Western Omega Sky Installation and Operating Instructions

Brand: Western

Model: Omega Sky

Type: Installation and Operating Instructions

Omega Sky EN

13-05-2020

Installation, use and maintenance manual

2We reserve the right to make changes without any prior notice.Translation from original instructions

THANK YOU

Thank you for choosing our product.

It is the result of many years’ experience and careful design and has been built with rst-class quality materials and advan-

ced technologies.

Declaration or certicate of conformity also guarantees that the equipment meets the requirements of the European Machi-

nery Safety Directive.

The quality level is constantly monitored, and therefore our products are synonymous with Safety, Quality and Reliability.

Changes considered necessary for product improvement may be made to the stated data at any time without any obligation

to give prior notice.

Thank you again

Read this manual carefully before installing, testing or starting this unit.

Give this manual and all complementary documentation to the operator of the system who will be responsible

for keeping them so they are always available if needed.

The images and drawings contained herein are examples only.

3
We reserve the right to make changes without any prior notice. Translation from original instructions
Contents
Introduction  6
1  Conformity  6
2  Description  6
2.1 Symbols 6
2.2  Labels 7
Safety  8
1  General safety precautions  8
1.1 Discharge of the safety valves 9
1.2  Emergency stop 9
2  Basic rules  10
2.1 Water ow rate at the heat exchangers 11
2.2  Water composition 11
2.3  Minimum water content in the system 12
2.4 Installing the ow switch 13
2.5  Operation with water to the evaporator at low temperature 15
2.6  Operation with water to the condenser at low temperature 15
2.7 Condensation control at the source hydraulic circuit 16
2.8 Hydraulic connection to the heat recuperator (DC option) 18
2.9 Refrigerant leak detector 19
3  Noise  20
4  Residual risks  20
5  Safety information on the refrigerant uid  21
5.1 Hazards and health consequences 21
Receiving the product and storage  22
1  Reception  22
2  Transport  22
3  Handling  23
4  Storage  24
Ecodesign conformity  25
1  Documentation supplied with the product  25
1.1 Units conforming to all EC requirements including the Ecodesign Directive 25
1.2  Units exempt from the Ecodesign Directive and in general conforming to all EC requirements 25
1.3  Partly completed machine 26
1.4 Attached Documents envisaged with regard to the type of unit 26
1.5  Eciency parameters required for conformity 26
2  Conformity of the application  27
Product description  28
1  Intended use  28

4We reserve the right to make changes without any prior notice.Translation from original instructions
2  Unintended use  28
3  Control and safety devices  29
4  Principles of operation  29
5  Structure  29
6  Specications  29
7  Control panel  30
7.1 Switching the unit on/o 30
7.2  Changing from cooling to heating 30
7.3  Changing from heating to cooling 30
7.4 Change of set point in cooling operating mode 30
7.5  Change of set point in heating operating mode 31
8  Wiring diagram  31
Installation  32
1  Dimensions and weight  32
2  Place of installation  32
3  Installation  33
3.1 Positioning the units 33
3.2  Positioning the remote condenser 33
3.3  Anti-vibration mounts 33
3.4 Noise attenuation 34
3.5  Minimum distances 34
4  Hydraulic connections  35
4.0  User hydraulic circuit 36
4.1 Source hydraulic circuit 37
4.2  Recovery hydraulic circuit 38
4.3  Hydraulic circuit for heat pump units with reversal on the water 39
5  Hydraulic circuits for FC/NG units  40
5.1 Unit with only "FC/NG management" 40
5.2  Unit with "FC/NG kit" 42
6  Electrical connections  44
7  Connections for Multi Free management  46
8  Refrigeration connections  47
8.1 Making the piping with remote heat exchanger (LC versions) 47
8.2  Making the piping for the LC versions 48
8.3  LC version: unit installed at a lower level than the remote exchanger 49
8.4 LC version: unit installed at a higher level than the remote exchanger 49
9  Vacuum and refrigerant charge  50
10  Topping up with oil  51
Commissioning  52

5
We reserve the right to make changes without any prior notice. Translation from original instructions
1  Preliminary operations  52
1.1 Checking the pre-charge of the expansion vessel 53
1.2  Checking the volume of the expansion vessel 54
1.3  Preliminary operations for LC units 55
1.4 Preliminary operations for the source circuit 55
1.5  Preliminary operations for the FC/NG source circuit 55
2  First starting  56
2.1 Hydraulic tests 56
2.2  Functional tests 57
2.3  Unit with remote exchanger 57
3  Calibration of safety components  58
4  Checks during operation  59
4.1 Checks during operation for FC/NG units 60
5  Alarms and malfunctions  61
5.1 General troubleshooting 61
6  Temporary stop  63
7  Stop for long periods of time  63
Maintenance  64
1  Adjustments  64
2  Cleaning the remote exchanger  65
3  Internal cleaning  65
3.1 Cleaning the unit 65
4  Periodic checks  66
5  Unscheduled maintenance  67
5.1 Special work 67
Decommissioning  68

6We reserve the right to make changes without any prior notice.Translation from original instructions

1 INTRODUCTION

1.1 Conformity

With regard to relevant regulations and directives, see the declaration of conformity that is an integral part of the manual.

1.2 Description

1.2.1 Symbols

A description of the main symbols used in this manual and on the labels axed to the unit is given below.

Danger symbol; take extreme care.

Danger symbol; moving mechanical parts.

Danger symbol; live parts.

Warning symbol; important information

Note symbol; suggestions and advice

Danger sign: ammable gas.

We reserve the right to make changes without any prior notice. Translation from original instructions

1.2.2 Labels

For the constructional features, available models and technical data, please refer to the Technical Catalogue.

The model, serial number, features, power supply voltage and so on are shown on the labels axed to the unit (the following

illustrations are shown only as an example).

The Manufacturer adopts a continuous development policy and, in this perspective, reserves the right to

make changes and improvements to the documentation and to the units without prior notice.

The Technical Catalogue, the labels placed directly on the unit and the various diagrams referred to below,

must be considered an integral part of this manual.

Do not remove or alter the labels placed on the unit.

8We reserve the right to make changes without any prior notice.Translation from original instructions

2 SAFETY

2.1 General safety precautions

A space of about 2 metres around the unit is identied as external danger zone.

If the unit is positioned in an unprotected place that can be reached by unqualied persons, access to this area must be

prohibited by special guarding.

The equipment operator is responsible for complying with regulatory obligations.

The equipment operator is the person who has actual control over the technical operation and free access, which means

the possibility of monitoring its components and their operation and the possibility of granting access to third parties.

The equipment operator has the power (including nancial power) to decide on technical modications, checks and repairs.

The equipment operator may give instructions to employees or to external companies for carrying out maintenance and

repair operations.

Only an authorised operator should be able to access the unit.

Installation and maintenance or repair of the unit must be carried out by personnel and companies holding a certicate

issued by a certication body designated by a member state that certies the requirements contained in Commission Re-

gulation (EC) No. 517/2014.

The internal danger zone can be accessed by removing the protective devices and entering the unit.

On no account must unqualied personnel be allowed to enter the unit and no one should be allowed to enter before the

power to it has been turned o.

The user can interact with the unit only through the control and external OK signals.

Only authorised knowledgeable personnel may access the unit in compliance with safety in the workplace regulations.

Council Directive 89/391/EEC, of 12 June 1989, on the introduction of measures to encourage improvements in the health

and safety of workers at work.

Also, knowledge and understanding of the manual are indispensable for reducing risks and for improving the health and

safety of workers.

The operator who enters the unit must have sucient knowledge to perform the various activities throughout the technical

life of the machine.

The operator must know what to do when faced with possible anomalies, malfunctions or conditions of danger to himself or

others, and in any case, he must comply with the following instructions:

Stop the unit immediately by using the emergency device.

Do not do anything that goes beyond your duties and technical knowledge.

Inform the manager immediately and do not take personal initiatives.

Before carrying out any work on the unit, make sure you have turned o the power supply to it. Refer to the

section on maintenance work.

We reserve the right to make changes without any prior notice. Translation from original instructions

In units with capacitors and/or inverters, certain components can remain live for several minutes even after

having turned o the main switch.

Wait 10 minutes before working on the electrical parts of the unit.

Circuits supplied from external sources (made with orange cable) can remain live even after the power sup-

ply to the unit has been turned o.

Work on the unit only if there is sucient lighting for the type of work to be carried out.

Failure to comply with the instructions in this manual and any modications made to the unit without prior written consent,

will immediately void the warranty.

The law regulating the use of stratospheric ozone depleting substances prohibits the release of refrigerant

gases into the environment and obliges owners to recover and return them to the dealer or take them to spe-

cial collection centres at the end of their operational life.

The refrigerant contained in the refrigerant circuit is included among the substances subject to special con-

trol regulations provided for by law and must therefore be disposed of as indicated above.

Particular care should be taken during maintenance operations in order to reduce refrigerant leaks as much

as possible.

2.1.1 Discharge of the safety valves

If present on the refrigerant circuit, installation requirements and/or national regulations lay down that the discharge of the

safety valves must be routed to the outside.

The conveying must be done with a pipe whose diameter must be at least that of the valve outlet, and the weight of the pipe

must not be borne by the valve.

Always direct the discharge to areas where the jet cannot cause harm to anyone.

Risk of burns following contact with hot and cold parts.

2.1.2 Emergency stop

In case of emergency, an immediate stop is carried out using the red disconnecting switch/master switch on the electrical

control panel by turning it to 0. When it is turned to 0, the disconnecting switch turns o the power to the whole unit.

The main disconnect switch/master switch, used to electrically isolate the unit, is also intended for use as an

emergency device and it is only in an emergency that it should be used to stop the unit.

Unless there is an emergency condition, the operation of the unit must be stopped using the displayed con-

trols “control or external OK signal”.

10 We reserve the right to make changes without any prior notice.Translation from original instructions

2.2 Basic rules

All the units are designed and built in compliance with Directive 2014/68/EU of the European Parliament and of the Council

of 15 May 2014 on the approximation of the laws of the Member States relating to pressure equipment.

To ensure maximum safety, in order to prevent possible risks, follow the instructions below:

- this product contains pressurised vessels, live components, moving mechanical parts and very hot and cold surfaces

that, in certain situations, can pose a risk: all maintenance work must be carried out by skilled personnel equipped with

the necessary qualications in accordance with current regulations. Before carrying out any operation, make sure that

the personnel in charge has full knowledge of the documentation supplied with the unit.

- always have a copy of the documentation near the unit.

- The operations indicated in this manual must be integrated with the procedures indicated in the user instruction manuals

of the other systems and devices incorporated in the unit. The manuals contain all the necessary information for safely

managing the devices and the possible operating modes.

- use suitable protection (gloves, hard hat, protective glasses, safety shoes, etc.) for all maintenance or control opera-

tions carried out on the unit.

- Do not wear loose clothing, ties, chains, watches, etc., which can get caught in the moving parts of the unit.

- always use tools and protective equipment in excellent condition.

- The compressors and delivery gas pipes are at high temperature. Therefore, when working in the immediate vicinity, be

careful to avoid touching any components of the unit without suitable protection.

- do not work in the discharge trajectory of the safety valves.

- if the units are positioned in unprotected places which can easily be reached by unqualied persons, suitable protection

devices must be installed.

- the user must consult the installation and use system manuals, incorporated and attached to this manual.

- there may be potential risks that are not obvious. Warnings and signals are therefore displayed on the unit.

- Do not remove the warnings.

It is expressly forbidden to:

- remove or disable the safety guards;

- tamper with and/or modify, even partially, the safety devices installed on the unit.

If there are alarm warnings and consequent tripping of the safety devices, the user must call in skilled maintenance techni-

cians to x the problem immediately.

An accident can lead to serious injury or death.

The safety devices must be tested according to the guidelines in this manual.

The manufacturer does not assume any liability for damage/injury to persons, pets or objects arising from the re-use of

individual parts of the unit for functions or assembly situations dierent from the original ones. Tampering with/unauthorised

replacement of one or more parts of the unit is prohibited.

The use of accessories, tools or consumables other than those recommended by the Manufacturer relieves the latter from

civil and criminal liability.

Deactivation and scrapping of the unit must be carried out only by suitably trained and equipped personnel.

The units do not fall within the scope of Directive 2014/34/EU of the European Parliament and of the Coun-

cil, of 26 February 2014, on the approximation of the laws of the Member States relating to equipment and

protective systems intended for use in potentially explosive atmospheres.

We reserve the right to make changes without any prior notice. Translation from original instructions

2.2.1 Waterowrateattheheatexchangers

It is necessary to ensure that the water ow rate during operation is no higher than 1.5 times and no lower than 0.5 times

the nominal ow rate of the unit stated in the Technical Catalogue.

In any case, refer to the specic Technical Catalogue for the allowed conditions for water ow in and out of

the exchangers.

2.2.2 Water composition

Dissolved substances in the water can cause corrosion in the heat exchangers.

It is mandatory to make sure the parameters of the water comply with the following table:

Description Values

Total hardness 2,0 ÷ 6,0 °f

Langelier index - 0,4 ÷ 0,4

pH 7,5 ÷ 8,5

Electrical conductivity 10÷500 µS/cm

Organic elements -

Hydrogen carbonate (HCO3-) 70 ÷ 300 ppm

Sulphates (SO42-) < 50 ppm

Hydrogen carbonate / Sulphates (HCO3-/SO42-) > 1

Chlorides (Cl-) < 50 ppm

Nitrates (NO3-) < 50 ppm

Hydrogen sulphide (H2S) < 0,05 ppm

Ammonia (NH3) < 0,05 ppm

Sulphites (SO3), free chlorine (Cl2) < 1 ppm

Carbon dioxide (CO2) < 5 ppm

Metal cations < 0,2 ppm

Manganese ions (Mn++) < 0,2 ppm

Iron ions (Fe2+, Fe3+) < 0,2 ppm

Iron + Manganese < 0,4 ppm

Phosphates (PO43-) < 2 ppm

Oxygen < 0,1 ppm

ppm = mg/l

The use of water with values above the limits stated in the table will immediately void the warranty.

It is mandatory to include a system for eliminating possible organic substances in the water that could pass through the lter

and settle in the heat exchangers, which would lead to malfunctioning and/or breakage over time.

The use of water containing organic substances will immediately void the warranty.

12 We reserve the right to make changes without any prior notice.Translation from original instructions

2.2.3 Minimumwatercontentinthesystem

For correct operation of the unit, it is necessary to ensure a buering on the system such as to comply with the minimum

operating time considering the greater between the minimum OFF time and the minimum ON time.

In short, these contribute to limiting the number of times the compressors are switched on per hour and to preventing un-

desired deviations from the set point of the delivered water temperature.

The following experimental formula allows the minimum water volume of the system to be calculated:

where

v = Minimum water content of the system [ l ]

Ρtot = Total refrigeration capacity [kW]

N = N° of capacity reduction steps

Δτ = Time interval – the greater between minimum OFF time and minimum ON time [s]

ΔΤ = Allowed dierential on the water temperature [°C](unless specied, this is 2.5°C)

ρ = Water density 1000 [kg / ³]

Сp = Specic heat of water 4.186 [kJ / (kg°C)]

Fm = Q factor: experimental factor, dierent from 1 for some types of unit

K1 = Experimental multiplying constant depending on the type of compressor

With some terms grouped together, the formula can be rewritten as follows:

If the carrying uid consists of mixtures of water-glycol (ethylene or propylene), the density and specic heat values must

consequently be adjusted.

For units with screw compressor (both with stepped and continuous capacity reduction and with inverter) the constants

used in the formula assume the following values:

K [l/kW] 28,66

NFor units with 1 compressor = 4

For units with 2 compressors = 8

Fm 1

K1 0,8

The constant K considers that the maximum between the minimum ON and OFF time is Δτ=300s.

Larger amounts of water are in any case always preferable, because they allow a smaller number of stops and starts of

the compressors, less wear of them and an increase in the eciency of the system as a consequence of a reduction in the

number of transients.

We reserve the right to make changes without any prior notice. Translation from original instructions

2.2.4 Installingtheowswitch

Normally, a dierential pressure switch is installed between the inlet and outlet of the evaporator in the unit.

A ow switch, that must be connected by the installer, can be supplied as accessory.

The installed ow switch is provided with a 1” male connector.

The unit must be installed following the arrow that shows the direction of ow.

The installation must be done in a straight section of pipe away from lters, valves, etc. at a distance of at least 5 times the

pipe diameter, both upline and downline.

The ow switch is factory calibrated for installation on a horizontal pipe.

The push rod must be in the vertical position.

The connections of the ow switch with the terminal board in the electrical control panel must be made using the common

terminal and the terminal that is normally open when there is no water circulation.

Check the terminals provided for the ow switch in the wiring diagram of the unit.

Use a 2 x 1 mm² cable or at most a 2 x 1.5 mm² cable, with diameter between 6 and 9 mm, suitable for installation.

Lock the cable in place with cable ties in the section between the ow switch and the inlet to the electrical control panel.

Refer to the instructions provided with the ow switch to identify the correct set of foils.

Correct ow switch/sensor operation requires that the speed of the uid owing through them is within the

specied operating limits.

The table below shows the pipe diameters to be used in the system section where the ow switch is to be installed, accor-

ding to the ow rate.

Hydraulic diameter Min.owrate Max.owrate

(inches) m3/h m3/h

1" 2,5 3,6

1" 1/4 3,6 6,1

1" 1/2 6,1 9,2

2" 9,2 15,0

2" 1/2 15,0 24,0

3" 24,0 36,0

4" 36,0 60,0

5" 60,0 94,0

6" 94,0 120,0

8" 120,0 240,0

10" 240,0 381,6

The ow switch must be installed at the outlet on the exchanger that produces cold water and therefore, depending on the

unit, care must be taken to install it in the correct circuit.

The Manufacturer declines any and all responsibility for malfunctions due to non-complying installation of the

ow switch.

14 We reserve the right to make changes without any prior notice.Translation from original instructions

On all units, except for the “OH” versions, connect the ow switch to the outlet of the user-side exchanger,

indicated in the dimensional diagram and with the relevant plate on the unit.

On “OH” version units, connect the ow switch to the outlet of the source-side exchanger, indicated in the

dimensional diagram and with the relevant plate on the unit.

On “HPW” version units, connect a ow switch to the outlets of the user-side exchanger and to the outlets of

the source-side exchanger, indicated in the dimensional diagram and on the unit with the relevant plates.

We reserve the right to make changes without any prior notice. Translation from original instructions

2.2.5 Operationwithwatertotheevaporatoratlowtemperature

With temperatures below 5°C, it is mandatory to work with water and anti-freeze mixtures, and also change the safety devi-

ces (anti-freeze, etc.), which must be carried out by qualied authorised personnel or by the manufacturer.

The glycol percentage by weight is determined based on the desired temperature of the chilled water (see table).

Minimum ambient temperature or liquid

outlet temperature (°C) 0 -5 -10 -15 -20 -25 -30 -35 -40

Freezing point (°C) -5 -10 -15 -20 -25 -30 -35 -40 -45

Antifreeze % by weight

Ethylene glycol 6 22 30 36 41 46 50 53 56

Propylene glycol 15 25 33 39 44 48 51 54 57

If ambient temperatures are expected to be lower than the freezing point of water, it is essential to use an-

ti-freeze mixtures in the above-mentioned percentages.

In the case of units with pump units applied in systems with glycol percentages above 30%, when ordering,

a request must be made for a technical check for compatibility of the pumps and, if necessary, the best so-

lution identied, which could require the use of a specic hydraulic module or the application of pumps with

special electric motors.

2.2.6 Operationwithwatertothecondenseratlowtemperature

The standard units are not designed to operate with water to the condenser at too low a temperature (refer to the Technical

Catalogue for the limits).

In order to operate below this limit, the unit could require structural modications.

If required, please contact our company.

16 We reserve the right to make changes without any prior notice.Translation from original instructions

2.2.7 Condensation control at the source hydraulic circuit

The temperature and ow rate of the source circuit water must be maintained within the operating limits stated in the Tech-

nical Catalogue.

It is essential for the water to come in at the connection indicated in the dimensional diagram and with the

relevant plate on the unit.

A modulating three-way valve that will ensure an incoming water temperature within the operating limits

stated in the Technical Catalogue must be installed for correct operation of the unit.

Fig. 1 3-way valve installation layout

02 Condenser

EL Motor-driven pump

V3 Thermostatic three-way valve

The three-way modulating valve can be supplied as accessory by the manufacturer.

As accessory, the signal to control it can also be supplied with the modulating valve.

The hydraulic connection of the three-way modulating valve must be made as shown in the illustration.

Fig. 2 Hydraulic connection of three-way valve

02 Condenser

EL Motor-driven pump

V3 Three-way valve

We reserve the right to make changes without any prior notice. Translation from original instructions

As accessory, a two-way modulating valve can be supplied by the manufacturer as an alternative to the three-way valve.

The hydraulic connection of the two-way modulating valve must be made as shown in the illustration.

Fig. 3 Hydraulic connection of two-way valve

02 Condenser

V2 Two-way valve

For some sizes, the manufacturer supplies a three-way modulating valve, with way "B" closed or to be clo-

sed with a blind ange, to be used as two-way valve.

If the signal for controlling the valve is used, connect the servo control as shown in the wiring diagram.

As an alternative to the modulating valve, it is possible to use a pressure switch valve for each refrigerant circuit that will

ensure an average condensing temperature of at least 40°C.

Fig. 4 Pressure switch valve installation layout

02 Condenser

40 Pressure switch valve

Also consult the hydraulic diagram of the unit for correct installation of the condensation control device in the

source hydraulic circuit.

18 We reserve the right to make changes without any prior notice.Translation from original instructions

2.2.8 Hydraulic connection to the heat recuperator (DC option)

The heat recuperator must be connected to a closed hydraulic circuit.

Constant renewal of water causes limescale to build up in the exchanger, which reduces its eciency in a

short time and makes it unserviceable.

All units equipped with heat recuperator have water temperature control probe on the return from the system.

The microprocessor controller enables the heat recovery unit when necessary, by disabling the condenser, and restores its

operation when the heat recovery unit water temperature has reached the required value.

If an anomaly occurs on the hydraulic heat recovery circuit, the controller will restart the condenser.

It is essential for the water to come in at the connection indicated in the dimensional diagram and with the

relevant label on the unit.

A modulating three-way valve that will ensure an incoming water temperature within the operating limits

stated in the Technical Catalogue must be installed for correct operation of the unit.

Fig. 5 3-way valve installation layout

02 Heat recuperator

EL Motor-driven pump

V3 Thermostatic three-way valve

As an alternative to the 3-way modulating valve, it is possible to use a pressure switch valve for each refrigerant circuit that

will ensure an average condensing temperature of at least 40°C.

Fig. 6 Pressure switch valve installation layout

02 Heat recuperator

40 Pressure switch valve

We reserve the right to make changes without any prior notice. Translation from original instructions

2.2.9 Refrigerant leak detector

A refrigerant leak detector with semiconductor sensor can be installed on the units.

This device allows immediate detection of refrigerant leaks, with a warning or with stopping of the unit in pump down, de-

pending on how it is managed.

The installation of the device is in line with European F-GAS regulations and USA ASHRAE regulations.

By default, the device is set at 100 ppm with a one minute delay.

Local regulations may require dierent calibration values with specic sensor checking and calibration procedures.

The main regulations require a check with tests at least once a year.

Check your local regulations on calibration and the testing requirements.

The alarm contact opens for 5 seconds any time power is cut out and then restored to the sensor. Set a

suitable delay in the warning message. Up to 3 minutes are required for the sensor to complete the start-up

cycle.

The detector must be tested and/or calibrated by a qualied technician.

To test and calibrate the device, qualied operators must know the rules and regulations laid down by the industrial sector

and/or by the country of installation.

In the event of a signicant refrigerant leak with prolonged exposure, check the sensor and, if necessary,

replace the sensing element.

In any case, the sensing element of the device has a lifetime after which it must be replaced.

As regards the device testing and calibration method and procedures, refer to the “+0300035EN” manual available on the

site www.Carel.com in the “Services” section of the “Documentation” folder.

For replacement of the sensing device and for other accessories needed for calibration, refer to your custo-

mer service centre.

20 We reserve the right to make changes without any prior notice.Translation from original instructions

2.3 Noise

The starting of the unit, with activation of its components, emits a noise whose intensity varies depending on the operating

level.

The correct location choice and the correct installation prevent the unit causing annoying noise due to resonances, reections

and vibrations.

2.4 Residual risks

The unit uses technical means suitable for protecting people, animals and things against hazards that cannot reasonably

be eliminated or suciently reduced through design.

The presence of an operator is not required for normal operation of the unit. The change from the "OFF" state to the "ON"

state, and vice versa, of the unit can be carried out remotely or through the display, without having to enter areas at risk.

Access restriction is part of correct installation to eliminate residual risks during normal operation.

Removal of the restrictions gives access to cold parts, hot parts and sharp edges.

When the electrical boxes and the electrical control panel are open, live parts can be accessed.

Do not:

- remove or disable the safety guards;

- tamper with and/or modify, even partially, the safety devices installed on the unit.

Page is loading ...

Western Omega Sky Installation and Operating Instructions

Western Omega Sky Installation and Operating Instructions

Western Omega Sky Installation and Operating Instructions

Related papers

Other documents