Anolis Ambiane™ User manual

Brand: Anolis

Model: Ambiane™

Category: Stroboscopes & disco lights

Type: User manual

Anolis Ambiane™ is a professional-grade LED lighting fixture designed for indoor use. It offers a wide range of features and capabilities, making it suitable for a variety of applications, including architectural, retail, and hospitality lighting.

Ambiane™ generates colored light using high-power LEDs and can be controlled via DMX, DALI, or 0-10V protocols. It also supports RDM (Remote Device Management), allowing for easy configuration and monitoring of the fixture.

The fixture features a robust aluminum housing and a wide beam angle of 67°, making it ideal for general illumination and creating ambient light. It also comes with an anti-glare ring and a diffuser glass, which can be used to reduce glare and create a more diffused light output.

User manual

Ambiane TD

The unit generates colored light by means of high power LEDs. The product was designed for indoor use only.

1. Attention

  Theunitmustbeinstalledbyaqualiedelectricianinaccordancewithall

national and local electrical and construction codes and regulations.

The unit was designed for indoor use only.

Avoid looking directly into the LED light beam at close range!

  Donotinstalltheunitnearhighlyinammableliquidsormaterials.

Do not allow anything to rest on the unit.

  Donotinstalltheunitnearanopename.

Do not install the unit in dirty,dusty or badly ventilated location.

  Sucientairaccessingtothehousingoftheunithastobeensured,

there must not be any heat or anti-noise insulation within a 0.6m x 0.6m

  areaaroundtheunit(non-ICratedxture).

Suitable for fastening on Unsuitable for covering by heat insulation

 non-ammablesurfacesonly  material

2. Installation

1.Prepareacircularopeninginthelowerceiling(1)asshowninthepicturebelow.

2.InserttheAmbianeunitintotheopening.Fastenthexturebymeansoftwospringfasteners(2)totheopening

Alvays switch o power suply of the unit before connecting or disconnecting the unit

Toconnectneededcablestothexture,unscrewtwoscrews(4)fromtheplasticcover(3)andchipneeded

plasticthin-walledcovers(6)oinordertopasscablestotheconnectionblocks(5).

Theconnectionblocks(5)havethefollowingwiring:

Theprimarypowerinputservesforastandardpower(e.g.ArcPowerforAmbiane).

Thesecondarypowerinputservesforabackuppower(incasethatprimarypowerfailed).

If both power inputs are under voltage, the primary power has a priority and the secondary power is disabled.

fthextureissuppliedviathesecondarypower,thelightoutputofthextureisawhitecolour(3200K)andits

light intensity can be set by a trimmer.

Thexturecanbecontrolledbyoneofthefollowingmethods:DMX512

0-10V

DALI

ThextureisequippedwithtwoDMXandDALIconnectionblocksforeasyconnectiontoDMXorDALIchain

(In/Outmethod).

DMX connection 0-10V connection Power connection

PCB Function PCB Function PCB Function

0V - Shield 0V 0V + Power +

D+ Signal(+)   D+ +10V    - Power-

D- Signal(-)

3. DMX and DALI address setting and control

The DIP switch, located next to the connection blocks, allows to set a method of control, run test and also allows

toswitchthexturetotheupdatemodeincaseofsoftwareupdate.

DIP10-ifswitchedtoON=testlight(thexturelightsat3200K)

DIP11-selectionofxturecontrol:OFF=DMX512orDALI,ON=0-10V

DIP12-changefromOFFtoONpositionswitchesthexturetotheupdatemode(switchingtotheupdate

modeisnotnecessaryIftheRobeUploaderisusedforxtureupdate).

DMX control

TheDMXstartaddress,istherstchannelusedtoreceiveinstructionsfromtheDMXcontroller.Theaddress

maybeanychannelfrom1to512.DMXaddresscanbeseteitherbyDIPswitchorbyRDM.DMXaddress

setbyRDMoverwritesaddresssetbyDIPswitchandviceversa.ThegreenLEDonPCBsignalswayofDMX

addresssetting:

 LEDlights-DMXaddressissetbymeansoftheDIPswitch.

 LEDdoesnotlight-DMXaddressissetbymeansofRDM.

DIP 11 has to be set in OFF position.

ExampleofDMXaddresses:

DALI control

AddressingofthextureismadebymeansofanexternalDALIcontroller.TheexternalDALIcontrollerhasto

sendactivatingcommand(8=ON)ifyouneedtostartthepermanentcontrolofthexture(xturewillnotrespond

toDMXcommands)anddeactivatingcommand(0=OFF)tostopcontrolofthexture.

DIP 11 has to be set in OFF position.

Note:IfDIP11=OFF(xtureiscontrolledbyDMXorDALI),therstcomingcommandswitchesthexturetothe

correspondingoperationmode(DMXoperationbyaDMXcommand,DALIoperationbyaDALIcommand).E.g.

thexturestaysinaDALIoperationandcomingDMXcommandswitchesthexturetoDMXoperation.Next

commandisaDALIcommandandswitchesthexturetotheDALIoperationetc.Ifyouneedthepermanent

DALIoperation,youhavetosendaDALIcommand8tothexture.

0-10V control

DIP 11 has to be set in ON position. 0-10V operation has priority to DALI commands.

4. RDM

ThisxturesupportsRDMoperation.RDM(RemoteDeviceManagement)isabi-directionalcommunication

protocolforuseinDMX512controlsystems,itisthenewopenstandardforDMX512devicecongurationand

status monitoring.

RDMallowsyoutosetDMXaddress,selectDMXmodeandreadoutsoftwareversionofthexture.

5. Anti-glare ring installation

Inserttheantiglarering(1)intothextureuntilthreelocks(2)snapintoslots(3).

6. Adapter ring installation

1.Removebothspringfasteners(2)byunscrewingthefourscrewsM4x10(1).

2.Slidetheadapterring(4)ontothehousingofthexture.Screwthenewfasteners(3)onthehousing.

UseoriginalscrewsM4x10(1).

7. DMX protocol

version 1.1

Mode 1

Channel

Mode 2

Channel

Value Function Type of control

1 1

0-255

Dimmer

Light intensity coarse 0% -->100% proportional

- 2

0-255

Dimmer Fine

Light intensity from min. -->max. proportional

8. Technical specications

Inputvoltage:     24VDC

Max.powerconsumption:   40W

Protectionclass:    CE: (ClassIII)

      ETL:Class2orLVLE

Beamangle:     67°,80°withanti-glarering

Colourtemperature:    3200K

Control:     DMX,DALI,0-10V,RDMcompatible

DMXchannels:     1(Mode1),2(Mode2)

TypicalLumenmaintenance:   70%@50,000hours

Ledlifeexpectancy:    minimum50,000hours

Operatingambienttemp.range:  -20°C/+45°C(-4F/+113F)

Operatingtemperature:   75°C@Ambient+35°C(167°F@Ambient+95°F)

Cooling:     convection

Totalheatdissipation:    136BTU/h(calculated)

Housing:     alluminium

Weight:     1.8kg

Installationmethod:    viatwospringfasteners

ICrating:     non-ICrated

Power/DMX/DALIconnection:   screwconnectionblockDegsonDG306-5.0-02P

      (Wirerange:22-14AWG(UL),1.5mm

(IEC))

Max.distancebetweenAmbianeand

ArcPowerforAmbiane:   1m(for2x18AWGcable)

Protectionfactor:    IP20(withoutdiuserglass),IP20/IP54(withDiuserGlass)

AmbianewithoutDiuserGlass    AmbianewithDiuserGlass

9. Optional Accessories

ArcPowerforAmbiane(P/N10063035)

Anti-GlareRing(P/N10980386)

DiuserGlassFrosted(P/N10980387)

AdapterRing(230-255mm)(P/N10980388)

10. Maintenance

Keepthextureclean,especiallylightsourceandtheribbedhousing.

11. Dimensions

mm [inch]

12. Software update

Software update by means of the DSU le.

Thefollowingitemsarerequiredinordertoupdatesoftware:

-PCrunningWindowsorLinuxormacOS

-DSUle

-FlashcableRS232/DMX(P/N13050624)ortheRobeUniversalInterface/RobeUniversalinterfaceWTX.

Toupdatesoftwareinthexture:

1.DSUleisavailablefromAnoliswebsiteathttps://www.anolislighting.com/

FilewithextensionzipisintendedforWindows(usedandtestedfromXPtoW10on32/64bitsystems).

FilewithextensiontbzisintendedforLinux(usedandtestedonDebianandUbuntu32/64bit).

File with extension dmg is intended for

macOS(usedandtestedonOSXuptoSierra)XQuartzrequired,

installitfromhttps://www.xquartz.org/

Savethedownloadletoafolderonyourcomputer.

Incasethatyouusewindows,extractlesintheziple(e.g.DSU_Ambiane_18051040.zip)

2.SwitchthextureoanddisconnectthexturefromDMXcontroller(IfyouuseDALIcontrol,switcho

theDALIcontroller).

3.IfyouusetheashcableRS232/DMX,connectaserialportofyourcomputerwithDMXinputofthexture

bymeansofthiscable(probablyyouwillneedsomeUSBtoRS232converterifyourcomputerhas

USBportsonly).

IfyouusetheRobeUniversalInterface,connectaUSBportofyourcomputerwiththeRobeUniversalInterface

bymeansoftheUSBcableandDMXinputofthexturewiththeDMXoutputoftheRobeUniversalInterface

viaaDMXcable.

4.Switchthextureonandswitchittotheupdatemode(svitchthe

DIP12fromOFFtoONposition)

Werecommendtocancelallrunningprogramsonyourcomputerbeforestartingthesoftwareuploader.

5.Double-clickthesoftwareuploaderle(e.g.DSU_Ambiane_18051040.exe)in

theextractedles.TheSoftwareUploaderprogramwillstartrunning.

6.Selectcorrect"COM"numberifyouusea

FlashcableRS232/DMX

or select "

Robe Universal Interface "

if you use the

RobeUniversalInterface/RobeUniversalInterfaceWTX

and then click on the "Connect" button.

7.IftheconnectionisOK,clickthe“StartUploading"buttontostartsoftwareuploading.Itwilltakeseveral

minutes to perform software update.

If the option "Incremental Update" is not checked, all processors will be updated (including processors with

thesamesoftwareversion).

Ifyouwishtoupdateonlyprocessorswithnewversionofsoftware,checkthe“IncrementalUpdate

box“.

Avoidinterruptingtheprocess.Updatestatusisbeingdisplayedinthe"InfoBox"window.

Whentheupdateisnished,thelinewiththetext“Fixtureissuccessfullyupdated“willappearin

this window.

8.SwitchthextureoandsettheDIP12toOFFposition.

Incaseuploadprocessisinterrupted(e.g.powerloss),thexturestaysin“Updatingmode”andyouwillhave

to repeat the software update again.

Software update by means of the Robe Uploader

Anotherway,howtoupdatesoftwareinthextures(especiallylargeinstallationofxtures)istousetheROBE

Uploader.ItisasoftwareforautomatizedsoftwareupdateofRobeandAnolisxtures.Itcantakeadvantageof

RDMsupportandEthernetportsifpresentintheunits.

Thextureshastobeconnectedinadaisy-chain(max.32xtures)andvia

the

Robe Universal Interface/Robe

UniversalInterfaceWTX

andaUSBcableconnectedtothecontrolPCwiththeRobeUploaderrunning.

The control PC should be connected to the Internet.

TheRobeUploadersoftwareandusermanualisavailableat:

https://www.robe.cz/robe-uploader/

Note:

IfyoudothesoftwareupdatebymeansoftheRobeUploader,switchingxturestotheupdatemode(andfrom

theupdatemode)ismadeautomatically,withoutneedtoswitchtheDIP12toONposition.

TheRobeUploadersoftwarecannotbeusedifxturesareconnectedbymeansofDALIconnection.

Version 2.0 September, 2018

Specications are subject to change without notice.

Made in CZECH REPUBLIC by ROBE LIGHTING s.r.o. Palackeho 416/20 CZ 75701 Valasske Mezirici

Anolis Ambiane™ User manual

Brand: Anolis

Model: Ambiane™

Category: Stroboscopes & disco lights

Type: User manual

Download PDF

report

Anolis Ambiane™ User manual

Anolis Ambiane™ User manual

Related papers

Other documents