-240V ~ 0.7A MAX
50/60 Hz
LAN
EXP
RS-232
Tx Rx G
RESET
MIC +48V
5678
1234
8
4 1
12345G 6
1234
78910 G
11 12 13 14 15 G1617181920G
234
56 78
910
11 127
3
6
2
5
1
MIC/LINE INPUTS
OUTPUTS
DIGITAL I/O
REMOTE AT
DMP 128 AT
INPUT
1
INPUT
2
12
3
12
3
INPUT
1
INPUT
2
12
3
12
3
INPUT
1
INPUT
2
12
3
12
3
INPUT
1
INPUT
2
12
3
12
3
+6
+4
+2
0
-2
-4
-6
-12
-8
-20
-∞
GAIN
HPF LINE OUT REMOTE AT 70 V OUTPUT
NetPA 1001-70V AT
80 Hz
OFF
100-240V 0.5A MAX
STANDBY
G
CLASS 2 WIRING
50-60 Hz
RESET
LINK
Extron
AXI 22 AT D
Audio Expansion
Interface
Extron
DMP 128 AT
Digital Matrix Processor
Dante
Network
Extron
FF 220T
Plenum 600mm x 600mm
Flat Field Ceiling Speakers
Extron
NetPA 1001-70V AT
Audio Power Amplier
with Dante
Ethernet Ethernet
EthernetEthernetEthernetEthernet
Audio
A
udio Audio
Extron
AXI 22 AT D
Audio Expansion
Interface
AudioAudio
Extron
AXI 22 AT D
Audio Expansion
Interface
AudioAudio
Extron
AXI 22 AT D
Audio Expansio
n
Interface
AudioAudio
Figure 1. Typical AXI 22 AT D System
AXI 22 AT D • Introduction 4
100-240V ~ 0.7A MAX
50/60 Hz
LAN
EXP
RS-232
Tx Rx G
RESET
MIC +48V
5678
1234
8
4 1
12345G 6
1234
78910G
11 12 13 14 15 G1617181920G
234
56 78
910
11 127
3
6
2
5
1
MIC/LINE INPUTS
OUTPUTS
DIGITAL I/O
REMOTE AT
DMP 128 AT
+6
+4
+2
0
-2
-4
-6
-12
-8
-20
-∞
GAIN
HPF LINE OUT REMOTE AT 70 V OUTPUT
NetPA 1001-70V AT
80 Hz
OFF
100-240V 0.5A MAX
STANDBY
G
CLASS 2 WIRING
50-60 Hz
RESET
LINK
+6
+4
+2
0
-2
-4
-6
-12
-8
-20
-∞
GAIN
HPF LINE OUT REMOTE AT 70 V OUTPUT
NetPA 1001-70V AT
80 Hz
OFF
100-240V 0.5A MAX
STANDBY
G
CLASS 2 WIRING
50-60 Hz
RESET
LINK
+6
+4
+2
0
-2
-4
-6
-12
-8
-20
-∞
GAIN
HPF LINE OUT REMOTE AT 70 V OUTPUT
NetPA 1001-70V AT
80 Hz
OFF
100-240V 0.5A MAX
STANDBY
G
CLASS 2 WIRING
50-60 Hz
RESET
LINK
+6
+4
+2
0
-2
-4
-6
-12
-8
-20
-∞
GAIN
HPF LINE OUT REMOTE AT 70 V OUTPUT
NetPA 1001-70V AT
80 Hz
OFF
100-240V 0.5A MAX
STANDBY
G
CLASS 2 WIRING
50-60 Hz
RESET
LINK
INPUT
1
INPUT
2
12
3
12
3
INPUT
1
INPUT
2
12
3
12
3
INPUT
1
INPUT
2
12
3
12
3
INPUT
1
INPUT
2
12
3
12
3
HDMI IN
PWR HDMI HDCP
Extron
AXI 22 AT D
Audio Expansion
Interface
Extron
AXI 22 AT D
Audio Expansion
Interface
Extron
AXI 22 AT D
Audio Expansion
Interface
Extron
AXI 22 AT D
Audio Expansion
Interface
Extron
DMP 128 AT
Digital Matrix Processor
Dante
Network
Extron
CS 1226T
SpeedMount Ceiling Speaker System
Banquet Room
Local Closet
Central AV
Audio
Extron
NetPA 1001-70V AT
Audio Power Amplier
with Dante
Extron
NetPA 1001-70V AT
Audio Power Amplier
with Dante
Extron
NetPA 1001-70V AT
Audio Power Amplier
with Dante
Extron
NetPA 1001-70V AT
Audio Power Amplier
with Dante
Wall Panel
West
Wall Panel
East
Wall Panel
North
Wall Panel
South
Zone 4
Zone 3
Extron
CS 1226T
SpeedMount Ceiling Speaker System
Zone 2
Zone 1
Ethernet
Ethernet
Ethernet
Ethernet
Extron
XTP CrossPoint 1600
Modular Digital Matrix Switcher
Extron
XTP T HWP
101 D
Transmitter
Figure 2. AXI 22 AT D Banquet Hall Application
AXI 22 AT D • Installation and Operation 5
Installation and
Operation
This section describes the front and rear panel features and the rear panel connections. It
also provides procedures for installing the Dante Controller software. The following topics
are discussed:
• System Configuration
• Rear Panel Features and Cabling
•
Fr
ont Panel Features
•
Resetting
System Configuration
Dante Controller for Windows from Audinate is required to select and route Dante transmit
and receive channels to all connected Dante-compatible devices (see Downloading and
Installing Dante Controller for Windows on page 16).
Rear Panel Features and Cabling
AXI 22 AT D
AT (PoE)
OUTPUTS
1
POWER
12V
0.3A
MAX
2
DD
AA
CC
BB
DD
Top
Rear
A
Power Input Connector
C
Line Output 2 Connector
B
Line Output 1 connector
D
AT (PoE) port connector
Figure 3. AXI22CAT Rear Panel
AXI 22 AT D • Installation and Operation 6
A
Power input connector — If not using PoE, connect an optional 12VDC power
supply (part number 70-775-01) to this captive screw connector and plug the power
cord into the IEC connector on the power supply. The amber Power LED behind the
front panel (visible around the input connectors) blinks while the unit is booting, then
turns off when boot-up is complete. If there is no network connection, the LED lights
steadily (see Indicator LEDs on page 12 for more information).
WARNING: The two power cord wires must be kept separate while the power supply
is plugged in. Remove power before wiring.
AVERTISSEMENT :
Les deux cor
dons d’alimentation doivent être tenus à l’écart
l’un de l’autre quand l’alimentation est branchée. Couper l’alimentation avant de faire
l’installation électrique.
ATTENTION:
•
Do not connect any exter
nal power supplies until you have read the Attention
notifications on the next page.
•
Ne branchez pas de sour
ces d’alimentation externes avant d’avoir lu les mises
en garde de la page suivante.
Rear Panel
Power Receptacle
DC Power Cord
Captive Screw
Connector
Ground
all devices.
External
Power Supply
12 VDC, 1 A max.
– Return
+12 VDC input
Ridged
Smooth
1A MAX
100-240V 50-60Hz
Figure 4. Connecting the External Power Supply
AXI 22 AT D • Installation and Operation 7
ATTENTION:
•
Always use a power supply provided by or specified by Extron. Use of an
unauthorized power supply voids all regulatory compliance certification and may
cause damage to the supply and the end product.
• Utilisez toujours une source d’alimentation fournie ou recommandée par Extron.
L’utilisation d’une source d’alimentation non autorisée annule toute conformité
réglementaire et peut endommager la source d’alimentation ainsi que le produit
final.
• This product is intended for use with a UL Listed power source marked “Class 2” or
“LPS” and rated 12VDC, minimum 1.0 A. or 48 VDC (PoE), minimum 0.35 A.
• Ce produit est destiné à une utilisation avec une source d’alimentation listéeUL
avec l’appellation «Classe2» ou «LPS» et normée 12Vcc, 1,0A minimum ou
48Vcc (PoE), 0,35A minimum.
• Extron power supplies are certified to UL/CSA 60950-1 and are classified as LPS
(Limited Power Source). Use of a non-LPS or unlisted power supply will void all
regulatory compliance certification.
• Les sources d’alimentation Extron sont qualifiées UL/CSA60950-1 et sont
classéesLPS(LimitedPowerSource). L’utilisation d’une source d’alimentation
non-listée ou non-listéeLPS annulera toute certification de conformité
réglementaire.
• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling
spaces or in wall cavities. The power supply is to be located within the same vicinity
as the Extron AV processing equipment in an ordinary location, Pollution Degree 2,
secured to the equipment rack within the dedicated closet, podium, or desk.
• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une
utilisation dans les espaces d’aération ou dans les cavités murales. La source
d’alimentation doit être située à proximité de l’équipement de traitement audiovisuel
dans un endroit ordinaire, avec un degré2 de pollution, fixé à un équipement de
rack à l’intérieur d’un placard, d’une estrade, ou d’un bureau.
• The installation must always be in accordance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical
Code part 1, section 16.
• Cette installation doit toujours être en accord avec les mesures qui s’applique
au National Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical
Code, partie1, section16.
• The power supply shall not be permanently fixed to building structure or similar
structure.
• La source d’alimentation ne devra pas être fixée de façon permanente à une
structure de bâtiment ou à une structure similaire.
• The length of the exposed wires in the stripping process is critical. The ideal length
is 3/16 inches (5 mm). If the wires are any longer, the exposed wires may touch,
causing a short circuit between them. If they are any shorter, the wires can be easily
pulled out even if tightly fastened by the captive screws.
• La longueur des câbles exposés est primordiale lorsque l’on entreprend de les
dénuder. La longueur idéale est de 5mm (3/16inches). S’ils sont un peu plus
longs, les câbles exposés pourraient se toucher et provoquer un court circuit. S’ils
sont un peu plus courts, ils pourraient sortir, même s’ils sont attachés par les vis
captives.
NOTE: Do not tin the wires. Tinned wire does not hold its shape and can become
loose over time.
AXI 22 AT D • Installation and Operation 8
B
and
C
Analog audio output connectors — The 3.5 mm, 6-pole captive screw
connector contains two analog connectors for audio line output. Connect these mono
or stereo line outputs directly to an amplifier, recorder, or other audio device, or to an
output wallplate containing two XLR or RCA connectors. These outputs are listed as
receivers on the Dante network (see Dante Operation on page 29). Dante Controller
can route signals from other devices to these outputs. Wire the connector as shown in
figure 5.
Do not tin the wires!
(5 mm) MAX.
3 "
16
Balanced Output
Unbalanced Output
+
–
+
–
Tip
Ring
Tip
Ring
Sle
eves
Tip
No Ground Here
No Ground Here
Tip
Sleeves
Sle
eves
Sleeves
+
–
+
–
Figure 5. Analog Output Connectors
An adapter cable is available for more convenient connection of the outputs to
equipment using RCA patch cables. Connect the 5-pole CSR 6 cable as shown in
figure 6.
ATTENTION:
• For unbalanced audio outputs, connect the sleeves to the ground contact. DO
NOT connect the sleeves to the negative (-) contacts.
•
Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne P
AS
connecter les manchons aux contacts négatifs (–).
5-pole CSR 6
DO NOT
Connect Her
e
OUTPUTS
1
2
Figure 6. Connecting a 5-pole Audio Connector
Using a WPD 102 wallplate:
To provide additional outputs for the AXI 22, you can connect the AXI rear panel line
outputs to an Extron WPD 102 XLRM or WPD 102 RCA decorator-style wallplate. The
WPD 102 XLRM has two male XLR audio connectors and the WPD 102 RCA has two
female RCA connectors. Both are single-gang modules with a captive screw plug on
the back.
An AXI 22 and WPD 102 can be set up as a two-gang wall installation with XLR audio
inputs and XLR or RCA outputs. They also provide local wall, floor box, or furniture-
mounted connectivity for any audio system.
Figure 7 on the next page shows an example of a two-gang AXI and WPD 102
wallplate installation.
AXI 22 AT D • Installation and Operation 9
INPUT
1
INPUT
2
12
3
12
3
INPUT
1
INPUT
2
12
3
12
3
INPUT
1
INPUT
2
12
3
12
3
INPUT
1
INPUT
2
12
3
12
3
OUTPUT 1
21
3
21
3
OUTPUT 2
Extron
DMP 128 AT
Digital Matrix Processor
Dante
Network
Extron
AXI 22 AT D
Audio
Expansion
Interface
Extron
WPD 102 XLRM
Pass-Through
Wallplate
Extron
AXI 22 AT D
Audio
Expansion
Interface
Extron
AXI 22 AT D
Audio
Expansion
Interface
Extron
AXI 22 AT D
Audio Expansion
Interface
1
00
-
2
4
0V
~
0
.7
A
MAX
5
0
/
60 Hz
EXP
Tx
R
x
G
G
G
R
E
S
E
T
5
6
7
8
1
2
3
4
8
4
1
1
2
3
4
5
G
6
4
7
8
9
1
0
G
1
11
12
2
1
3
1
14
15
G
1
6
17
1
8
19
9
20
G
4
5
8
9
10
11
12
7
3
6
2
5
1
MIC/LINE INPUTS
MIC/LINE
INPUTS
OUTPUTS
OUTPUTS
DIGITAL I/O
DIGITAL
I/O
REMOTE
REMOTE
DMP 128
C
AT
Figure 7. Using the AXI with a WPD 102 XLRM
D
AT (PoE) port connector — This single RJ-45 Ethernet connector supports digital
audio transport (AT) and communications, providing a connection to the Dante network.
Using a straight-through Ethernet cable, connect the AXI to a network via the RJ-45 AT
port. On the AT connector:
• A steady green (Link) LED indicates that the jack is connected properly to
the network.
• A blinking amber (Activity) LED indicates data activity on the connection.
ATTENTION:
• The AXI 22 AT D can use a 12 VDC desktop power supply and is also Power over
Ethernet (PoE 802.3at, class3) compliant. Do not connect either power supply
before reading the Attention notifications on
page 7 or page 10.
• Le AXI 22 AT D peut utiliser une source d’alimentation externe 12 Vcc, et est
également compatible avec l’alimentation POE via Ethernet (PoE802.3at, classe 3).
Ne branchez pas de sources d’alimentation externes avant d’avoir lu les mises en
garde dans la section «PowerSupply» sur
page7 ou page10.
Connecting Power over Ethernet (PoE): The AXI 22 AT D accepts power
over Ethernet through this LAN port, which conforms to the 802.3at standard. To
connect PoE to the AXI, you can use a midspan power injector such as the Extron
XTP PI 100 (part number 60-1233-01) or XTP PI 400 (60-1298-01) or any network switch
that is equipped with PoE. Both an external power supply and a PoE injector or switch
can be connected to the AXI simultaneously. The unit uses PoE when it is available but
can switch seamlessly to the external power supply if the PoE connection is dropped.
AXI 22 AT D • Installation and Operation 10
ATTENTION:
•
The AXP 22 AT D is intended for connection to a Power over Ethernet circuit for
intra-building use only and are considered to be part of a Network Environment 0
per IEC TR62101.
• Le AXP 22 AT Dest conçu pour une connexion à un circuit PoE pour une utilisation
intérieure seulement et est considéré comme faisant partie d’un environnement
réseau 0 par IECTR62101.
• Always use a power supply provided by or specified by Extron. Use of an
unauthorized power supply voids all regulatory compliance certification and may
cause damage to the supply and the end product.
• Utilisez toujours une source d’alimentation fournie ou recommandée par Extron.
L’utilisation d’une source d’alimentation non autorisée annule toute conformité
réglementaire et peut endommager la source d’alimentation ainsi que le produit
final.
• This product is intended for use with a UL Listed power source marked “Class 2” or
“LPS” and rated 12VDC, minimum 1.0 A. or 48 VDC (PoE), minimum 0.35 A.
• Ce produit est destiné à une utilisation avec une source d’alimentation listéeUL
avec l’appellation «Classe2» ou «LPS» et normée 12Vcc, 1,0A minimum ou
48Vcc (PoE), 0,35A minimum.
• Extron power supplies are certified to UL/CSA 60950-1 and are classified as LPS
(Limited Power Source). Use of a non-LPS or unlisted power supply will void all
regulatory compliance certification.
• Les sources d’alimentation Extron sont qualifiées UL/CSA60950-1 et sont
classéesLPS(LimitedPowerSource). L’utilisation d’une source d’alimentation
non-listée ou non-listéeLPS annulera toute certification de conformité
réglementaire.
• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling
spaces or in wall cavities. The power supply is to be located within the same vicinity
as the Extron AV processing equipment in an ordinary location, Pollution Degree 2,
secured to the equipment rack within the dedicated closet, podium, or desk.
• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une
utilisation dans les espaces d’aération ou dans les cavités murales. La source
d’alimentation doit être située à proximité de l’équipement de traitement audiovisuel
dans un endroit ordinaire, avec un degré2 de pollution, fixé à un équipement de
rack à l’intérieur d’un placard, d’une estrade, ou d’un bureau.
• Power over Ethernet (PoE) is intended for indoor use only. It is to be connected only
to networks or circuits that are not routed to the outside plant or building.
• L’alimentation via Ethernet (PoE) est destinée à une utilisation en intérieur
uniquement. Elle doit être connectée seulement à des réseaux ou des circuits qui
ne sont pas routés au réseau ou au bâtiment extérieur.
• The installation must always be in accordance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical
Code part 1, section 16.
• Cette installation doit toujours être en accord avec les mesures qui s’applique
au National Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical
Code, partie1, section16.
• The power supply shall not be permanently fixed to building structure or similar
structure.
• La source d’alimentation ne devra pas être fixée de façon permanente à une
structure de bâtiment ou à une structure similaire.
AXI 22 AT D • Installation and Operation 11
To use a power injector: Connect a straight-through Ethernet cable to the power supply
and a switch or router. This cable carries network information from the switch or router to
the power supply input. A second straight-through cable carries the network information and
48VDC power from the power supply to the AXI. Connect the IEC power cord to a 100 VAC
to 240 VAC, 50-60 Hz power source.
Figure 8 shows the Extron XTP PI 100. Your power injector may look different.
100-240V
~
50-60Hz
0.4A MAX
XTP
PWR
XTP PWR
To network switchTo AXI 22 AT D
Figure 8. Connecting a Power Injector to AXI 22
For instructions on installing, connecting, and using the power injector, see the
documentation provided by the manufacturer. For the Extron XTP PI power injectors, user
and installation guides are available at
www.extron.com.
Front Panel Features
48V
1
2
R
48V
0dB
5
10
15
20
25dB
30
35
40
45
0dB
5
10
15
20
25dB
30
35
40
45
D
F
G
E
B
C
H
INPUT
1
INPUT
2
Extron
A
Faceplate Removed
Faceplate Attached
A
Faceplate
E
Mic/Line Input 2
B
Mic/Line Input 1
F
Input 2 Phantom Power switch
C
Input 1 Gain Control
G
Input 2 Gain Control
D
Input 1 Phantom Power switch
H
Reset button
Figure 9. AXI 22 AT D Front Panel
NOTE: Before setting the front panel controls, you must remove the faceplate (
A
).
AXI 22 AT D • Installation and Operation 12
A
Faceplate — This metal plate covers the front panel gain, reset, and
Phantom Power controls, protecting them from tampering.
The AXI is delivered with this plate fastened in place by one small
screw that is located between the two input connectors (see
1
in
the illustration at right). To access the front panel controls, remove this
screw and lift the faceplate off. Replace the faceplate before mounting
and attaching the wallplate (see Mounting the AXI 22 AT D on
page 34).
B
Input 1 — This female XLR connector accepts balanced and
unbalanced mic/line audio input.
C
Input 1 Gain Control — Rotate this recessed,10-position rotary selector to increase
or decrease the input 1 gain (see Setting the Gain Controls on page 14).
D
Input 1 Phantom Power switch — This recessed toggle switch enables and
disables Phantom Power for input 1. Before using this switch, see the Phantom Power
ATTENTION notices on page 13.
E
Input 2 — This female XLR connector accepts balanced and unbalanced mic/line
audio input.
F
Input 2 Phantom Power switch — This recessed toggle switch enables and
disables phantom power for input 2. Before using this switch, see the Phantom Power
ATTENTION notices on page 13.
G
Input 2 Gain Control — Rotate this recessed,10-position rotary selector to increase
or decrease the input 2 gain (see Setting the Gain Controls).
H
Reset Button — Using a stylus or small screwdriver, press and release this button
to reset the unit to factory defaults. This reset includes Dante settings such as device
name, IP address, channel names, and audio format. Gain and Phantom Power settings
are not affected.
Indicator LEDs
The AXI 22 has two sets of LEDs, one amber (Power LED) and one green (Phantom Power
LED), located behind the front panel and above each XLR input. The LEDs are visible
through the tops of the two XLR input connectors.
Power LEDs
The two amber Power LEDs light when power is applied to the unit. Each LED:
•
Blinks while the AXI is booting up.
•
Becomes unlit when the boot-up is complete.
•
Lights steadily if ther
e is no network connection.
•
Blinks if the AXI is in Identify mode (the Identify button on the Dante Controller
screen has been clicked). See Identifying a Physical Device on page 25 for more
information.
NOTE: If the green Phantom Power LEDs are lit when the AXI is placed in Identify
mode, they become unlit while the Power LED is blinking (Phantom Power remains
enabled).
Phantom Power LEDs
Each green Phantom Power LEDs lights when phantom power is enabled for the associated
input (see Setting Phantom Power on the next page). Phantom power is +48 VDC.
INPUT
1
INPUT
2
11
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43

Extron AXI 22 AT D User manual

Extron
Brand
Extron
Model
AXI 22 AT D
Category
Musical Equipment
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents