Airaid 310-515 Installation guide

Brand
Airaid
Model
310-515
Type
Installation guide

Airaid 310-515 is a Throttle Body Spacer designed for 1999-2002 Jeep Grand Cherokee 4.7L. It is easy to install and can be done with basic tools. The spacer is made of high-quality materials and comes with all the necessary hardware for installation.

The Airaid 310-515 Throttle Body Spacer is designed to improve airflow and throttle response. It does this by increasing the distance between the throttle body and the intake manifold. This allows for more air to flow into the engine, which results in increased power and torque. The spacer also helps to reduce intake air temperature, which can further improve engine performance.

Airaid 310-515 is a Throttle Body Spacer designed for 1999-2002 Jeep Grand Cherokee 4.7L. It is easy to install and can be done with basic tools. The spacer is made of high-quality materials and comes with all the necessary hardware for installation.

The Airaid 310-515 Throttle Body Spacer is designed to improve airflow and throttle response. It does this by increasing the distance between the throttle body and the intake manifold. This allows for more air to flow into the engine, which results in increased power and torque. The spacer also helps to reduce intake air temperature, which can further improve engine performance.

1
# 310-515 INSTALLATION INSTRUCTIONS
1999-2002 Jeep Grand Cherokee 4.7L
Parts List
(1)- Power Plate
(1)- “O”-Ring #240
(3)- Hex Bolts 6mm x 60mm
(5)- Flat Washers 6mm
(2)- Air Box Extension Plates
(2)- Hex Bolts 6mm x 20mm
(3)- Throttle Bracket Extension Plates (Special)
(3)- Flat Head Screws 6mm x 20mm
* Also available for your Jeep Grand Cherokee–
the Airaid Intake System P/N 310-127.
Call for details!
Tools List
1/4 in. Ratchet
1/4 in. x 12 in. Extension
10mm Socket
14mm Socket
14mm Box End Wrench
3/16 Allen Wrench
5/32 Allen Wrench
7/8 Box End Wrench
Thank you for purchasing the Poweraid Throttle Body Spacer. Please read the
instruction manual carefully before proceeding with the installation. Contact AIRAID @
(800) 498-6951 8:00 AM - 5:00 PM MST Weekdays for questions regarding fit or in-
structions that are not clear to you. Your Poweraid Throttle Body Spacer was carefully
inspected and packaged. Check that no parts are missing, or were damaged during
shipping. If any parts are missing, please contact AIRAID.
Thank you for selecting AIRAID.
2
Installation Instructions. Read Me!
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove air intake assembly.
3. Remove throttle body intake box and save bolts.
4. Remove (3) bolts from throttle body.
5. Remove bolts from throttle linkage bracket and save.
6. Install power plate using (3) 6mm x 60mm bolts and flat washers (Ref. “A”).
7. Locate (3) extension plates and (3) flat head screws before installing throttle linkage and dipstick
bracket. (* Note: Remove stud from front throttle linkage mount.) Dipstick must be located under
forward extension plate at flathead screw location (Ref. “B”).
8. Locate (2) extension plates using (2) 6mm bolts & washers to reposition throttle body intake box
using saved bolts (Step 2) & (Ref. ”C”).
9. Inspect & Test throttle linkage for full open and closed travel before driving. Some cruise or kick-
down cables may require adjustment. Please refer to service manual.
10. Reinstall throttle body air intake assembly using (Step 1) as an example.
11. Reconnect battery cable. Enjoy!
The sound of power...The “whistle” means its working!
Ref. A- (1) Power Plate
(1) “O” Ring #240
(3) Bolts 6mm x 60mm
(3) Flat Washers 6mm
Ref. B- (3) Extension Plates (Short)
(3) 6mm Flat Head Screws
Ref. C- (2) Air Box Extension Plates
(2) Bolts 6mm x 20mm
(2) Flat Washers 6mm
AIRAID Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 [email protected]m www.airaid.com
Rev. 11-08-06
  • Page 1 1
  • Page 2 2

Airaid 310-515 Installation guide

Brand
Airaid
Model
310-515
Type
Installation guide

Airaid 310-515 is a Throttle Body Spacer designed for 1999-2002 Jeep Grand Cherokee 4.7L. It is easy to install and can be done with basic tools. The spacer is made of high-quality materials and comes with all the necessary hardware for installation.

The Airaid 310-515 Throttle Body Spacer is designed to improve airflow and throttle response. It does this by increasing the distance between the throttle body and the intake manifold. This allows for more air to flow into the engine, which results in increased power and torque. The spacer also helps to reduce intake air temperature, which can further improve engine performance.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents