Vega VEGAPULS 69 Operating instructions

Operating Instructions

Radar sensor for continuous level

measurement of bulk solids

VEGAPULS 69

Two-wire 4 … 20 mA/HART

Document ID: 47247

2

Contents

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

Contents

1 About this document ............................................................................................................... 4

1.1 Function ........................................................................................................................... 4

1.2 Target group ..................................................................................................................... 4

1.3 Symbols used................................................................................................................... 4

2 For your safety ......................................................................................................................... 5

2.1 Authorised personnel ....................................................................................................... 5

2.2 Appropriate use ................................................................................................................ 5

2.3 Warning about incorrect use ............................................................................................. 5

2.4 General safety instructions ............................................................................................... 5

2.5 EU conformity ................................................................................................................... 6

2.6 NAMUR recommendations .............................................................................................. 6

2.7 Radio license for Europe .................................................................................................. 6

2.8 Radio license for USA ...................................................................................................... 7

2.9 Radio license for Canada ................................................................................................. 7

2.10 Installation and operation in the USA and Canada ........................................................... 9

2.11 Environmental instructions ............................................................................................... 9

3 Product description ............................................................................................................... 11

3.1 Conguration .................................................................................................................. 11

3.2 Principle of operation...................................................................................................... 12

3.3 Packaging, transport and storage ................................................................................... 13

3.4 Accessories.................................................................................................................... 14

4 Mounting ................................................................................................................................. 15

4.1 General instructions ....................................................................................................... 15

4.2 Mounting versions, plastic horn antenna ........................................................................ 15

4.3 Mounting preparations, mounting strap .......................................................................... 18

4.4 Mounting instructions ..................................................................................................... 19

5 Connecting to power supply ................................................................................................. 30

5.1 Preparing the connection ............................................................................................... 30

5.2 Connecting ..................................................................................................................... 31

5.3 Wiring plan, single chamber housing.............................................................................. 32

5.4 Wiring plan, double chamber housing ............................................................................ 33

5.5 Ex-d double chamber housing........................................................................................ 35

5.6 Double chamber housing with VEGADIS-Adapter .......................................................... 36

5.7 Wiring plan - version IP66/IP68, 1 bar ............................................................................ 37

5.8 Switch-on phase............................................................................................................. 37

6 Set up with the display and adjustment module ................................................................ 38

6.1 Insert display and adjustment module ............................................................................ 38

6.2 Adjustment system ......................................................................................................... 39

6.3 Measured value indication - Selection of national language ........................................... 40

6.4 Parameter adjustment - Quick setup .............................................................................. 41

6.5 Parameter adjustment - Extended adjustment................................................................ 41

6.6 Saving the parameterisation data ................................................................................... 55

7 Setup with PACTware ............................................................................................................. 56

7.1 Connect the PC .............................................................................................................. 56

7.2 Parameter adjustment with PACTware ............................................................................ 56

7.3 Saving the parameterisation data ................................................................................... 58

3

Contents

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

8 Set up with other systems .................................................................................................... 59

8.1 DD adjustment programs ............................................................................................... 59

8.2 Field Communicator 375, 475 ........................................................................................ 59

9 Diagnosis, asset management and service ........................................................................ 60

9.1 Maintenance .................................................................................................................. 60

9.2 Measured value and event memory ............................................................................... 60

9.3 Asset Management function ........................................................................................... 61

9.4 Rectify faults ................................................................................................................... 64

9.5 Exchanging the electronics module ................................................................................ 67

9.6 Software update ............................................................................................................. 67

9.7 How to proceed if a repair is necessary .......................................................................... 68

10 Dismount................................................................................................................................. 69

10.1 Dismounting steps.......................................................................................................... 69

10.2 Disposal ......................................................................................................................... 69

11 Supplement ............................................................................................................................ 70

11.1 Technical data ................................................................................................................ 70

11.2 Radio astronomy stations ............................................................................................... 81

11.3 Dimensions .................................................................................................................... 82

11.4 Industrial property rights ................................................................................................. 95

11.5 Trademark ...................................................................................................................... 95

Safety instructions for Ex areas

TakenoteoftheExspecicsafetyinstructionsforExapplications.

These instructions are attached as documents to each instrument

with Ex approval and are part of the operating instructions.

Editing status: 2020-04-21

4

1 About this document

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

1 About this document

1.1 Function

This instruction provides all the information you need for mounting,

connection and setup as well as important instructions for mainte-

nance,faultrectication,theexchangeofpartsandthesafetyofthe

user. Please read this information before putting the instrument into

operation and keep this manual accessible in the immediate vicinity

of the device.

1.2 Target group

This operating instructions manual is directed to trained personnel.

Thecontentsofthismanualmustbemadeavailabletothequalied

personnel and implemented.

1.3 Symbols used

Document ID

This symbol on the front page of this instruction refers to the Docu-

ment ID. By entering the Document ID on www.vega.com you will

reach the document download.

Information, note, tip: This symbol indicates helpful additional infor-

mation and tips for successful work.

Note: This symbol indicates notes to prevent failures, malfunctions,

damage to devices or plants.

Caution: Non-observance of the information marked with this symbol

may result in personal injury.

Warning: Non-observance of the information marked with this symbol

may result in serious or fatal personal injury.

Danger: Non-observance of the information marked with this symbol

results in serious or fatal personal injury.

Ex applications

This symbol indicates special instructions for Ex applications.

•

List

The dot set in front indicates a list with no implied sequence.

1 Sequence of actions

Numbers set in front indicate successive steps in a procedure.

Battery disposal

This symbol indicates special information about the disposal of bat-

teries and accumulators.

5

2 For your safety

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

2 For your safety

2.1 Authorised personnel

All operations described in this documentation must be carried out

onlybytrained,qualiedpersonnelauthorisedbytheplantoperator.

During work on and with the device, the required personal protective

equipment must always be worn.

2.2 Appropriate use

VEGAPULS 69 is a sensor for continuous level measurement.

Youcannddetailedinformationabouttheareaofapplicationin

chapter "Product description".

Operational reliability is ensured only if the instrument is properly

usedaccordingtothespecicationsintheoperatinginstructions

manual as well as possible supplementary instructions.

2.3 Warning about incorrect use

Inappropriate or incorrect use of this product can give rise to applica-

tion-specichazards,e.g.vesseloverllthroughincorrectmounting

or adjustment. Damage to property and persons or environmental

contamination can result. Also, the protective characteristics of the

instrument can be impaired.

2.4 General safety instructions

This is a state-of-the-art instrument complying with all prevailing

regulations and directives. The instrument must only be operated in a

technicallyawlessandreliablecondition.Theoperatorisresponsi-

ble for the trouble-free operation of the instrument. When measuring

aggressive or corrosive media that can cause a dangerous situation

if the instrument malfunctions, the operator has to implement suitable

measures to make sure the instrument is functioning properly.

The safety instructions in this operating instructions manual, the na-

tional installation standards as well as the valid safety regulations and

accident prevention rules must be observed by the user.

For safety and warranty reasons, any invasive work on the device

beyond that described in the operating instructions manual may be

carried out only by personnel authorised by the manufacturer. Arbi-

traryconversionsormodicationsareexplicitlyforbidden.Forsafety

reasons,onlytheaccessoryspeciedbythemanufacturermustbe

used.

To avoid any danger, the safety approval markings and safety tips on

the device must also be observed.

The low transmitting power of the radar sensor is far below the inter-

nationally approved limits. No health impairments are to be expected

with intended use. The band range of the transmission frequency can

be found in chapter "Technical data".

6

2 For your safety

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

2.5 EU conformity

ThedevicefullsthelegalrequirementsoftheapplicableEUdirec-

tives.ByaxingtheCEmarking,weconrmtheconformityofthe

instrument with these directives.

The EU conformity declaration can be found on our homepage.

2.6 NAMUR recommendations

NAMUR is the automation technology user association in the process

industry in Germany. The published NAMUR recommendations are

acceptedasthestandardineldinstrumentation.

ThedevicefullstherequirementsofthefollowingNAMURrecom-

mendations:

•

NE 43 – Signal level for fault information from measuring transduc-

ers

•

NE53–Compatibilityofelddevicesanddisplay/adjustment

components

•

NE107–Self-monitoringanddiagnosisofelddevices

For further information see www.namur.de.

2.7 Radio license for Europe

The instrument was tested according to the latest issue of the follow-

ingharmonizedstandards:

•

EN 302372 - Tank Level Probing Radar

•

EN 302729 - Level Probing Radar

It is hence approved for use inside and outside closed vessels in

countries of the EU.

Use is also approved in EFTA countries, provided the respective

standards have been implemented.

For operation inside of closed vessels, points a to f in annex E of

EN302372mustbefullled.

For operation outside of closed vessels, the following conditions must

befullled:

•

The instrument must be stationary mounted and the antenna

directed vertically downward

•

The instrument may only be used outside closed vessels in the

version with G1½ or 1½ NPT thread with integrated horn antenna.

•

The mounting location must be at least 4 km away from radio

astronomy stations, unless special permission was granted by the

responsible national approval authority

•

When installed within 4 to 40 km of a radio astronomy station,

the instrument must not be mounted higher than 15 m above the

ground.

A list of the respective radio astronomy stations can be found in chap-

ter "Appendix" of the operating instructions.

7

2 For your safety

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

2.8 Radio license for USA

This approval is only valid for USA. Hence the following text is only

available in the English language:

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

•

This device may not cause interference, and

•

This device must accept any interference, including interference

that may cause undesired operation of the device

This device is approved for unrestricted use only inside closed,

stationary vessels made of metal or concrete. From electronics index

.-03theuseincontainersmadeofreinforcedberglassisalsopermit-

ted.

For operation outside of closed vessels, the following conditions must

befullled:

•

This device shall be installed and maintained to ensure a verti-

cally downward orientation of the transmit antenna's main beam.

Furthermore, the use of any mechanism that does not allow the

main beam of the transmitter to be mounted vertically downward is

prohibited.

•

Operation of the instrument is only permitted with thread G1½ or

1½ NPT with integrated horn antenna.

•

Thisdeviceshallbeinstalledonlyatxedlocations.TheLPR

device shall not operate while being moved or while inside a mov-

ing container.

•

Hand-held applications are prohibited.

•

Marketing to residential consumers is prohibited.

Changesormodicationsnotexpresslyapprovedbythemanufac-

turer could void the user’s authority to operate this equipment.

2.9 Radio license for Canada

This approval is only valid for Canada. Hence the following texts are

only available in the English/French language:

This device complies with Industry Canada's license-exempt RSS

standard(s). Operation is subject to the following conditions:

•

This device may not cause interference, and

•

This device must accept any interference, including interference

that may cause undesired operation of the device

This device has been approved for both closed containers and open-

air environments with the following limitations:

•

ClosedContainers:Forinstallationsutilizingatiltduringinstalla-

tion: This device is limited to installation in a completely enclosed

container made of metal or concrete to prevent RF emissions,

which can otherwise interfere with aeronautical navigation, the

maximum approved tilt angel is 10°. From electronics index .-03

theuseincontainersmadeofreinforcedberglassisalsopermit-

ted.

8

2 For your safety

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

•

Open Air Environment: For operation outside of closed vessels,

thefollowingconditionmustbefullled:Thisdeviceshallbe

installed and maintained to ensure a vertically downward orienta-

tion of the transmit antenna's main beam. Furthermore, the use of

any mechanism that does not allow the main beam of the transmit-

ter to be mounted vertically downward is prohibited.

•

Operation of the instrument outside of closed vessels is only per-

mitted with G1½ or 1½ NPT with integrated horn antenna.

•

The installation of the LPR/TLPR device shall be done by trained

installers, in strict compliance with the manufacturer's instructions.

•

Thisdeviceshallbeinstalledonlyatxedlocations.TheLPR

device shall not operate while being moved or while inside a mov-

ing container.

•

Hand-held applications are prohibited.

•

Marketing to residential consumers is prohibited.

•

The use of this device is on a "no-interference, no-protection"

basis. That is, the user shall accept operations of high-powered

radar in the same frequency band which may interfere with or

damage this device.

•

However, devices found to interfere with primary licensing opera-

tions will be required to be removed at the user's expense.

•

The installer/user of this device shall ensure that it is at least 10 km

from the Dominion Astrophysical Radio Observatory (DRAO) near

Penticton, British Columbia. The coordinates of the DRAO are

latitude49°19′15″Nandlongitude119°37′12″W.Fordevicesnot

meeting this 10 km separation (e.g., those in the Okanagan Valley,

British Columbia,) the installer/user must coordinate with, and

obtain the written concurrence of, the Director of the DRAO before

the equipment can be installed or operated. The Director of the

DRAO may be contacted at 250-497-2300 (tel.)or 250-497-2355

(fax). (Alternatively, the Manager, Regulatory Standards, Industry

Canada, may be contacted.)

Le présent appareil est conforme aux CNR d’Industrie Canada ap-

plicables aux appareils radio exempts de licence. L’exploitation est

autorisée aux conditions suivantes :

•

L’appareil ne doit pas produire de brouillage; et

•

L’utilisateur de l’appareil doit accepter tout brouillage radioélect-

rique subi, même si le brouillage est susceptible d’en compromet-

tre le fonctionnement.

Cet appareil est homologué pour une utilisation dans les cuves fer-

mées et les environnements ouverts avec les restrictions suivantes :

•

Cuves fermées : Pour les installations impliquant une inclinaison

lors de l'installation : cet appareil ne doit être installé que dans

une cuve totalement fermée en métal ou en béton, pour empêcher

les émissions RF susceptibles d'interférer avec la navigation

aéronautique. L'angle d'inclinaison maximum autorisé est de 10°.

De l'indice électronique .-03, l'utilisation dans des conteneurs

fabriquésenbredeverreestégalementpermise.

•

Environnement ouvert : Pour l'utilisation hors des cuves fermées,

la condition suivante doit être remplie : L'appareil doit être installé

9

2 For your safety

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

et entretenu de manière à garantir une orientation verticale vers

le bas du faisceau principal de l’antenne émettrice. De plus,

l’utilisation de tout mécanisme ne permettant pas l’orientation ver-

ticale vers le bas du faisceau principal de l’émetteur est interdite

•

Il est uniquement autorisé d'utiliser la version d'appareil avec le

letageG1½ou1½NPTenenvironnementsouvertes.

•

L’installationd’undispositifLPRouTLPRdoitêtreeectuée

pardesinstallateursqualiés,enpleineconformitéavecles

instructions du fabricant.

•

Cetappareilnedoitêtreinstalléqu'àdesemplacementsxes.

L’appareil LPR ne doit pas être utilisé pendant qu’il est en train

d’être déplacé ou se trouve dans un conteneur en mouvement.

•

Les applications portables sont interdites.

•

La vente à des particuliers est interdite.

•

Ce dispositif ne peut être exploité qu'en régime de non-brouillage

et de non-protection, c'est-à-dire que l'utilisateur doit accepter que

des radars de haute puissance de la même bande de fréquences

puissent brouiller ce dispositif ou même l'endommager.

•

D'autre part, les capteurs de niveau qui perturbent une exploita-

tion autorisée par licence de fonctionnement principal doivent être

enlevés aux frais de leur utilisateur.

•

La personne qui installe/utilise ce capteur de niveau doit s'assurer

qu'il se trouve à au moins 10 km de l'Observatoire fédéral de

radioastrophysique (OFR) de Penticton en Colombie-Britannique.

Lescoordonnéesdel'OFRsont:latitudeN49°19′15″,longitude

O119°37′12″.Lapersonnequiinstalle/utiliseundispositifne

pouvant respecter cette distance de 10 km (p. ex. dans la vallée

de l'Okanagan [Colombie-Britannique]) doit se concerter avec le

directeurdel'OFRand’obtenirdesapartuneautorisationécrite

avant que l'équipement ne puisse être installé ou mis en marche.

Le directeur de l'OFR peut être contacté au 250-497-2300 (tél.) ou

au 250-497-2355 (fax). (Le Directeur des Normes réglementaires

d'Industrie Canada peut également être contacté).

2.10 Installation and operation in the USA and

Canada

This information is only valid for USA and Canada. Hence the follow-

ing text is only available in the English language.

Installations in the US shall comply with the relevant requirements of

the National Electrical Code (ANSI/NFPA 70).

Installations in Canada shall comply with the relevant requirements of

the Canadian Electrical Code

A Class 2 power supply unit has to be used for the installation in the

USA and Canada.

2.11 Environmental instructions

Protection of the environment is one of our most important duties.

That is why we have introduced an environment management system

with the goal of continuously improving company environmental pro-

10

2 For your safety

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

tection.Theenvironmentmanagementsystemiscertiedaccording

to DIN EN ISO 14001.

Pleasehelpusfullthisobligationbyobservingtheenvironmental

instructions in this manual:

•

Chapter "Packaging, transport and storage"

•

Chapter "Disposal"

11

3 Product description

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

3 Product description

3.1 Conguration

The scope of delivery encompasses:

•

VEGAPULS 69 radar sensor

•

Hexagon socket wrench (for instruments with swivel holder)

The further scope of delivery encompasses:

•

Documentation

– Quick setup guide VEGAPULS 69

– Instructions for optional instrument features

– Ex-specic"Safety instructions" (with Ex versions)

– Ifnecessary,furthercerticates

Information:

Optional instrument features are also described in this operating

instructions manual. The respective scope of delivery results from the

orderspecication.

This operating instructions manual applies to the following instrument

versions:

•

Hardware version from 1.0.3

•

Software version from 1.3.2

Thetypelabelcontainsthemostimportantdataforidenticationand

use of the instrument:

Scope of delivery

Scope of this operating

instructions

Type label

12

3 Product description

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

7

6

5

4

3

2

1

Fig. 1: Layout of the type label (example)

1 Instrument type

2 Product code

3 Approvals

4 Voltage supply and signal output, electronics

5 Protection rating

6 Measuring range (measurement accuracy optional)

7 Process and ambient temperature, process pressure

8 Material wetted parts

9 Hardware and software version

10 Order number

11 Serial number of the instrument

12 Data matrix code for VEGA Tools app

13 Symbol of the device protection class

14 ID numbers, instrument documentation

15 Reminder to observe the instrument documentation

16 NotiedauthorityforCEmarking

17 Approval directive

The type label contains the serial number of the instrument. With it

youcanndthefollowinginstrumentdataonourhomepage:

•

Product code (HTML)

•

Delivery date (HTML)

•

Order-specicinstrumentfeatures(HTML)

•

Operating instructions and quick setup guide at the time of ship-

ment (PDF)

•

Order-specicsensordataforanelectronicsexchange(XML)

•

Testcerticate(PDF)-optional

Move to "www.vega.com"andenterinthesearcheldtheserial

number of your instrument.

Alternatively, you can access the data via your smartphone:

•

Download the VEGA Tools app from the "Apple App Store" or the

"Google Play Store"

•

Scan the DataMatrix code on the type label of the instrument or

•

Enter the serial number manually in the app

3.2 Principle of operation

The VEGAPULS 69 is a radar sensor for continuous level measure-

mentofbulksolidsunderdierentprocessconditions.

Serial number - Instru-

ment search

Application area

13

3 Product description

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

It is ideal for level measurement in very high silos, large bunkers and

segmented vessels. The very good signal focussing ensures a simple

setup and reliable measurement.

TheVEGAPULS69isavailablewithdierentantennasystems:

1 2 3

Fig. 2: Antenna systems VEGAPULS 69

1 Metal-jacketed lens antenna

2 Plastic horn antenna

3 Thread with integrated horn antenna

The instrument emits a continuous, frequency-modulated radar signal

throughitsantenna.Theemittedsignalisreectedbythemedium

andreceivedbytheantennaasanechowithmodiedfrequency.The

frequency change is proportional to the distance and is converted into

the level.

3.3 Packaging, transport and storage

Your instrument was protected by packaging during transport. Its

capacity to handle normal loads during transport is assured by a test

based on ISO 4180.

The packaging consists of environment-friendly, recyclable card-

board. For special versions, PE foam or PE foil is also used. Dispose

of the packaging material via specialised recycling companies.

Transport must be carried out in due consideration of the notes on the

transport packaging. Nonobservance of these instructions can cause

damage to the device.

The delivery must be checked for completeness and possible transit

damage immediately at receipt. Ascertained transit damage or con-

cealed defects must be appropriately dealt with.

Up to the time of installation, the packages must be left closed and

stored according to the orientation and storage markings on the

outside.

Unless otherwise indicated, the packages must be stored only under

the following conditions:

•

Not in the open

•

Dry and dust free

Functional principle

Packaging

Transport

Transport inspection

Storage

14

3 Product description

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

•

Not exposed to corrosive media

•

Protected against solar radiation

•

Avoiding mechanical shock and vibration

•

Storage and transport temperature see chapter "Supplement -

Technical data - Ambient conditions"

•

Relative humidity 20 … 85 %

With instrument weights of more than 18 kg (39.68 lbs) suitable and

approved equipment must be used for lifting and carrying.

3.4 Accessories

The instructions for the listed accessories can be found in the down-

load area on our homepage.

The display and adjustment module is used for measured value indi-

cation, adjustment and diagnosis.

The integrated Bluetooth module (optional) enables wireless adjust-

ment via standard adjustment devices.

The interface adapter VEGACONNECT enables the connection of

communication-capable instruments to the USB interface of a PC.

The VEGADIS 81 is an external display and adjustment unit for VEGA

plics

®

sensors.

The VEGADIS adapter is an accessory part for sensors with double

chamber housings. It enables the connection of VEGADIS 81 to the

sensor housing via an M12 x 1 plug.

VEGADIS 82 is suitable for measured value indication and adjustment

of sensors with HART protocol. It is looped into the 4 … 20 mA/HART

signal cable.

The PLICSMOBILE T81 is an external GSM/GPRS/UMTS radio unit

for transmission of measured values and for remote parameter adjust-

ment of HART sensors.

PLICSMOBILE 81 is an internal GSM/GPRS/UMTS radio unit for

HART sensors for transmitting measured values and for remote

parameterization.

The overvoltage arrester B81-35 is used instead of the terminals in

the single or double chamber housing.

The protective cover protects the sensor housing against soiling and

intense heat from solar radiation.

Screwedangesareavailableindierentversionsaccordingtothe

following standards: DIN 2501, EN 1092-1, BS 10, ASME B 16.5,

JIS B 2210-1984, GOST 12821-80.

Storage and transport

temperature

Lifting and carrying

PLICSCOM

VEGACONNECT

VEGADIS 81

VEGADIS adapter

VEGADIS 82

PLICSMOBILE T81

PLICSMOBILE 81

Overvoltage protection

Protective cover

Flanges

15

4 Mounting

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

4 Mounting

4.1 General instructions

Protect your instrument against moisture ingress through the following

measures:

•

Use a suitable connection cable (see chapter "Connectingto

power supply")

•

Tighten the cable gland or plug connector

•

Lead the connection cable downward in front of the cable entry or

plug connector

This applies mainly to outdoor installations, in areas where high

humidity is expected (e.g. through cleaning processes) and on cooled

or heated vessels.

Note:

Makesurethatthedegreeofcontaminationspeciedinchapter

"Technical data" meets the existing ambient conditions.

Note:

Make sure that during installation or maintenance no moisture or dirt

can get inside the instrument.

To maintain the housing protection, make sure that the housing lid is

closed during operation and locked, if necessary.

Note:

For safety reasons, the instrument must only be operated within the

permissibleprocessconditions.Youcannddetailedinformationon

the process conditions in chapter "Technical data" of the operating

instructions or on the type label.

Hence make sure before mounting that all parts of the instrument ex-

posed to the process are suitable for the existing process conditions.

These are mainly:

•

Active measuring component

•

Processtting

•

Process seal

Process conditions in particular are:

•

Process pressure

•

Process temperature

•

Chemical properties of the medium

•

Abrasionandmechanicalinuences

The mounting position and orientation of the sensor must take into ac-

count the limitations in chapter "For your safety", "Radio approval for

USA" "RadioapprovalforCanada" of this operating instructions.

4.2 Mounting versions, plastic horn antenna

The optional mounting strap allows simple mounting of the instrument

on a wall, ceiling or boom. Especially in the case of open vessels, this

Protection against mois-

ture

Process conditions

Radio license for USA/

Canada

Mounting strap

16

4 Mounting

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

isasimpleandeectivewaytoalignthesensortothesurfaceofthe

bulk solid material.

The following versions are available:

•

Length 300 mm

•

Length 170 mm

The instrument is normally mounted vertically with a bracket on the

ceiling.

This allows swivelling the sensor up to 180° for optimal orientation

and rotating for optimal connection.

Fig.3:Ceilingmountingviathemountingstrapwithlength300mm

Asanalternativethestrapmountingiscarriedouthorizontallyor

obliquely.

> 200 mm

(7.87")

Fig. 4: Wall mounting horizontally via the mounting strap with length 170 mm

Mounting strap - Ceiling

mounting

Mounting strap - Wall

mounting

17

4 Mounting

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

Fig. 5: Wall mounting with inclined wall via the mounting strap with length

300 mm

Two versions are available for mounting the instrument on a socket:

•

Combicompressionange

•

Adapterange

Combicompressionange

Thecombicompressionangeissuitablefordierentvesselanges

DN 80, ASME 3" and JIS 80. It comes not sealed against the radar

sensorandcanthusonlybeusedunpressurized.Itcanberetrotted

oninstrumentswithsinglechamberhousing,retrottingtoadouble

chamber housing is not possible.

1

Fig.6:Combicompressionange

1 Combicompressionange

Adapterange

TheadapterangeisavailablefromDN100,ASME4"andJIS100.It

is permanently connected with the radar sensor and sealed.

Flange

18

4 Mounting

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

3

1

2

Fig.7:Adapterange

1 Connectionscrew

2 Adapterange

3 Process seal

4.3 Mounting preparations, mounting strap

The mounting strap is supplied unassembled (optionally) and must be

screwed to the sensor before setup with three hexagon socket screws

M5 x 10 and spring washers. Max. torque, see chapter "Technical

data".Requiredtools:Allenwrenchsize4.

Therearetwodierentvariantsofscrewingthestraptothesensor,

see following illustration:

1 2

Fig. 8: Mounting strap for screwing to the sensor

1 For angle of inclination in steps

2 Forangleofinclination,innitelyvariable

Depending on the selected variant, the sensor can be rotated in the

strap:

•

Single chamber housing

– Angle of inclination in three steps 0°, 90° and 180°

– Angleofinclination180°,innitelyvariable

•

Double chamber housing

– Angle of inclination in two steps 0° and 90°

– Angleofinclination90°,innitelyvariable

19

4 Mounting

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

Fig. 9: Adjustment of the angle of inclination

Fig. 10: Turning by fastening in the centre

4.4 Mounting instructions

Radar sensors for level measurement emit electromagnetic waves.

Thepolarizationisthedirectionoftheelectricalcomponentofthese

waves.

Thepolarizationdirectionismarkedbyanoseonthehousing,see

following drawing:

1

Fig. 11: Position of the polarisation

1 Nose for marking the direction of polarisation

Note:

Whenthehousingisrotated,thedirectionofpolarizationchanges

andhencetheinuenceofthefalseechoonthemeasuredvalue.

Please keep this in mind when mounting or making changes later.

Mount the sensor at least 200 mm (7.874 in) away from the vessel

wall.

Polarisation

Installation position

20

4 Mounting

VEGAPULS 69 • Two-wire 4 … 20 mA/HART

47247-EN-200427

200 mm

(7.87

")

Fig. 12: Mounting the radar sensor on the vessel top

If you cannot maintain this distance, you should carry out a false

signal suppression during setup. This applies particularly if buildup on

the vessel wall is expected. In such cases, we recommend repeating

the false signal suppression at a later date with existing buildup.

Theinstrumentshouldnotbemountedtooclosetotheinowing

medium, as the radar signal could be disrupted.

Silowithllingfromtop

Theoptimalmountingpositionisoppositethellingaperture.Toavoid

heavysoiling,thedistancetoanylterordustexhaustershouldbeas

large as possible.

Fig.13:Mountingoftheradarsensorwithinowingmedium

Silowithlaterallling

Inbulksolidssiloswithlateralpneumaticllingtheinstrumentshould

notbemountedabovethellingstream,astheradarsignalwillbe

disrupted.Theoptimalmountingpositionistothesideofthelling

aperture.Toavoidheavysoiling,thedistancetoanylterordust

exhauster should be as large as possible.

Inowingmedium

Page is loading ...

Vega VEGAPULS 69 Operating instructions

Vega VEGAPULS 69 Operating instructions

Related papers

Other documents