Smith Blair Inc 26100066307000 Installation guide

Brand: Smith Blair Inc

Model: 26100066307000

Type: Installation guide

Installation

Instructions

261, 262, 263, 264, 265, 269, & 281

Full Circle

Repair Clamp (Fabricated Lugs)

Questions: Call 1-800-643-9705 or visit www.smith-blair

.com

Sheet 1 of 2 Rev 8/29/19

Water

TI-008

STEP 1

Thoroughly clean the pipe where the

clamp will be installed. Be sure to remove

any scale, dirt, or debris that could affect

the gasket seal.

STEP 2

Mark the pipe in both directions a

measured distance from the center of the

break or damaged area.

STEP 3

Loosen the nuts to be flush with the top of

the studs and place the clamp around the

pipe, centered over the break or damaged

area, with the gasket flap at the top. Note:

For optimum product performance, the

fitting should be lubricated with a suitable

lubricant.

STEP 4

Tuck the gasket flap in place and mesh the

lug fingers by pulling the keeper bar

upward and snapping the lip over the

finger weldment base. Tighten hand-tight.

Note: The clamp may be assembled beside

the break or damaged area and slid into

position if the pipe surface is wet or has

been lubricated.

PRE-INSTALL NOTES

When a gap between the ends of the pipes is 1” or

greater, a short section of pipe should be put in the

opening or a thin strip of sheet metal should be

wrapped around it to provide support to the gasket.

Use discretion on larger O.D. pipes.

When a section of pipe wall equal to 40% or more of

the pipe circumference is broken away, a section of

sheet metal should be placed over the opening to

provide a sealing surface for the gasket. Use of a

clamp that extends 3” past the sheet metal on both

sides axially is required.

STEP 5

Rotate the clamp away from gasket taper

to ensure proper seating of the gasket,

and position the bolts and nuts for

convenient tightening.

STEP 6

Tighten the nuts working form the center

outward without exceeding torque

values listed below. Note: Completely

tightening the center nut(s) will usually

stop or sufficiently slow the leakage to

simplify completion of the installation.

STEP 7

When the nuts have been tightened

sufficiently to stop the leakage, check

reference marks to assure clamp is still

properly centered over break or

damaged area. Loosen nuts and

reposition clamp if necessary. For

multi-band clamps, maintain similar

gaps between bands while tightening.

STEP 8

Recheck the tightness, and torque the

nuts as evenly as possible to the

recommended torque values listed

below.

Recommended Torque Values

Pipe Size

Torque

Through 4.73” O.D.

50 ft-lbs

Above 4.73” O.D.

70 ft-lbs

*Do not exceed recommended torque*

264/265 INSTALL NOTES

Do not tap through clamps. These products

are intended for use on repair applications

and applications involving a pre-drilled pipe.

NOTE: Use of a calibrated torque

wrench is recommended!

Installation

Instructions

261, 262, 263, 264, 265, 269, & 281

Full Circle

Repair Clamp (Fabricated Lugs)

Questions: Call 1-800-643-9705 or visit www.smith-blair

.com

Sheet 2 of 2 Rev 8/29/19

Water

TI-008

ARRANTY

Smith-Blair

warrants its products only against defects in materials and workmanship. Smith-Blair’s liability

and customer’s exclusive remedy under this warranty or any warranty extends for a period of one (1) year

from the date of Smith-Blair’s ship date and is expressly limited to repayment of the purchase price, repair or

replacement, at Smith-Blair’s option, during said period, upon proof satisfactory to Smith-Blair

and upon

customer’s returning and prepaying all charges on such products to factory or warehouse designated by

Smith-Blair.

This warranty is made expressly in lieu of all other warranties, expressed, implied or statutory with respect to

quality, merchantability or fitness for a particular purpose.

10/11

Metal products are subject to corrosion, particularly when used outdoors and/or underground. A large

number of factors and local conditions af the rate of corrosion. Consult a local corrosion expert

determine the life expectancy of this product when used with your pipeline content, soil, and environment.

Also, consult your system designer to determine the suitability of this product in your piping system. Failure

to determine the suitability of this product in your application, soil, and/or environment can result in premature

product failure. Smith-Blair

will provide additional information about this product’s material specifications at

your request. You may also obtain product information at www.smith-blair .

2/17

Special Installation Notes for Installation of Type(s)

261, 262, 264, and 265 Full Circle® Repair Clamps

on Polyethylene Pipe

[Not for Gas Service]

Smith-Blair® Belleville

Washers (p/n 150115-000)

must be used on PE pipe

installations. Use of any

other type of Spring Washer

may cause product failure.

WARNING

DO NOT EXCEED TORQUES LISTED BELOW

 Through 3.50” O.D. = 30 ft-lbs

 Above 4.00” O.D. = 50 ft-lbs

See Smith-Blair HDPE Application Guide for recommended

size(s) and DR(s) clamps are approved for use on

Smith Blair Inc 26100066307000 Installation guide

Smith Blair Inc 26100066307000 Installation guide

Smith Blair Inc 26100066307000 Installation guide

Related papers

Other documents