Humandata EDX-301 User manual

Brand
Humandata
Model
EDX-301
Type
User manual
HuMANDATA LTD.
Spartan-6 USB-FPGA Board
EDX-301
User’s Manual
Ver. 1.0
Table of Contents
z Revision History ................................................................................................. 1
z Introduction ........................................................................................................ 1
1. Specifications ......................................................................................................... 2
2. Overview ................................................................................................................ 3
2.1. Name of Parts .................................................................................................... 3
2.2. Block Diagram ................................................................................................... 4
2.3. 7 segment LED .................................................................................................. 4
2.4. Clock ................................................................................................................... 5
2.5. Power Supply ..................................................................................................... 5
2.6. I/O Power Supply ............................................................................................... 5
2.7. USB Controller .................................................................................................. 6
2.8. Device Driver ..................................................................................................... 7
2.9. Setting Switch (SW1) ........................................................................................ 7
3. FPGA Configuration .............................................................................................. 8
3.1. Using Original Tool ............................................................................................ 8
3.2. Using JTAG Download cable ............................................................................. 8
3.3. Using Configuration Device .............................................................................. 9
4. Factory Setting of FT2232H EEPROM ................................................................. 9
5. Documentation and User Support ........................................................................ 10
Precautions
Do Not
1. This product uses ordinary off-the-shelf electronic components, and is therefore inappropriate for use in
applications that require special quality or reliability and are expected to protect human lives or prevent
accidents, such as safety mechanisms in fields including space, aeronautics, medicine, and nuclear
power.
2. Do not be used underwater or in high-humidity environments.
3. Do not be used in the presence of corrosive gases, combustible gases, or other flammable gases.
4. Do not turn on power when circuit board surface is in contact with other metal.
5. Do not apply voltage higher than rated voltage.
Attention
6. This manual may be revised in the future without notice owing to improvements.
7. All efforts have been made to produce the best manual possible, but if users notice an error or other
problem, we ask that they notify us.
8. Item 7 notwithstanding, HuMANDATA cannot be held liable for the consequences arising from use of
this product.
9. HuMANDATA cannot be held liable for consequences arising from using this product in a way different
from the uses described herein, or from uses not shown herein.
10. This manual, circuit diagrams, sample circuits, and other content may not be copied, reproduced, or
distributed without permission.
11. If the product emits smoke, catches fire, or becomes unusually hot, cut the power immediately.
12. Be careful of static electricity.
13. This product may be subject to the export restrictions of Japan, the United States, or other countries.
Purchasers are responsible for properly observing export restrictions.
14. HuMANDATA firmly refuses to export (including reexporting) products to countries or regions subject to
export restrictions.
Product Warranty and Scope of Support
1. HuMANDATA guarantees that its products can be assembled as shown in published circuit diagrams and other design documents.
There may be differences between actual components or their prescribed quantities and model numbers and those shown in circuit
diagrams.
2. Except for the guarantee in item 1, above, no guarantees whatsoever are made. When assembling the product as shown in a circuit
diagram is impossible, and the problem can be solved by revising the diagram, HuMANDATA will revise the diagram. When a
problem can be solved only by replacing components or modifying the product, HuMANDATA will take back the product to replace it
with a properly functioning product.
3. If the problem is minor, HuMANDATA will sometimes describe how to make the revision or modification, and ask the customer to
solve the problem.
4. HuMANDATA will determine how to honor the warranty, as through repair, replacement, return, or other action. The customer cannot
specify what action to take.
5. FPGAs and other components used in products sometimes have characteristic defects. Returns and replacements are not possible
even if such defects are discovered, whether before or after purchase.
6. HuMANDATA shall not be obligated to inform customers about defects in the main components used in products.
7. HuMANDATA shall not be obligated to provide support for products, or to provide support for the software of other companies
needed to use HuMANDATA products.
8. Published documentation shall be limited to that published by HuMANDATA at the time of product purchase, and HuMANDATA shall
not be obligated to provide any other documentation.
9. When repairs or replacements are provided under warranty in Japan, purchaser shall pay shipping charges for shipping to
HuMANDATA, and HuMANDATA shall pay shipping charges for shipping to purchaser.
10. When shipping from outside of Japan, purchaser shall pay all expenses including shipping charges and taxes.
11. Under whatever circumstances, HuMANDATA shall provide support for its products for a maximum of one year after shipping from
factory.
12. The Warranty is not applicable and support ends in the event of fire, storm and flood damage, earthquakes, lightning strikes, and
other natural disasters, as well as conflict or other occurrences.
13. Purchaser is assumed to have read and understood all the above when purchasing a HuMANDATA product.
Limitation of Liability
1. Purchasers assume all liability associated with the use of this product.
2. HuMANDATA assumes no liability whatsoever for any direct, indirect, special, incidental, or consequential damages arising from the
use of this product, even if HuMANDATA has been advised of the possibility of such damage, whether legal or in tort.
3. At the time this product is purchased, items 1 and 2 above shall be deemed to have been confirmed by purchaser.
Trademarks and Other Considerations
1. This manual uses various companies’ trademarks in places.
2. HuMANDATA is this company’s registered trademark.
HuMANDATA’s Philosophy
1. HuMANDATA endeavors to raise product quality. We continually make detailed improvements and adjustments that are not shown
in circuit diagrams.
2. HuMANDATA actively publishes, on the Web and in other ways, information considered useful to customers. Examples would be
how to use FPGAs and how to use development tools.
3. HuMANDATA makes efforts for the long-term provision of products and for continuing their long-term support.
4. Instead of concealing small product problems and documentation errors, HuMANDATA makes them public.
5. HuMANDATA abides by Japanese law and its spirit. We make no transactions with purchasers who commit illegal acts.
1
EDX-301 v1.0
z Revision History
Date Revision Description
Apr. 16, 2012 v1.0 Initial release
z Introduction
Thank you for purchasing our product EDX-301.
EDX-301 is an evaluation board with USB interface equipped with a Xilinx FPGA
Spartan-6 series and FTDI's FT2232H.
By using the original configuration tool “BBC[EDX-301]”, no download cable or
Xilinx developing environment is needed to configure FPGA and configuration
device on the board.
* The explanations and screenshots given in this manual are based on ISE Version 13.4
2
EDX-301 v1.0
1. Specifications
Model Name EDX-301
FPGA XC6SLX16-2CSG225C
Config. Device M25P16-VMN6P (16Mbit)
On-Board Clock 50 [MHz]
External Clock Input User I/O connector (CNA-26/27, CNB-26/27)
Power Input DC 5.0 [V]
Dimensions 2.087" x 2.126" (53 x 54 [mm])
Weight 18 [g] typ.
User I/Os 56 (CNA:28, CNB:28)
User Switches 2 (Push x 1, Dip x 1bit)
User LEDs 4
7 segment LED 1
PCB 6 Layer FR-4 t1.6 [mm] Immersion gold
Power-On Reset 240 [ms] typ. (Config. reset signal)
JTAG Connector SIL 7-pin socket, 2.54 [mm] pitch
Status LEDs Power (red) x1, Done (blue) x1
Accessories
SIL7 long pin header (Mounted) x1
DIL40 pin header x 2
USB cable (Mini-B, 1.0m) x 1
RoHS Compliance YES
* There may be cases that these parts and specifications are changed.
3
EDX-301 v1.0
2. Overview
2.1. Name of Parts
Component Side
Solder Side
VIO (B)
Setting Jumpers
Oscillator (50MHz)
User I/Os (CNB)
FPGA
Config. Device
Power LED
User LED
User SW
USB bus power
Setting Jumpers
FT2232H
Setting Jumpers
USB connector
FT2232H
JTAG
FPGA
Done LED
7 segment LED
User SW
Config. Mode SW
User I/Os (CN
A
)
FT2232H
Config. Device
4
EDX-301 v1.0
2.2. Block Diagram
Hi-Speed
USB Controller
FT2232H
Spartan-6 LX
XC6SLX16-2CSG225C
JTAG
Config. Device
JTAG Buffer
DONE LED
Ext. Clock input
Ext. Clock input
5.0 V Power
5.0 V Power3.3 V output
Ch.A
Ch.B
Config.
User
Reset
Push Switch
User LEDs
Power LED (3.3V)
Power Circuit
3.3V, 1.2V
User I/Os CNA
28
4
2
2
EDX-301 Rev.C
7seg LED
DIP Switch
(Config , User)
User I/Os CNB
Oscillator
50
MHz
USB
28
2.3. 7 segment LED
Segment NET LABEL FPGAPin
a SA_O B14
b SB_O B15
c SC_O J13
d SD_O D13
e SE_O D15
f SF_O C15
g SG_O C14
DP SDP_O J11
5
EDX-301 v1.0
2.4. Clock
An oscillator, 50 MHz, is equipped as on-board clock. External clock can be input
from user I/Os.
For more details, please refer to the circuit schematics.
2.5. Power Supply
This board operates from single DC 5.0 V power supply from user I/O connectors
(CNA and CNB). The external power supply should be sufficient and stabilized.
Please do not apply over 5.0V voltage. Internally required 3.3[V] and 1.2[V] are
generated by on-board voltage regulators.
You can also use USB bus power by setting JP2.
1-3, 2-4: Short (factory setting)
Powered from user I/O connectors only
1-2, 3-4: Short
Powered by USB bus power and user I/O connectors
(Depending on FPGA design, power current may be
insufficient in USB only powering)
2.6. I/O Power Supply
FPGA banks are divided into two groups as follows.
FPGA BANK Vcco NET LABEL BANK Group Function
0 VCCO_0 VIO(B) B CNB I/O
1 VCCO_1 V33A
A
CN
A
I/O
2 VCCO_2 V33A A CNA I/O
3 VCCO_3 V33A
A
USB I/F
I/O power supply for “Bank Group A” is fixed to V33A (3.3V) and for “Bank Group
B” is supplied from JP1.
For more details, please refer to the circuit schematics.
6
EDX-301 v1.0
3-4: Short (factory setting)
Powered V33A into VIO(B)
1-2: Short
Powered V33A into VIO(B)
(Arbitrary voltage from CNB will be available from
the next product revision)
2.7. USB Controller
FTDI’s FT2232H is mounted as USB controller IC. By connecting to a PC, 2
channels (A/B) are recognized.
Chanel A is connected to user ports of the FPGA for user communication. Chanel B
is connected to pins for FPGA configuration ports.
By setting JP3, reset function and EEPROM are available.
JP3 [1-2]
Short (factory setting)
EEPROM for FT2232H is available
Open
EEPROM for FT2232H is disabled.
- FT2232H will be recognized in default setting.
(FTDI default descriptor, both A/B channels are
configured as UART mode ).
JP3 [3-4]
Short
FPGA pin is connected to FT2232H’s reset input
pin
- By setting FPGA pin to High, FT2232H will be
in its reset mode.
Open (factory setting)
FPGA pin is not connected to FT2232H’s reset pin
- To use original configuration tool, set this open
7
EDX-301 v1.0
2.8. Device Driver
To recognize USB controller, installing device driver is needed. The first time
EDX-301 is connected to a PC, installing it is required by Operation System.
The device driver is available at the support page.
2.9. DIP Switch (SW1)
SW1[2] is a user switch. X_M1 is connected to M1 pin of FPGA. It is used for the
configuration mode switching.
SW1
ASW2[2] X_M1[1] Configuration Mode
X ON Master Serial / SPI
X OFF USB / JTAG
ON: Low (0), OFF: High (1), X: Don't Care
z Master Serial / SPI mode
Use this mode to configure the FPGA by the configuration device when it is
powered on.
z USB / JTAG mode
Use this mode to configure the FPGA from a JTAG I/F or USB I/F using
“BBC[EDX-301]”. You can use this mode to avoid the FPGA being configured by
the configuration device.
8
EDX-301 v1.0
3. FPGA Configuration
3.1. Using Original Tool
By using the original configuration tool “BBC[EDX-301]”, following function is
available without download cable.
FPGA configuration
Write and Erace configuration device
“BBC[EDX-301]” is available for free from a support page.
http://www.hdl.co.jp/en/spc/XCM/edx-301/
3.2. Using JTAG Download cable
Download cable is needed to use XILINX tool (iMPACT and ChipScope). Pin
assignment is as follows.
Pin No. Signal Name Direction
1 GND I/O
2 TCK IN
3 TDO OUT
4 TMS IN
5 VCC(3.3V) OUT
6 TDI IN
7 GND I/O
9
EDX-301 v1.0
3.3. Using Configuration Device
Configuration data written in the configuration device will be configured to the
FPGA automatically when power is applied. To use this function, set configuration
mode to “Master Serial / SPI”.
Do not download inaccurate configuration data. It would damage the FPGA and
peripheral circuit.
4. Factory Setting of FT2232H EEPROM
Factory presetting is as follows.
(MPROG Version 3.5)
10
EDX-301 v1.0
5. Documentation and User Support
The following documents and other supports are available at
http://www.hdl.co.jp/en/spc/EDX/edx-301/
z Circuit Schematic
z Pin List
z Dimensional drawing
z Net List
z Original Configuration Tool “BBC[EDX-301]”
z USB Device Driver
… and more.
Spartan-6 USB-FPGA Board
EDX-301 Series
User’s Manual
Ver. 1.0 ............................................... Apr. 16, 2011
HuMANDATA LTD.
Address: 1-2-10-2F, Nakahozumi, Ibaraki
Osaka, Japan
ZIP 567-0034
Tel: 81-72-620-2002 (Japanese)
Fax: 81-72-620-2003 (Japanese/English)
URL: http://www.hdl.co.jp/en/ (Global)
http://www.hdl.co.jp/ (Japan)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Humandata EDX-301 User manual

Brand
Humandata
Model
EDX-301
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents