Airaid 310-510 Installation guide

Type
Installation guide

Airaid 310-510 is a throttle body spacer designed to improve airflow and performance in 1991-2006 Jeep TJ,YJ Wrangler and XJ Cherokee 4.0L vehicles.

Installing the Airaid 310-510 throttle body spacer can provide several benefits, including:

Increased airflow: The spacer raises the throttle body, allowing for more air to enter the engine. This can result in improved power and torque, especially at low and mid-range RPMs.

Improved throttle response: The increased airflow can also lead to improved throttle response, making the engine more responsive to driver input.

Easy installation: The Airaid 310-510 throttle body spacer is designed for easy installation. It comes with all the necessary hardware and gaskets, and can be installed in under an hour using basic hand tools.

Airaid 310-510 is a throttle body spacer designed to improve airflow and performance in 1991-2006 Jeep TJ,YJ Wrangler and XJ Cherokee 4.0L vehicles.

Installing the Airaid 310-510 throttle body spacer can provide several benefits, including:

Increased airflow: The spacer raises the throttle body, allowing for more air to enter the engine. This can result in improved power and torque, especially at low and mid-range RPMs.

Improved throttle response: The increased airflow can also lead to improved throttle response, making the engine more responsive to driver input.

Easy installation: The Airaid 310-510 throttle body spacer is designed for easy installation. It comes with all the necessary hardware and gaskets, and can be installed in under an hour using basic hand tools.

1
# 310-510 INSTALLATION INSTRUCTIONS
1991-2006 Jeep TJ,YJ Wrangler
XJ Cherokee 4.0L
Parts List
AIR-KIT510PA Aluminum Plate (1)
AIR-KIT510G Gasket (2)
AIR-KIT510H Hardware
BOLTS 6MM X 50MM (4)
WASHERS (4)
BOLTS 6MM X 40MM (3)
SPACERS 1” (3) Tools List
10 mm Socket or Wrench
Ratchet & Extension
* Also available for your Jeep Cherokee/
Wrangler– the Airaid Intake System.
Call for details!
Thank you for purchasing the PowerAid Throttle Body Spacer. Please read the
instruction manual carefully before proceeding with the installation. Your PowerAid
Throttle Body Spacer was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If you need any assistance please call 1-
800-858-3333 to speak with a representative in our Customer Service Center before
returning the product. Thank you for selecting AIRAID.
Included with your Poweraid Spacer is a sticker with a California Air Resources Board
(C.A.R.B.) Executive Order (EO) number. This sticker must be placed in plain view inside of
the engine compartment. Failure to do so may prevent you from passing a smog inspection.
INTAKE SYSTEMS FOR VEHICLES LISTED ARE 50 STATE
LEGAL. SEE AIRAID.COM FOR CARB STATUS ON EACH
PART FOR A SPECFIC VEHICLE.
2
Installation Instructions. Read Me!
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove throttle body air intake assembly.
3. Remove (4) bolts from throttle body (Ref. “A”).
4. Remove gasket and clean surfaces.
5. Install Power plate with (2) gaskets (Ref. “B”).
a. One gasket located between throttle body and power plate.
b. One gasket located between power plate and manifold.
6. Replace (4) bolts (Ref. “A”) using (Step # 3) as an example.
7. Locate and install (3) spacers under linkage bracket (Ref. “C”) using (3) 6mm x 40mm bolts.
8. Inspect & Test throttle linkage for full open & closed travel before driving.
Some cruise or kick down cables may require adjustment. Refer to service manual.
9. Reinstall throttle body air intake assembly using (Step # 3) as an example.
10. Double check your work. Reconnect the battery cable. ENJOY!!
The sound of power...The “whistle” means its working!
Ref. C- (3) Spacers 1”
(3) 6mm x 40mm Bolts
Ref. A- (4) Bolts 6mm x 50mm
(4) Washers 6mm
Ref. B– Poweraid Plate
(2) Gaskets
AIR-I31510B
Rev. 12.22.16
Airaid. 1815 West Crest Lane. Phoenix AZ 85027 (800) 498-6951 Air[email protected] www.airaid.com
  • Page 1 1
  • Page 2 2

Airaid 310-510 Installation guide

Type
Installation guide

Airaid 310-510 is a throttle body spacer designed to improve airflow and performance in 1991-2006 Jeep TJ,YJ Wrangler and XJ Cherokee 4.0L vehicles.

Installing the Airaid 310-510 throttle body spacer can provide several benefits, including:

Increased airflow: The spacer raises the throttle body, allowing for more air to enter the engine. This can result in improved power and torque, especially at low and mid-range RPMs.

Improved throttle response: The increased airflow can also lead to improved throttle response, making the engine more responsive to driver input.

Easy installation: The Airaid 310-510 throttle body spacer is designed for easy installation. It comes with all the necessary hardware and gaskets, and can be installed in under an hour using basic hand tools.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI