2. Airaid
  3. 310-508

Airaid 310-508 Installation guide

  • Hello! I'm your chat assistant. I've reviewed the installation instructions for the AIRAID 310-508 Throttle Body Spacer, designed for 2004-06 Jeep Liberty 3.7L vehicles. This document provides a detailed guide including parts list, tools list, and the necessary steps to install the device. I am ready to assist you with any questions you have about the installation process or the product itself.
  • What should I do if I have missing parts?
    Where should I place the C.A.R.B. sticker?
    What should I do before driving after installation?
1
# 310-508 INSTALLATION INSTRUCTIONS
2004 -06 Jeep Liberty 3.7L
Parts List
(1)- Power Plate
(1)- “O” Ring #238
(1) Throttle Cable Bracket
(2) 3/8”ID x 3/4”OD x .636 O.A.L. Spacers
(1) Nutplate with 3/8-16” threads
(2) 3/8-16” x 1 1/2” Hex head bolts
(3) 6mm x 50mm Hex Head Bolts
(3) 6mm Flat Washers
Tools List
Flat Head Screwdriver
14mm Socket
10mm Socket
8mm Socket
Ratchet & Extension
Thank you for purchasing the PowerAid Throttle Body Spacer. Please read the
instruction manual carefully before proceeding with the installation. Contact AIRAID @
(800) 498-6951 8:00 AM - 5:00 PM MST Weekdays for questions regarding fit or in-
structions that are not clear to you. Your PowerAid Throttle Body Spacer was carefully
inspected and packaged. Check that no parts are missing, or were damaged during
shipping. If any parts are missing, please contact AIRAID.
Thank you for selecting AIRAID.
Included with your Poweraid Spacer is a sticker with a California Air Resources Board
(C.A.R.B.) Executive Order (EO) number. This sticker must be placed in plain view inside of
the engine compartment. Failure to do so may prevent you from passing a smog inspection.
2
Installation Instructions. Read Me!
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove throttle body air intake.
3. Remove (3) bolts from the throttle body.
4. Unclip throttle & cruise cables and remove from manifold and throttle lever.
5. Install furnished throttle & cruise cable bracket and tighten bolts. (Ref. “B”)
6. Install both throttle & cruise cables thru reinforcement ring of throttle cable bracket. Slide and lock both plastic
cable retainers into slot separately.
7. Install “O” ring into groove of power plate.
8. Install power plate using (3) 6mm x 50mm bolts and washers. (Ref. “A” & Step 4)
9. Reattach cruise & throttle cables to throttle body lever.
10. Inspect & Test throttle linkage for full Open & Closed travel before driving. Some cruise and kick down cables
may require adjustment. Please refer to your vehicles service manual for proper adjustment.
11. Reinstall throttle body air intake assembly using Step 2 as an example.
12. Reconnect negative battery cable. Enjoy!
The sound of power...The “whistle” means its working!
ASSEMBLY DETAIL (Ref. “B”)
Ref. “B”- (1) Throttle Cable Bracket
(2) 3/8 ID x 3/4 OD x .636 Spacers
(1) Nutplate with 3/8-16” threads
(2) 3/8-16”x 1 1/2” Hex Head Bolts
Ref. “A”- (1) Power Plate
(1) O-ring #238
(3) 6mm x 50mm Bolts
(3) 6mm Flat Washers
Bracket
(2) Spacers
Nutplate
AIRAID Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 [email protected] www.airaid.com
Rev. 11-08-06
/