Clarion VRX928RVD Owner's manual

Category
TVs & monitors
Type
Owner's manual

Clarion VRX928RVD is a versatile car audio-video system that seamlessly integrates with your vehicle's entertainment system. It features a motorized 7-inch LCD screen for an immersive viewing experience, providing visual enjoyment for both audio and video content. Enjoy high-quality audio with the built-in amplifier and a wide range of connectivity options, including support for DVD changers and auxiliary audio/video sources.

Clarion VRX928RVD is a versatile car audio-video system that seamlessly integrates with your vehicle's entertainment system. It features a motorized 7-inch LCD screen for an immersive viewing experience, providing visual enjoyment for both audio and video content. Enjoy high-quality audio with the built-in amplifier and a wide range of connectivity options, including support for DVD changers and auxiliary audio/video sources.

VRX928RVD 71
English
Installation and Wire
connection manual
VRX928RVD
Installation and Wire connection manual
Contents
1. BEFORE STARTING ............................................................... 65
2. PACKAGE CONTENTS ........................................................... 65
3. GENERAL CAUTIONS ............................................................ 66
4. CAUTIONS ON INSTALLATION .............................................. 66
5. INSTALLING THE MAIN UNIT ................................................. 67
6. REMOVING THE MAIN UNIT .................................................. 69
7. CAUTIONS ON WIRING .......................................................... 69
8. WIRE CONNECTION .............................................................. 70
9. SAMPLE SYSTEMS ................................................................ 73
1. BEFORE STARTING
2. PACKAGE CONTENTS
1. This set is exclusively for use in cars with a
negative ground 12 V power supply.
2. Read these instructions carefully.
3. Be sure to disconnect the battery “- termi-
nal before starting. This is to prevent short
circuits during installation. (Figure 1)
Car battery
Figure 1
1 Main unit
2 Tuner Amp unit
3 Manuals
Owner’s manual & Installation manual
Warranty card
4 Power supply lead (For the main unit)
5 Power supply lead (For the tuner amp
unit)
6
Connection cord (Main unit Tuner amp unit)
7 Antenna extension cord
8 RGB connecting cord
9
Bag for accessories of the main unit (No. 1)
Flat head screw (M5 × 8) ............................ 4
Sems hexagonal bolt (M5× 8) ..................... 5
Electro tap
Machine screw (M4× 3)............................... 4
0
Bag for accessories of the main unit (No. 2)
Hook plate................................................... 2
Cord clamp
Rubber cap
Special screw
! Bag for accessories of tuner amp unit
Maunting bracket......................................... 2
Canoe clip ................................................... 4
Machine screw (M4 × 8).............................. 4
@ Universal mounting bracket
# Remote control unit
$ Battery
(for remote control unit)
% Outer Escutcheon
¥ DCP Case
72 VRX928RVD
English
Installation and Wire
connection manual
3. GENERAL CAUTIONS
4. CAUTIONS ON INSTALLATION
1. Do not open the case. There are no user ser-
viceable parts inside. If you drop anything
into the unit during installation, consult your
dealer or an authorized CLARION service
centre.
2. Use a soft, dry cloth to clean the case. Never
use a rough cloth, thinner, benzine, or alco-
hol, etc. For tough dirt, apply a little cold or
warm water to a soft cloth and wipe off the
dirt gently.
1. Prepare all articles necessary for installing
the main unit before starting.
2. This model is used with the LCD panel slid
forwards (shell loading system). On some
types of cars, the LCD panel may touch the
dashboard or shift lever, in which case it can-
not be installed. Check that the set will not
hamper operation of the shift lever before
choosing the place of installation.(Figure 2)
5. Use the enclosed screws for installation. Us-
ing other screws can cause damage. (Figure
4)
3. Install the unit within 30° of the horizontal
plane. (Figure 3)
4. If you have to do any work on the car body,
such as drilling holes, consult your car dealer
beforehand.
6. The source unit has mounting screw holes
for NISSAN (N marks) and TOYOTA (T
marks) vehicles.
Dashboard
Shift lever
Shift lever
(check that it does not
touch the LCD.)
Figure 2
Max. 30˚
Figure 3
Chassis Chassis
Damage
Max. 8 mm (M5 screw)
Figure 4
Figure 5
T
NNT
NT
VRX928RVD 73
English
Installation and Wire
connection manual
5. INSTALLING THE MAIN UNIT
Universal Mount
1. Place the universal mounting bracket into the
instrument panel, use a screwdriver to bend
each stopper of the universal mounting
bracket inward, then secure the stopper as
shown in Figure 6.
2. Wire as shown in Section 8.
3. Insert the main unit into the universal mount-
ing bracket until it locks.
4. Mount the outer escutcheon so that all the
hooks are locked.
Notes:
1) Some car models require special mounting kits
for proper installation. Consult your Clarion
dealer for details.
2) Fasten the front stopper securely to prevent the
main unit from coming loose.
Figure 6
• Console opening dimensions
Hole
Main unit
7-3/16" (182 mm)
2-1/16" (53 mm)
Screwdriver
Stoppers
Hole
Rear fastening hole (of vehicle)
Instrument panel
Rubber cap
Universal mounting bracket
Stoppers
2-Spring
Outer escutcheon
Note:
Set the outer escutch-
eon so that its metallic
part on the back side
fits the upper edge of
the main unit.
Special Screw
74 VRX928RVD
English
Installation and Wire
connection manual
This unit is designed for fixed installation in the
dashboard.
If the vehicle is equipped with a factory-installed
radio, install the main unit with the parts and
screws marked (). (Figure 8)
If the vehicle is not equipped with a factory-in-
stalled radio, obtain an installation kit to install
the main unit in the following procedure.
1. Remove the screws from both side of the
main unit. Then, at either side, lift the leaf
spring until the engaging claws are released
from the holes, and slide the spring to the di-
Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles)
rection of arrow to remove it. Repeat the
same for the other side to remove the
springs from the both sides. (Figure 7)
2. Secure the mounting brackets to the chassis
as shown in Figure 8. Holes are pre-tapped
for TOYOTA and NISSAN vehicles; modifica-
tion, such as drilling new holes, of the mount-
ing brackets may be required for other mod-
els.
3. Wire as shown in Section 8.
4. Secure the unit in the dashboard, and then
reassemble the dashboard and the centre
panel.
Note 1:
In some cases, the centre panel may require
some modification (trimming, filling, etc.).
Note 2: If a hook on the installation bracket inter-
feres with the unit, bend and flatten it with
a nipper or a similar tool.
2-Screw
2-Spring
4-Hexagonal screw (M5 × 8)
Main Unit
Figure 7
Main Unit
Screwdriver
Engagin claw
Mounting bracket
(1 pair for the left and right sides)
Pocket
Centre Panel (Note 1)
Note 2
Figure 8
: The screws with this mark are
enclosed in this set.
:The parts and screws with this mark
are used to install radio or included in
the installation kit.
VRX928RVD 75
English
Installation and Wire
connection manual
7. CAUTIONS ON WIRING
1. Be sure to turn the power off before wiring.
2. Be particularly careful where you route the
wires.
Keep them well away from the engine, and
exhaust pipe, etc. Heat may damage the
wires.
3. If the fuse should blow, check to see if the
wiring is correct.
If it is, replace the fuse with a new one with
the same amperage rating as the original.
4. To replace the fuse, remove the old fuse of
the power supply lead and insert the new
one. (Figure10)
Power supply lead for the tuner amp unit : 15A
FUSE
Power supply lead for the main unit : 3A FUSE
After the connection, fix the lead by a clamp or
insulation tape for protection.
CAUTION
Figure 10
1. When the rear of the main unit has been se-
cured with the method shown in Figure 6 un-
fasten the special screw.
2. Remove the outer escutcheon.
3. Insert the hook plate between the spring and
the universal mounting bracket, fit tab B of
the spring into hole A of the hook plate, then
6. REMOVING THE MAIN UNIT
pull the main unit out by the hook plate. (In-
sert both the right and left edges of the hook
plate.) (Figure 9)
Note:
Keep the hook plate. You cannot remove the
main unit without disengaging the hook plate.
Universal mounting bracket
2-Hook plate
Outer escutcheon
Instrument panel
Spring
Main
Unit
AB
Figure 9
Fuse
Fuse holder
Note:
There are various types of fuse holder. Do not
let the battery side touch other metal parts.
76 VRX928RVD
English
Installation and Wire
connection manual
Securely connect to the
metal part of the car with a
screw, etc.
CeNET cable (Sold separately)
CeNET
terminal
Reset switch
Front audio output (input) terminal L+R (RCA) 6
Non Fader output terminal L+R (RCA)
VISUAL 1 video input (RCA)/
DVD changer input (RCA)
TV TUNER input (RCA)
Top view of the
tuner amp unit
VIDEO output (RCA) 7
VISUAL 1 audio input
terminal L+R (RCA)
Rear audio output (input) terminal L+R (RCA) 6
Power supply lead
Power supply lead
RGB terminal
RGB connecting cord
(provided with this unit)
Earth (Ground) cord
Choke coil
Main power supply cord
Black
Yellow
Fuse
5.1 ch Surround Decoder select switch 5
Radio antenna jack 4
NAVI terminal 9
CCD/VISUAL 2 terminal 8
Connection cord
(provided with this unit)
Main unit
8. WIRE CONNECTION
VRX928RVD 77
English
Installation and Wire
connection manual
5
2
2
3
B-1
B-6
B-5
B-7
B-8
B-4
B-3
B-2
A-4
A-6
A-8
A-7
4
A-5
2
2
2
1
A-1
1: When the unit is installed in a 1998 or later Volkswagen model, make sure to interrupt the
<<Remote>> output. Disconnect the <<blue/white>> wire and insulate the front ends of this lead.
A breakdown may occur if the lead is not disconnected, or front ends are not insulated.
2: In certain vehicles - Volkswagen/Opel/Vauxhall - it is necessary to exchange the accessory
<<Red>> and the main power <<Yellow>> connection, to avoid overload and loss of memory.
3: Connecting the PHONE MUTE Terminal
The lead included with the unit must be connected to the specified position of the vehicle’s
connector in order to use the triggered audio mute for cellular telephones function.
4: Use the attached extension lead when necessary. (Provided with this unit)
Note : Before making any installation, disconnect the car battery - (negative) cable.
5: If a 5.1 ch Surround Decoder (DVH923, sold separately) is connected and the amp of this unit is
used, set the select switch to “LINE IN”. Then the AUDIO OUT (IN) terminal of the Tuner Amp
Unit is only available for audio input, not outputting the audio.
6: Connect to a separately sold external amplifier with a separately sold RCA cord (L, R).
Note : When the 5.1 ch Surround Decoder is connected, these terminals are only available for audio input.
7: Connect to a Rear View Monitor (sold separately) for the rear seat.
8: Connect to separately sold VTR equipment with a separately sold connection cord or CCD
camera (Sold separately).
9: Connect to a separately sold navigation device.
(LINE IN) D N (LINE OUT)
No. Description
REAR RIGHT
+
REAR RIGHT
-
FRONT RIGHT
+
FRONT RIGHT
-
FRONT LEFT
+
FRONT LEFT
-
REAR LEFT
+
REAR LEFT
-
SPEED PULSE
+12 V MAIN POWER (2)
AUTO ANTENNA (1)
ILLUMINATION
+12 V ACCESSORY (2)
GROUND
1 Spare terminal (Black)
2 Phone terminal (Brown) (3)
3 Spare terminal (Yellow)
4 ISO CONNECTOR
5 Parking brake (Bright Green)
B-1
B-2
B-3
B-4
B-5
B-6
B-7
A-4
A-5
A-6
A-7
A-8
B-8
A-1
78 VRX928RVD
English
Installation and Wire
connection manual
Connecting the Accessories
Connection to the external amplifier
The external amplifier can be connected unless the 5.1 ch Surround Decoder is connected. For
detailed information, refer to the instruction manual of the 5.1 ch Surround Decoder.
Connection to the CCD camera for vehicle
The CCD camera for vehicle can be connected to CCD/VISUAL 2 terminal on the tuner amp unit.
For detailed information, refer to the instruction sheet or manual for the CCD camera.
Notes:
A power supply box (sold separately) is required for connection of the main unit and the CCD camera.
While the CCD camera is used, the navigation cannot be turned on.
The power supply box for camera CAA147 cannot be used. Please use the CAA188 instead.
If the specified lead of the cellular phone is connected to the phone mute
lead of the source unit, the audio mute is available when the cellular
telephone is used.
For audio mute setting in cellular telephone use, see page 63.
DAB (Digital Audio Broadcasting)
When the DAB is to be connected, use the CeNET connector. For detailed information, refer to the
instruction manual of the DAB.
For DAB connection, the DAH913 can only be connected. The DAH9500Z cannot be connected.
TV Tunner
When the TV TUNER is to be connected, connect the CeNET connector and RCA PIN (yellow). For
detailed information, refer to the instruction manual of the TV TUNER.
Connecting the parking brake lead
Connect the lead to parking brake lamp earth
in the meter panel.
Notes:
Connecting the parking brake lead to lamp earth
allows you to watch TV/VTR/DVD video/video
CD when the parking brake is engaged.
When the parking brake lead is not connected,
the monitor will stay off.
Parking brake
Parking brake lamp
+ lead to battery
Connect these three leads.
- cord
parking
brake signal
lead
Parking brake lead
(bright green)
VRX928RVD 79
English
Installation and Wire
connection manual
9. SAMPLE SYSTEMS
VRX928RVD
Tuner IN
VISUAL 2 IN
VISUAL 1 IN
VTR
(TTX7502z/
TTX7503z)
(VCZ628)
(DCZ628)
(NAX9500E)
CeNET
STAND
ALONE
TV tuner
CeNET cable
(included the TV tuner)
RCA video cable
(included the TV tuner)
Rear View
Monitor
RCA video cable (sold separately)
AV Adapter cable
(CCA-389,
sold separately)
DVD Changer
CD Changer
CeNET Y-adapter
(CCA-519-500,
sold separately)
Ferrite clamp
(Included the DVD changer)
RCA video cable (included the VCZ628)
CeNET Cable
(included the Changer)
Front
Speakers
Rear
Speakers
RGB cable
*1
(included the NAX9500E)
Navigation System
*1.When a video composite source is used, connect
it to the 8-pin Mini-DIN video jack. When a RGB
source is used, connect it to the 8-pin DIN RGB
jack. In case a CLARION navigation system is
used, connect it to both input.
*2.To enable the correct input, it is necessary to con-
figure the VRX928RVD as described on page 59.
Mini DIN(8P) Cable
*1
(included the
NAX9500E)
Set the [CENET/STAND ALONE]
switch to the [CeNET] position.
Tuner Amp Unit
Sample System 1
80 VRX928RVD
English
Installation and Wire
connection manual
Sample System 2
VRX925VD
CeNET
STAND
ALONE
Tuner IN
VISUAL 2 IN
VISUAL 1 IN
SLAVE
STAND
ALONE
Ferrite clamp
(Included the DVD changer)
(VCZ628)
VTR
CeNET
TV Tuner
Tuner Amp Unit
CeNET
cable
(included
the TV
tuner)
RCA video cable
(included the TV tuner)
CeNET DVD Changer
CeNET cable
(included the VCZ628)
5.1 ch Surround
Decoder(DVH923)
CeNET cable
(included the
DVH923)
Front
Speakers
4-Channel
Amplifier
Rear
Speakers
Center speaker
built-in amplifier
(SRK601)
Powered sub-woofer
built-in amplifier
(Black)
Digital optical fiber cable (included the DVH923)
RCA cable
(included the SRK601)
RCA cable
(sold separately)
RCA cable (sold separately)
Digital optical fiber cable
(
DCA-005/008, sold separately)
Set the [SLAVE/STAND ALONE]
switch to the [SLAVE] position.
Set the [CENET/STAND ALONE]
switch to the [CeNET] position.
(Glay)
(Glay)
RCA video cable (included the VCZ628)
AV Adapter cable
(CCA-389,
sold separately)
The diagram shows a 5.1 ch
surround system configuration using
an external amplifier.
VRX928RVD 81
English
Installation and Wire
connection manual
Sample System 3
A 5.1 ch surround system configuration is made using the built-in amplifier of the Tuner Amp Unit.
The diagram below shows the different part from Sample system 2.
(LINE IN)D
N(LINE OUT)
Tuner Amp Unit
5.1 ch Surround
Decoder(DVH923)
Front
Speakers
Rear
Speakers
Center speaker
built-in amplifier
(SRK601)
Powered sub-woofer
built-in amplifier
(Black)
RCA cable
(inclouded the SRK601)
RCA cable
(sold separately)
RCA cable (sold separately)
Set the [(LINE IN)D/N(LINE OUT)]
switch to the [(LINE IN)D] position.
82 VRX928RVD
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Clarion VRX928RVD Owner's manual

Category
TVs & monitors
Type
Owner's manual

Clarion VRX928RVD is a versatile car audio-video system that seamlessly integrates with your vehicle's entertainment system. It features a motorized 7-inch LCD screen for an immersive viewing experience, providing visual enjoyment for both audio and video content. Enjoy high-quality audio with the built-in amplifier and a wide range of connectivity options, including support for DVD changers and auxiliary audio/video sources.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI