Humandata EDX-303-50 User manual

Brand
Humandata
Model
EDX-303-50
Type
User manual

This manual is also suitable for

HuMANDATA LTD.
Spartan-7 USB-FPGA Board
EDX-303 Rev2
User’s Manual
Ver. 2.0
Table of Contents
Revision History .............................................................................................. 1
Introduction .................................................................................................... 1
1. Specifications ..................................................................................................... 2
2. Overview ............................................................................................................ 3
2.1. Name of Parts .......................................................................................................3
2.2. Block Diagram ......................................................................................................4
2.3. Power Supply ........................................................................................................5
2.4. I/O Power Supply .................................................................................................5
2.5. Oscillator...............................................................................................................6
2.6. User Switch ..........................................................................................................6
2.7. User LED and 7-Segment LED ...........................................................................6
2.8. MRAM ...................................................................................................................6
2.9. Debug I/F ..............................................................................................................6
2.10. Setting Switch ....................................................................................................6
2.11. FT2232H Setting Jumper ..................................................................................7
3. Device Driver ..................................................................................................... 7
4. FPGA Configuration ........................................................................................... 8
4.1. Using Original Tool ..............................................................................................8
4.2. Using JTAG Download cable ...............................................................................8
4.3. Using Configuration Device ................................................................................9
5. Factory Setting of FT2232H EEPROM ............................................................... 9
6. Documentation and User Support .................................................................... 10
Precautions
Do Not
1. This product uses ordinary off-the-shelf electronic components, and is therefore inappropriate for use in
applications that require special quality or reliability and are expected to protect human lives or prevent
accidents, such as safety mechanisms in fields including space, aeronautics, medicine, and nuclear
power.
2. Do not be used underwater or in high-humidity environments.
3. Do not be used in the presence of corrosive gases, combustible gases, or other flammable gases.
4. Do not turn on power when circuit board surface is in contact with other metal.
5. Do not apply voltage higher than rated voltage.
Attention
6. This manual may be revised in the future without notice owing to improvements.
7. All efforts have been made to produce the best manual possible, but if users notice an error or other
problem, we ask that they notify us.
8. Item 7 notwithstanding, HuMANDATA cannot be held liable for the consequences arising from use of
this product.
9. HuMANDATA cannot be held liable for consequences arising from using this product in a way different
from the uses described herein, or from uses not shown herein.
10. This manual, circuit diagrams, sample circuits, and other content may not be copied, reproduced, or
distributed without permission.
11. If the product emits smoke, catches fire, or becomes unusually hot, cut the power immediately.
12. Be careful of static electricity.
13. This product may be subject to the export restrictions of Japan, the United States, or other countries.
Purchasers are responsible for properly observing export restrictions.
14. HuMANDATA firmly refuses to export (including reexporting) products to countries or regions subject to
export restrictions.
Product Warranty and Scope of Support
1. HuMANDATA guarantees that its products can be assembled as shown in published circuit diagrams and other design documents.
There may be differences between actual components or their prescribed quantities and model numbers and those shown in circuit
diagrams.
2. Except for the guarantee in item 1, above, no guarantees whatsoever are made. When assembling the product as shown in a circuit
diagram is impossible, and the problem can be solved by revising the diagram, HuMANDATA will revise the diagram. When a problem
can be solved only by replacing components or modifying the product, HuMANDATA will take back the product to replace it with a
properly functioning product.
3. If the problem is minor, HuMANDATA will sometimes describe how to make the revision or modification, and ask the customer to
solve the problem.
4. HuMANDATA will determine how to honor the warranty, as through repair, replacement, return, or other action. The customer cannot
specify what action to take.
5. FPGAs and other components used in products sometimes have characteristic defects. Returns and replacements are not possible
even if such defects are discovered, whether before or after purchase.
6. HuMANDATA shall not be obligated to inform customers about defects in the main components used in products.
7. HuMANDATA shall not be obligated to provide support for products, or to provide support for the software of other companies needed
to use HuMANDATA products.
8. Published documentation shall be limited to that published by HuMANDATA at the time of product purchase, and HuMANDATA shall
not be obligated to provide any other documentation.
9. When repairs or replacements are provided under warranty in Japan, purchaser shall pay shipping charges for shipping to
HuMANDATA, and HuMANDATA shall pay shipping charges for shipping to purchaser.
10. When shipping from outside of Japan, purchaser shall pay all expenses including shipping charges and taxes.
11. Under whatever circumstances, HuMANDATA shall provide support for its products for a maximum of one year after shipping from
factory.
12. The Warranty is not applicable and support ends in the event of fire, storm and flood damage, earthquakes, lightning strikes, and
other natural disasters, as well as conflict or other occurrences.
13. Purchaser is assumed to have read and understood all the above when purchasing a HuMANDATA product.
Limitation of Liability
1. Purchasers assume all liability associated with the use of this product.
2. HuMANDATA assumes no liability whatsoever for any direct, indirect, special, incidental, or consequential damages arising from the
use of this product, even if HuMANDATA has been advised of the possibility of such damage, whether legal or in tort.
3. At the time this product is purchased, items 1 and 2 above shall be deemed to have been confirmed by purchaser.
Trademarks and Other Considerations
1. This manual uses various companies’ trademarks in places.
2. HuMANDATA is this company’s registered trademark.
HuMANDATA’s Philosophy
1. HuMANDATA endeavors to raise product quality. We continually make detailed improvements and adjustments that are not shown
in circuit diagrams.
2. HuMANDATA actively publishes, on the Web and in other ways, information considered useful to customers. Examples would be
how to use FPGAs and how to use development tools.
3. HuMANDATA makes efforts for the long-term provision of products and for continuing their long-term support.
4. Instead of concealing small product problems and documentation errors, HuMANDATA makes them public.
5. HuMANDATA abides by Japanese law and its spirit. We make no transactions with purchasers who commit illegal acts.
1
EDX-303 v2.0
Revision History
Date
Revision
Description
Aug. 19, 2021 v2.0
Initial release for Rev2
Change: Config. Device *
* Users using previous revision need to regenerate an MCS file.
Introduction
Thank you for purchasing our product EDX-303.
EDX-303 is an evaluation board with USB interface equipped with a Xilinx FPGA
Spartan-7 series and FTDI's FT2232H.
By using the original configuration tool “BBC[EDX-303]”, no download cable or
Xilinx developing environment is needed to configure FPGA and configuration
device on the board.
2
EDX-303 v2.0
1. Specifications
Model Name
EDX-303-50 EDX-303-75 EDX-303-100
FPGA
XC7S50-1FGGA484C XC7S75-1FGGA484C XC7S100-1FGGA484C
USB2.0 Controller
FT2232H (FTDI)
Config. Device
MT25QL128ABA1EW9-0SIT (Micron, 128Mbit)
MRAM
MR2A16AMA35 (Everspin, 4Mbit)
Power Input
DC 5.0 [V]
User I/Os
56 (CNA:28, CNB:28)
On-Board Clock
50 [MHz] (External inputs are available)
User LEDs
4
7 segment LED
1
User Switches
2 (Push x 1, Dip x 1bit)
Status LED
2 (POWER, DONE)
Power-On Reset
240 [ms] typ. (Config. reset signal)
User I/O
Connectors
40-pin through-hole x2
dia. 0.9 [mm], 100[mil]/2.54 [mm] pitch
JTAG Connector
SIL 7-pin socket, 2.54 [mm] pitch
PCB
6 Layer FR-4 t1.6 [mm] Immersion gold
Dimensions
2.087" x 2.126" (53 x 54 [mm])
Weight
22 [g] typ.
Accessories
SIL7 long pin header x1
DIL40 pin header x 2
USB2.0 cable (Mini-B, 1.0m) x 1
RoHS Compliance
YES
* There may be cases that these parts and specifications are changed.
3
EDX-303 v2.0
2. Overview
2.1. Name of Parts
Component Side
Solder Side
VIO (B)
Input Jumper
Setting/User
SW
USB bus-power
Setting Jumper
JTAG
FPGA
FT2232H
7-seg LED
MRAM
Oscillator
FT2232H
Setting Jumper
Power LED
Config. Device
DONE LED
Debug I/F
User LEDs
4
EDX-303 v2.0
2.2. Block Diagram
Hi-Speed
USB Controller
FT2232H Spartan-7
X C 7 S50-1FGGA484C
X C 7 S75-1FGGA484C
X C 7 S100-1FGGA484C
JTAG
Config. Device
Buffer
DONE LED
Ext . Clock i nput
Ext . Clock i nput
5.0 V Power
5.0 V Power
3 .3 V output
Ch.A
Ch.B C o nfig.
User
R e set
User LED
Power LED (3.3V)
Power Circuit
3.3V,1.0V,1.8V
User I/Os CNA
28
4
EDX-303 Rev.B
7seg LED
Config. Mode SW
User I/Os CNB
Oscillator
USB
28
V IO(B) input
: O ption
User Switch
(DIP x1, Push x1)
M R AM (4Mbit)
2
5
EDX-303 v2.0
2.3. Power Supply
This board operates from single DC 5.0 V power supply from user I/O connectors
(CNA and CNB). The external power supply should be sufficient and stabilized.
Please do not apply over 5.0V voltage. Internally required voltages are generated
by on-board voltage regulators.
You can also use USB bus power by setting JP2.
1-3, 2-4: Short (factory setting)
Powered from user I/O connectors only
1-2, 3-4: Short
Powered by USB bus power and user I/O connectors
(Depending on FPGA design, power current may be
insufficient in USB only powering)
2.4. I/O Power Supply
FPGA banks are divided into two groups as follows.
FPGA Bank Bank Group NET Function
14
A
V33A
CNA I/O
15
A
V33A
MRAM
16
A
V33A
MRAM
34
A
V33A
USB I/F
35
B
VIO(B)
CNB I/O
I/O power of CNA, IOA, is supplied by on-board 3.3V.
I/O power of CNB, IOB, is supplied by external power
input. When JP1 is short, on-board 3.3V is supplied to VIO(B).
6
EDX-303 v2.0
2.5. Oscillator
50MHz oscillator (U1) is equipped as on-board clock. External clock
can be input from user I/O connectors.
For more detail, please refer to circuit schematics.
2.6. User Switch
A push switch (SW1) and a DIP switch (SW1[2]) are
equipped as user switch. They are pulled up, so you can
input low level signal to the FPGA when you push it.
2.7. User LED and 7-Segment LED
They are user LEDs. They are lighted by output low.
2.8. MRAM
This is a non-volatile memory for SRAM control.
For more details, please refer to the datasheet of the memory.
2.9. Debug I/F
CN2 can be used for any purpose.
They are connected through resisters to FPGA.
2.10. Setting Switch
FPGA configuration mode can be changed by this switch.
Configuration Mode
2
1
USER (ASW)
MODE
Slave Serial
X
OFF
Master SPI
X
ON
ON: Low (0), OFF: High (1), X: Don't Care
Slave Serial : JTAG or use original configuration tool
Master SPI : Use configuration memory
7
EDX-303 v2.0
2.11. FT2232H Setting Jumper
FTDI’s FT2232H is mounted as USB controller IC. By connecting to a PC, 2
channels (A/B) are recognized.
Chanel A is connected to user ports of the FPGA for user communication. Chanel B
is connected to pins for FPGA configuration ports.
By setting JP4, reset function and EEPROM are available.
JP4 [1-2]
Short (factory setting)
EEPROM for FT2232H is available
Open
EEPROM for FT2232H is disabled.
- FT2232H will be recognized in default setting. (FTDI
default descriptor, both A/B channels are configured as
UART mode ).
JP4 [3-4]
Short
FPGA pin is connected to FT2232H’s reset input pin
- By setting FPGA pin to High, FT2232H will be in its reset
mode.
Open (factory setting)
FPGA pin is not connected to FT2232H’s reset pin
- To use original configuration tool BBC[EDX-303] set this
open
3. Device Driver
To recognize USB controller, installing device driver is needed. The first time
EDX-303 is connected to a PC, installing it is required by Operation System.
The device driver is available at the support page.
8
EDX-303 v2.0
4. FPGA Configuration
4.1. Using Original Tool
By using the original configuration tool “BBC[EDX-303]”, following function is
available without download cable.
● FPGA configuration
● Write and Erace configuration device
“BBC[EDX-303]” is available for free from a support page.
When you use this tool, please set a configuration mode to Slave Serial.
4.2. Using JTAG Download cable
Download cable is needed to use XILINX tool (iMPACT and ChipScope). Pin
assignment is as follows.
Pin No.
Signal Name
Direction
1
GND
I/O
2
TCK
IN
3
TDO
OUT
4
TMS
IN
5
VCC
OUT
6
TDI
IN
7
GND
I/O
9
EDX-303 v2.0
4.3. Using Configuration Device
Configuration data written in the configuration device will be configured to the
FPGA automatically when power is applied. To use this function, set configuration
mode to “Master SPI”.
Do not download inaccurate configuration data. It would damage the FPGA and
peripheral circuit.
5. Factory Setting of FT2232H EEPROM
Factory presetting is as follows.
Item Value
Vendor ID
0F87
Product ID
1046
Bus Powered
Check
Max Bus Power
500
Manufacturer
HuMANDATA
Product Description
EDX-303 HuMANDATA
Serial Number Enabled
Disable
Port A - Hardware
245 FIFO
Port A - Driver
Virtual COM Port
Port B - Hardware
245 FIFO
Port B - Driver
D2XX Direct
10
EDX-303 v2.0
6. Documentation and User Support
The following documents and other supports are available at
https://www.hdl.co.jp/en/spc/EDX/edx-303/
Circuit Schematic
Pin List
Outline drawing
Net List
Original Configuration Tool “BBC[EDX-303]”
Device Driver
… and more.
Spartan-7 USB-FPGA Board
EDX-303 Series Rev2
User’s Manual
Ver. 2.0 ....................................... August 19, 2021
HuMANDATA LTD.
Address: 1-2-10-2 F, Nakahozumi, Ibaraki
Osaka, Japan
ZIP 567-0034
Tel: 81-72-620-2002 (Japanese)
Fax: 81-72-620-2003 (Japanese/English)
URL: https://www.hdl.co.jp/en/ (Global)
http://www.hdl.co.jp (Japan)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Humandata EDX-303-50 User manual

Brand
Humandata
Model
EDX-303-50
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers