Extron MSW 4SV rs User manual

Brand: Extron

Model: MSW 4SV rs

Category: Video switches

Type: User manual

This manual is also suitable for

68-1267-01 Rev. C

08 11

MSW 4V rs and MSW 4SV rs

User Guide

Switchers

Mini Video Switchers

This symbol is intended to alert the user of important operating and

maintenance (servicing) instructions in the literature provided with the

equipment.

This symbol is intended to alert the user of the presence of uninsulated

dangerous voltage within the product enclosure that may present a risk of

electric shock.

Caution

Read Instructions • Read and understand all safety and operating instructions before using the equipment.

Retain Instructions • The safety instructions should be kept for future reference.

Follow Warnings • Follow all warnings and instructions marked on the equipment or in the user information.

Avoid Attachments • Do not use tools or attachments that are not recommended by the equipment

manufacturer because they may be hazardous.

Warning

Power sources • This equipment should be operated only from the power source indicated on the product. This

equipment is intended to be used with a main power system with a grounded (neutral) conductor. The third

(grounding) pin is a safety feature, do not attempt to bypass or disable it.

Power disconnection • To remove power from the equipment safely, remove all power cords from the rear of the

equipment, or the desktop power module (if detachable), or from the power source receptacle (wall plug).

Power cord protection • Power cords should be routed so that they are not likely to be stepped on or pinched by

items placed upon or against them.

Servicing • Refer all servicing to qualiﬁed service personnel. There are no user-serviceable parts inside. To prevent

the risk of shock, do not attempt to service this equipment yourself because opening or removing covers may

expose you to dangerous voltage or other hazards.

Slots and openings • If the equipment has slots or holes in the enclosure, these are provided to prevent

overheating of sensitive components inside. These openings must never be blocked by other objects.

Lithium battery • There is a danger of explosion if battery is incorrectly replaced. Replace it only with the same or

equivalent type recommended by the manufacturer. Dispose of used batteries according to the instructions of

the manufacturer.

Ce symbole sert à avertir l’utilisateur que la documentation fournie avec le

matériel contient des instructions importantes concernant l’exploitation et la

maintenance (réparation).

Ce symbole sert à avertir l’utilisateur de la présence dans le boîtier

de l’appareil de tensions dangereuses non isolées posant des risques

d’électrocution.

Attention

Lire les instructions• Prendre connaissance de toutes les consignes de sécurité et d’exploitation avant d’utiliser

le matériel.

Conserver les instructions• Ranger les consignes de sécurité aﬁn de pouvoir les consulter à l’avenir.

Respecter les avertissements • Observer tous les avertissements et consignes marqués sur le matériel ou

présentés dans la documentation utilisateur.

Eviter les pièces de fixation • Ne pas utiliser de pièces de ﬁxation ni d’outils non recommandés par le fabricant

du matériel car cela risquerait de poser certains dangers.

Avertissement

Alimentations • Ne faire fonctionner ce matériel qu’avec la source d’alimentation indiquée sur l’appareil. Ce

matériel doit être utilisé avec une alimentation principale comportant un ﬁl de terre (neutre). Le troisième

contact (de mise à la terre) constitue un dispositif de sécurité : n’essayez pas de la contourner ni de la

désactiver.

Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger, déconnectez tous les cordons

d’alimentation de l’arrière de l’appareil ou du module d’alimentation de bureau (s’il est amovible) ou encore de

la prise secteur.

Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de manière à ce que personne ne

risque de marcher dessus et à ce qu’ils ne soient pas écrasés ou pincés par des objets.

Réparation-maintenance • Faire exécuter toutes les interventions de réparation-maintenance par un technicien

qualiﬁé. Aucun des éléments internes ne peut être réparé par l’utilisateur. Aﬁn d’éviter tout danger

d’électrocution, l’utilisateur ne doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le

retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.

Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des oriﬁces, ceux-ci servent à empêcher les

composants internes sensibles de surchauffer. Ces ouvertures ne doivent jamais être bloquées par des objets.

Lithium Batterie • Il a danger d’explosion s’il y a remplacment incorrect de la batterie. Remplacer uniquement

avec une batterie du meme type ou d’un type equivalent recommande par le constructeur. Mettre au reut les

batteries usagees conformement aux instructions du fabricant.

Safety Instructions • English

Consignes de Sécurité • Français

Sicherheitsanleitungen • Deutsch

Dieses Symbol soll dem Benutzer in der im Lieferumfang enthaltenen

Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung

(Instandhaltung) geben.

Dieses Symbol soll den Benutzer darauf aufmerksam machen, daß im Inneren

des Gehäuses dieses Produktes gefährliche Spannungen, die nicht isoliert sind

und die einen elektrischen Schock verursachen können, herrschen.

Achtung

Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden, sollten Sie alle Sicherheits-und

Bedienungsanleitungen genau durchlesen und verstehen.

Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit des Produktes sollten Sie

aufbewahren, damit Sie im Bedarfsfall darauf zurückgreifen können.

Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und Anleitungen auf dem Gerät oder in der

Benutzerdokumentation.

Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte, die nicht ausdrücklich vom Hersteller

empfohlen wurden, da diese eine Gefahrenquelle darstellen können.

Vorsicht

Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene Stromquelle betrieben werden.

Dieses Gerät wurde für eine Verwendung mit einer Hauptstromleitung mit einem geerdeten (neutralen) Leiter

konzipiert. Der dritte Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese sollte nicht

umgangen oder außer Betrieb gesetzt werden.

Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten Sie alle Netzkabel aus der

Rückseite des Gerätes, aus der externen Stomversorgung (falls dies möglich ist) oder aus der Wandsteckdose

ziehen.

Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im Weg liegen und niemand

darauf treten kann oder Objekte darauf- oder unmittelbar dagegengestellt werden können.

Wartung • Alle Wartungsmaßnahmen sollten nur von qualiziertem Servicepersonal durchgeführt werden. Die

internen Komponenten des Gerätes sind wartungsfrei. Zur Vermeidung eines elektrischen Schocks versuchen

Sie in keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines

elektrischen Schlags und/oder andere Gefahren bestehen.

Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist, dienen diese zur

Vermeidung einer Überhitzung der empndlichen Teile im Inneren. Diese Öffnungen dürfen niemals von

anderen Objekten blockiert werden.

Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird. Ersetzen Sie verbrauchte Batterien nur

durch den gleichen oder einen vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen

Sie verbrauchte Batterien bitte gemäß den Herstelleranweisungen.

Este símbolo se utiliza para advertir al usuario sobre instrucciones

importantes de operación y mantenimiento (o cambio de partes) que se

desean destacar en el contenido de la documentación suministrada con los

equipos.

Este símbolo se utiliza para advertir al usuario sobre la presencia de

elementos con voltaje peligroso sin protección aislante, que puedan

encontrarse dentro de la caja o alojamiento del producto, y que puedan

representar riesgo de electrocución.

Precaucion

Leer las instrucciones • Leer y analizar todas las instrucciones de operación y seguridad, antes de usar el

equipo.

Conservar las instrucciones • Conservar las instrucciones de seguridad para futura consulta.

Obedecer las advertencias • Todas las advertencias e instrucciones marcadas en el equipo o en la

documentación del usuario, deben ser obedecidas.

Evitar el uso de accesorios • No usar herramientas o accesorios que no sean especiﬁcamente recomendados

por el fabricante, ya que podrian implicar riesgos.

Advertencia

Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo de alimentación eléctrica

indicada en el mismo. La alimentación eléctrica de este equipo debe provenir de un sistema de distribución

general con conductor neutro a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no

puentearia ni eliminaria.

Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida de alimentación eléctrica

al equipo, desenchufar todos los cables de alimentación en el panel trasero del equipo, o desenchufar el

módulo de alimentación (si fuera independiente), o desenchufar el cable del receptáculo de la pared.

Protección del cables de alimentación • Los cables de alimentación eléctrica se deben instalar en lugares donde

no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos.

Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal calicado. En el interior no

hay partes a las que el usuario deba acceder. Para evitar riesgo de electrocución, no intentar personalmente la

reparación/mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes

peligrosos u otros riesgos.

Ranuras y aberturas • Si el equipo posee ranuras o oriﬁcios en su caja/alojamiento, es para evitar el

sobrecalientamiento de componentes internos sensibles. Estas aberturas nunca se deben obstruir con otros

objetos.

Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición incorrecta. Cambiar esta batería

únicamente con el mismo tipo (o su equivalente) recomendado por el fabricante. Desachar las baterías usadas

siguiendo las instrucciones del fabricante.

Instrucciones de seguridad • Español

安全须知 • 中文

这个符号提示用户该设备用户手册中有重要的操作和维护说明。

这个符号警告用户该设备机壳内有暴露的危险电压，有触电危险。

注意

阅读说明书 • 用户使用该设备前必须阅读并理解所有安全和使用说明。

保存说明书 • 用户应保存安全说明书以备将来使用。

遵守警告 • 用户应遵守产品和用户指南上的所有安全和操作说明。

避免追加 • 不要使用该产品厂商没有推荐的工具或追加设备，以避免危险。

警告

电源 • 该设备只能使用产品上标明的电源。设备必须使用有地线的供电系统供电。第三条线（

地线）是安全设施，不能不用或跳过。

拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后或桌面电源的电源线，或任何接到市电

系统的电源线。

电源线保护 • 妥善布线，避免被踩踏，或重物挤压。

维护 • 所有维修必须由认证的维修人员进行。设备内部没有用户可以更换的零件。为避免出现触

电危险不要自己试图打开设备盖子维修该设备。

通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止机内敏感元件过热。不要用任何东西

挡住通风孔。

锂电池 • 不正确的更换电池会有爆炸的危险。必须使用与厂家推荐的相同或相近型号的电池。按

照生产厂的建议处理废弃电池。

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15

of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired

operation.

The Class A limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the user guide, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be

required to correct the interference at his own expense.

NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with

the unit to ensure compliance with FCC emissions limits.

For more information on safety guidelines, regulatory compliances, EMI/EMF compliance, accessibility, and

related topics, click here.

Conventions Used in this Guide

In this user guide, the following are used:

TIP: A tip provides a suggestion to make working with the application easier.

NOTE: A note draws attention to important information.

CAUTION: A caution indicates a potential hazard to equipment or data.

WARNING: A warning warns of things or actions that might cause injury, death, or

other severe consequences.

Commands are written in the fonts shown here:

^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C

[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]

E X! *X1& *X2) *X2# * X2!

}

NOTE: For commands and examples of computer or device responses mentioned

in this guide, the character “0” is used for the number zero and “O”

represents the capital letter “o.”

Computer responses and directory paths that do not have variables are written in the

font shown here:

Reply from 208.132.180.48: bytes=32 times=2ms TTL=32

C:\Program Files\Extron

Variables are written in slanted form as shown here:

ping xxx.xxx.xxx.xxx —t

SOH R Data STX Command ETB ETX

Selectable items, such as menu names, menu options, buttons, tabs, and field names are

written in the font shown here:

From the File menu, select New.

Click the OK button.

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners

Contents

Introduction............................................................ 1

About the MSW 4V rs and MSW 4SV rs

Switchers ........................................................... 1

Features .............................................................. 1

Application Diagrams .......................................... 2

Installation Overview........................................... 3

Panel Features ........................................................ 4

Rear Panel Connections ...................................... 4

Front Panel Controls and Indicators ..................... 7

Input Selection ................................................ 7

Auto Switch Mode Controls and Indicators ..... 7

Mode Selection ................................................... 7

Output (Video) Mute........................................... 8

Vertical Interval Switching ................................... 8

Control Software ................................................... 9

Universal Switcher Control Program .................... 9

Installing the Software .................................... 9

Using the software ........................................ 10

Using the Help File ........................................ 11

Updating the Firmware ..................................... 11

Downloading the MSW 4V rs and 4SV rs

ﬁrmware ...................................................... 11

Downloading and installing the

Firmware Loader .......................................... 12

Using the control program to update the

ﬁrmware ...................................................... 12

Speciﬁcations ....................................................... 16

SIS Commands ..................................................... 18

Introduction to SIS ........................................... 18

Symbols Used in this Guide ............................... 19

Error Messages ................................................. 19

Command and Response Table for

SIS Commands ................................................ 20

Parts and Accessories ......................................... 21

Included Parts ................................................... 21

Optional Accessories ......................................... 21

Mounting .............................................................. 22

Tabletop Placement ........................................... 22

Rack Mounting the MSW 4V rs and

MSW 4SV rs .................................................... 22

Underwriters Laboratories Guidelines for

Rack Mounting ............................................ 22

Rack Mounting the MSW 4V rs and

MSW 4SV rs ................................................. 23

Under-desk Mounting the MSW 4V rs and

MSW 4SV rs ................................................. 23

MSW 4V rs and MSW 4SV rs • Contents v

MSW 4V rs and MSW 4SV rs • Contents vi

Introduction

This guide describes the function, installation and operation of the Extron MSW 4V rs

and MSW 4SV rs mini video switchers. Unless otherwise stated, the terms “MSW” and

“switcher” refer to both models.

About the MSW 4V rs and MSW 4SV rs Switchers

The Extron MSW 4V rs and MSW 4SV rs are four-input, two parallel output, mini video

switchers (MSWs).

The MSW 4V rs switches between a maximum of four NTSC, PAL, or SECAM composite

video inputs on female BNC connectors and produces two identical video outputs

on female BNC connectors (see figure 1 on page 2). The video output is a buffered,

composite signal.

The MSW 4SV rs switches four S-video (luminance [Y] and chrominance [C]) inputs on

4-pin mini DIN connectors. The selected S-video input is split, buffered, and output on two

connectors (see figure 2 on page 2):

• One S-video output on a 4-pin mini DIN connector

• One composite video output on a female BNC connector

These mini video switchers can be operated from the front panel or via a contact closure

device connected to the rear panel, such as an Extron CCR 204 Four-Button Contact

Closure Remote or an IR 102 Remote Control Kit. The MSW Series include RS-232

communication, allowing control via the Extron Simple Instruction Set (SIS

™

) or the

Universal Switcher Control Program software.

They also feature a front panel selectable auto switch mode that automatically switches to

the highest numbered input that has an active sync pulse present.

Features

Inputs — four female 4-pin mini DIN connectors for S-video or four female BNC

connectors for composite video

Outputs — one BNC and one 4-pin mini DIN for S-video or two BNC connectors for

composite video (both models feature two parallel outputs for simultaneous monitor and

projector viewing)

Video Mute — the video output can be muted using front panel controls

Serial control — through an RS-232 port

Video compatibility — with NTSC, PAL, and SECAM video formats

Non-volatile memory — Retains unit settings after power loss

Firmware upgrades — available for download from the Extron Website.

Remote control — through contact closure

Ability to detect an active signal

Built-in video encoder (MSW 4SV rs model only) — for composite video output

MSW 4V rs and MSW 4SV rs • Introduction 1

Auto switching — when enabled, automatically selects the highest numbered input with

video sync present

Vertical interval switching — ensures glitch-free transitions

Compact size — 1U, quarter rack width metal enclosure

External power supply — the MSW 4V rs and MSW 4SV rs units are powered by a

12 VDC, 1.0 A power supply

Application Diagrams

CONTACT

MSW 4V rs

POWER

12V

.2A MAX

RS-232

Extron

MSW 4V rs

Composite

Video Switcher

Camera

VCR

Monitor

DVD

RS-232

100

LINK

ACT

COM

INPUT

RELAY

IPL 250

OFF

DISPLAY

MUTE

SCREEN

DOWN

VCR

DVD

DOC

CAM

LAPTOP

TCP/IP

TouchLink

™

Control

System

Figure 1. Typical Application for the MSW 4V rs

MSW 4SV rs

POWER

12V

.2A MAX

CONTACT

RS-232

Extron

MSW 4SV rs

S-video Switcher

S-VHS VCR

DVD

Projector

Monitor

RS-232

100

LINK

ACT

COM

INPUT

RELAY

IPL 250

OFF

DISPLAY

MUTE

SCREEN

DOWN

VCR

DVD

DOC

CAM

LAPTOP

TCP/IP

TouchLink

™

Control

System

Figure 2. Typical Application for the MSW 4SV rs

MSW 4V rs and MSW 4SV rs • Introduction 2

Installation

Overview

This section provides brief instructions for installing and operating either the MSW 4V rs or

the MSW 4SV rs switcher. Users are advised to follow the links to obtain more information,

elsewhere in this guide, about each step.

 Mount the switcher in a suitable location.

 Connect the composite and S-video (MSW 4SV rs only) inputs to video sources.

 Connect the composite and S-video (MSW 4SV rs only) outputs to video displays.

 Connect the power supply (provided).

CAUTION: Read the cautions on page 6 before connecting a power supply to

the switcher.

 Connect the RS-232 captive screw connector to a control device such as a

computer or IP Link controller (for use with an Extron TouchLink panel).

 Connect the Contact captive screw connector as required.

 Power on the switcher and all connected devices.

 Set up the auto switching mode and video mute. These can be initiated through

the front panel buttons, the Universal Switcher Control Program, or by SIS

commands.

 Select an input channel.

MSW 4V rs and MSW 4SV rs • Installation Overview 3

Panel Features

This section describes:

• Rear Panel Connections

• Front Panel Controls and Indicators

Rear Panel Connections

MSW 4SV rs

CONTACT

RS-232

Tx Rx

POWER

12V

.5A MAX

MSW 4V rs

CONTACT

RS-232

Tx Rx

POWER

12V

.5A MAX

MSW 4SV rs

MSW 4V rs

7 3

Figure 3. MSW 4SV rs and MSW 4V rs Rear Panel Connections

NOTE: The MSW switches during the vertical interval of input 1. For seamless

switching, ensure one of the genlocked devices is connected to input 1.

Composite video outputs (both switcher models) — For each composite video

output, connect a composite video display or other output device to this BNC

connector.

NOTES: • Outputs A and B output only one selected input signal.

• Both outputs can be used simultaneously.

• The MSW 4SV has a built-in encoder to convert S-Video to composite video

(output A).

MSW 4V rs and MSW 4SV rs • Panel Features 4

RS-232 connector — Connect a cable with a 3.5 mm, 5-pole captive screw connector

to this port for bidirectional RS-232 communication. Wire the connectors as shown

below.

NOTE: The Tx pin on the switcher connects to the Rx connector on the PC; the Rx

pin on the switcher connects to the Tx connector on the PC.

To Computer

Rear Panel RS-232 Port

Tx Rx

9-pin HD

Connector

Ground

Transmit

Receive

Green

Orange

Red

Transmit (Tx)

Receive (Rx)

Connect a ground wire between the switcher

and the computer or control system. If you

use cable that has a drain wire, tie the drain

wire to ground at both ends.

NOTE:

Figure 4. RS-232 Connector Wiring

This port has the following RS-232 protocol:

• 9600 baud

• 1 stop bit

• No parity

• 8 data bits

See “Command and Response Table for SIS Commands” on page 19

for the SIS commands used to communicate with the MSW switcher with

RS-232.

Contact connector — Connect a remote contact closure device to the MSW for

remote control of the switcher. You can also daisy chain the unit to other MSWs using

this 5-pole captive screw connector. This allows remote control of the other switchers.

NOTE: The switcher must be in normal (manual) mode for contact closure to

work (see “Mode Selection” on page 8).

To select an input using a contact closure device, such as an Extron CCR 204 Contact

Closure Remote Control or a locally constructed device, momentarily short the pin

for the desired input number to logic ground (pin 5). To force one of the inputs to be

always selected, leave the short in place. The short overrides any front panel input

selections.

You can also daisy chain multiple MSWs by using the contact connector. This allows

for front panel control of all switchers (for example, touch the input button on one

MSW to switch all MSWs). Wire pin 1 to pin 1, pin 2 to pin 2, and so on.

S-video output (MSW 4SV rs only) — Connect an S-video display or other device to

this 4-pin mini DIN connector for the S-video output.

S-video inputs 1 through 4 (MSW 4SV rs only) — For each input, connect an

S-video source to one of these 4-pin mini DIN connectors.

CONTACT

MSW 4V rs and MSW 4SV rs • Panel Features 5

Composite video inputs 1 through 4 (MSW 4V rs only) — For each input, connect

a composite video source to one of these BNC connectors.

Power connector — Plug the external 12 VDC power supply into this 2-pole, 3.5 mm

captive screw connector. The power supply is included with the unit.

If power is disconnected from the MSW, the unit retains mode and input settings.

CAUTIONS: • Always use a power supply supplied by or specied by Extron. Use of an

unauthorized power supply voids all regulatory compliance certiﬁcation

and may cause damage to the supply and the end product.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in

air handling spaces or in wall cavities. The power supply is to be located

within the same vicinity as the Extron A/V processing equipment in an

ordinary location, Pollution Degree 2, secured to the equipment rack

within the dedicated closet, podium or desk.

• The installation must always be in accordance with the applicable

provisions of National Electrical Code ANSI/NFPA 70, article 75 and the

Canadian Electrical Code part 1, section 16. The power supply shall not be

permanently ﬁxed to building structure or similar structure.

To wire the connector, do the following:

1. Cut the DC output cord to the length needed.

2. Strip the jacket to expose 3/16 inch (5 mm) of the conductors.

Power Supply

Output Cord

Captive Screw

Connector

SECTION A–A

Ridges

Smooth

Tie Wrap

Figure 5. Power Supply Connection

NOTES: • The power connector on the rear panel is orange; however, the plug for

the provided power cord may be either orange or blue. Either color plug

can be connected to the rear panel receptacle.

• The length of the exposed wires in the stripping process is critical. The

ideal length is 3/16 inches (5 mm). Any longer and the exposed wires

may touch, causing a short circuit between them. Any shorter and the

wires can be easily pulled out even if tightly fastened by the captive

screws.

• Do not tin the wires. Tinned wire does not hold its shape and can

become loose over time.

3. Slide the leads into the supplied captive screw plug and secure them using a small

screwdriver.

MSW 4V rs and MSW 4SV rs • Panel Features 6

4. Use the supplied tie-wrap to strap the power cord to the extended tail of the

connector.

5. Before connecting the power cord, verify the polarity by plugging it into the

power supply with no load and checking the output with a voltmeter.

WARNING The two power cord wires must be kept separate while the

power supply is plugged in. Remove power before wiring.

Alternately, an Extron PS 124 Universal 12 VDC power supply (part number

60-1022-01) can power up to eight MSWs or other Extron 12 VDC devices using

only one AC power connector.

Front Panel Controls and Indicators

The MSW 4V rs and MSW 4SV rs have identical front panels, shown in figure 6.

A/V SWITCHER

MODE NORMAL

AUTO

SWITCH

5 4 3

Figure 6. MSW 4V rs and MSW 4SV rs Front Panel

Input Selection

Input 1 through 4 LEDs — The Input LEDs light to identify the selected input.

Input 1 through 4 buttons — Each Input button selects the associated input for

output.

The Input 1 (e), Input 2 (d), and Input 3 (c) buttons are also used to toggle auto

switch mode on and off. See the following section.

Auto Switch Mode Controls and Indicators

When auto switch is activated, the switcher automatically detects and selects the highest

numbered input with video sync present.

Auto (switch) button — The Auto button is used with the Mode button (e) to

select auto switch mode. Auto is a secondary function of the Input 3 button.

Normal button — The Normal button is used with the Mode button (e) to select

normal mode. Normal is a secondary function of the Input 2 button.

Mode button — The Mode button is used with the Normal button (d) or Auto

button (

c) to select the switching mode. Mode is a secondary function of the Input 1

button. See “Mode selection” on the next page.

Auto Switch LED — When lit, the Auto Switch LED indicates that the switcher is

in auto switch mode. In this mode, the MSW automatically switches to the highest

numbered input with active sync pulses. When this LED is unlit, the switcher is in

normal (manual) mode.

MSW 4V rs and MSW 4SV rs • Panel Features 7

Mode Selection

The default method for changing channels is Normal mode (using front panel buttons). To

activate auto switch mode:

1. Press and hold the Mode (Input 1) and Auto (Input 3) buttons simultaneously.

2. Release the Mode and Auto buttons simultaneously. The Auto Switch LED turns on,

indicating that auto switch is enabled.

A/V SWITCHER

MODE NORMAL

AUTO

SWITCH

Figure 7. Turning on Auto Switch Mode

To turn auto switch mode off (Normal mode):

1. Press and hold the Mode (Input 1) and Normal (Input 2) buttons simultaneously.

2. Release the Mode and Normal buttons simultaneously. The Auto Switch LED is unlit

and the MSW switches to the previously selected input

A/V SWITCHER

MODE NORMAL

AUTO

SWITCH

Figure 8. Turning off Auto Switch Mode

Output (Video) Mute

Video mute suppresses video signals being sent to either output.

1. Press and hold the Mode (Input 1) and Input 4 buttons simultaneously.

2. Release both buttons simultaneously. The output (video) signal is muted.

To restore the video signal, press the same buttons:

1. Press and hold the Mode (Input 1) and Input 4 buttons simultaneously.

2. Release both buttons simultaneously. The output (video) signal is restored.

Vertical Interval Switching

The MSWs switch inputs during the vertical interval of the video signal that is on input 1.

In a genlocked system, switching to any input is glitch-free if one of the genlocked devices

is connected to input 1.

MSW 4V rs and MSW 4SV rs • Panel Features 8

Control Software

Universal Switcher Control Program

The Windows®-based Extron Universal Switcher Control Program provides an alternative to

configuring and operating the switcher through the front panel or SIS commands. The

program is compatible with Windows 2000 or later versions of the Windows operating

system.

Installing the Software

The control program can be downloaded from the Extron Website and is on the Extron

Software Products DVD. Install the software from the DVD as follows:

1. Insert the DVD into the drive. The installation program should start automatically. If it

does not self-start, run Launch.exe from the disc. The Extron software DVD window

appears.

Figure 9. Extron Software DVD Opening Screen

2. Click the Software icon.

3. Scroll to the Universal Switcher Control program and click the Install link at right.

Figure 10. Universal Switcher Install Link

By default, the Windows installation creates a C:\Program Files\Extron\UnivSW folder

and places a Universal Switcher icon onto the desktop.

Visit the Extron Web site (www.extron.com/download) if the disk is unavailable for

installation or to check if new software is available.

MSW 4V rs and MSW 4SV rs • Control Software 9

Using the Software

1. To run the software, double-click the Universal Switcher Control Program

icon on your PC desktop.

2. In the Communication Setup window (see ﬁgure 11), select the comm port

that is connected to the RS-232 port on the MSW. Click OK.

Figure 11. Communication Setup Window

3. The Universal Switcher Control Program window displays the selected input and

switching mode (Front Panel or Auto Switch).

Figure 12. Universal Switcher Output Window

MSW 4V rs and MSW 4SV rs • Control Software 10

4. Select and click the desired input button. Symbols for the state of each LED are shown

below:

Indicates that the input signal is not present and not selected

Indicates that the input signal is selected

Supresses the video image

When unlit (as shown), the switcher is in normal mode; when lit

(green), the switcher is in auto switch mode

5. Click on the Auto Switch tab in the top right corner to reveal

the Auto Switch status box. The Auto Switch radio buttons

indicate which mode is currently selected.

6. Click the Mute Video check box to suppress the video image.

Using the Help File

For information on how to use the Universal Switcher Control Program and explanations

of its features and functions, access the help program using any of the following methods:

• On your desktop Start menu, click Start > All Programs >

Extron Electronics > Universal Switcher > Universal Switcher Help.

• From within the switcher control program, select Help > Contents on the task bar.

• With the switcher control program open, press the <F1> key.

Updating the Firmware

Downloading the MSW 4V rs and 4SV rs Firmware

Extron periodically updates product firmware in conjunction with the release of new

software revisions. When updating any Extron software to the latest revision level, please

be sure to read the supplied release notes, or contact an Extron Application Engineer to

determine if your Extron product requires a firmware update (see the Extron Website for

contact information).

To find the latest MSW firmware, do the following:

1. Go to www.extron.com/download.

2. In the sidebar menu, click Firmware.

3. Find the MSW 4 rs series on the alphabetical list (you may need to click the “Next”

arrow).

4. Click the Download link for the product series and follow the instructions that appear

on the screen.

5. The ﬁle will be saved onto your computer. Note the folder where you saved the

ﬁrmware ﬁle.

CAUTION: Do not interrupt the ﬁrmware upload before it is 100% complete.

Interrupting the upload corrupts the ﬁrmware and the switcher will

not operate properly afterwards. If you experience problems with this

procedure, call the Extron S

Sales and Technical Support Hotline.

MSW 4V rs and MSW 4SV rs • Control Software 11

Downloading and Installing the Firmware Loader

Extron recommends using the Firmware Loader software to update the firmware on the

MSW 4V rs and MSW 4SV rs. If you do not already have the Firmware Loader software

installed on your computer, download it as follows:

1. Go to www.extron.com/download.

2. On the Download Center screen, click Software in the left sidebar menu.

3. On the next Download Center screen, locate and click the Download link for the

latest version of Firmware Loader.

Figure 13. Firmware Loader Download Link

4. On the next screen, enter the requested information, then click the

Download fw_loadernxnxn.exe button (where n is the Firmware Loader version

number).

5. Follow the instructions on the rest of the download screens to save the executable

Firmware Loader installer ﬁle to your computer. Note the folder to which you saved

the ﬁle.

6. In Windows Explorer or another le browser, locate the downloaded executable

installer ﬁle and double-click it to open it.

7. Follow the instructions on the Installation Wizard screens to install the Firmware

Loader to your computer. Unless you specify otherwise, the installer program places

the Firmware Loader ﬁle at C:\Program Files\Extron\FWLoader.

Using the Control Program to Update the Firmware

To upload the latest firmware to the MSW using the control program, do the following:

1. Open the Universal Switcher Control Program (see “Using the software,” on page

10).

2. From the Conﬁgure menu, choose Firmware Loader.

NOTE: Firmware Loader must be installed on the PC for this option to work.

Figure 14. Choosing Firmware Loader

MSW 4V rs and MSW 4SV rs • Control Software 12

3. The Add Device window appears. On the Add Device window, select the appropriate

device and connection method.

Figure 15. Add Device Window

4. From the remaining drop-down menus, select the appropriate port conﬁguration

parameters (obtained from your system administrator). The defaults are 9600 baud

rate, no parity, 8 data bits, and one stop bit.

5. Click on the Connect button. The name of the selected device should appear in

green text with a check mark next to it.

6. Click on the Browse button to locate the appropriate ﬁrmware ﬁle for the device.

Select the ﬁle and click on the Open button. The ﬁle extension must be .S19.

CAUTION: Using a le with an incorrect extension may cause the unit to stop

functioning.

Figure 16. Choose Firmware File Window

MSW 4V rs and MSW 4SV rs • Control Software 13

7. If you will be uploading rmware to multiple MSW switchers, do the following:

a. Click Add Next. Your rst device is added to the Devices eld in Firmware

Loader window, and the Add Device window remains open.

b. Enter the connection information for the device and click the Connect button.

c. Select the appropriate ﬁrmware for the device by using the Browse button.

d. Repeat steps 7a through 7c until all desired devices have been added to the

Firmware Loader window.

8. When nished adding devices, click Add. The Add Device window closes, leaving

the Firmware Loader window open with the added MSW devices highlighted and

selected.

9. If you want to remove a device from the Firmware Loader window, do the following:

a. Highlight the names of the devices to be deleted from the Firmware Loader

window.

b. Select Remove Selected Devices from the Edit menu.

To remove all devices from the Firmware Loader window, select Remove All

Devices from the Edit menu.

CAUTION: Before clicking on the Begin button, check to make sure the

appropriate rmware les is applied to the devices. Uploading a le

with an incorrect extension may cause the unit to stop functioning.

10. Click Begin to start the rmware uploading process. While the rmware is being

updated, a progress bar shows the status of the upload, while the Transfer Time ﬁeld

displays the time elapsed and the time remaining in the process. In addition, the

percent of the ﬁle that has been uploaded is displayed in the Total Progress ﬁeld until

the entire ﬁrmware ﬁle is uploaded.

Figure 17. Firmware Upload in Progress

11. When the rmware update is nished, “Completed” appears above the progress bar

in the Total Progress ﬁeld. The Total Progress ﬁeld displays “100%” and the status

displays “Completed”. Close the Firmware Loader window.

CAUTION: If the Firmware Loader utility exits before the status bar has

progressed completely across the indicator window, the ﬁrmware may

be corrupted and may no longer respond to the Universal Switcher

Control Program. If you experience problems with this procedure, call

the Extron S

Sales and Technical Support Hotline.

MSW 4V rs and MSW 4SV rs • Control Software 14

Page is loading ...

Extron MSW 4SV rs User manual

Brand: Extron

Model: MSW 4SV rs

Category: Video switches

Type: User manual

This manual is also suitable for

Download PDF

report

Extron MSW 4SV rs User manual

This manual is also suitable for

Extron MSW 4SV rs User manual

Related papers

Other documents