Mr. Steam MS WALLSEAT BN Installation guide

Mr. Steam
Brand
Mr. Steam
Model
MS WALLSEAT BN
Category
Holders
Type
Installation guide
PUR 100399 4.13
•
Provide no smaller than a 2" x 6"
header in the wall for mounting.
• Drill (6) 1/8 inch holes into
the header a minimum of 1
1
⁄
2
inches
deep using the template provided.
Drill a
1
⁄
4
inch diameter hole through
any tile or wall board for screw
clearance. Brackets should be 17"
to 20" above the floor.
• Fill the holes with silicone before
securing the brackets to the wall.
• Secure wall brackets to the wall
as shown in the diagram. Note cor-
rect orientation as shown. Insure a
minimum of 1
1
⁄
2
inches
of the screws provided penetrate
the header for strength.
• Place wall bracket covers over brack-
THE MAXIMUM
WEIGHT CAPACITY OF THE SHOWER
SEAT IS 250 LBS.(113 kg) WHEN
INSTALLED IN ACCORDANCE WITH
THESE INSTRUCTIONS.
Wall and header to be
constructed as required to support a
minimum of 250 lbs. (113 kg.)
Use only
for sitting.
Not to be used for other purposes.
DO NOT install in a
location where seated user and shower
seat are close to direct steam emission.
DO NOT install the
shower seat on glass tile or any other
materials prone to damage
e
ts and secure seat assembly in place with
the hinge pins. After assembly is complet-
ed, fit caps into hinge pin holes. The seat
should raise and lower with-out binding.
• Use a level to determine if the seat folds
down flat. If required use the adjustment
screws as shown to level the seat.
IMPORTANT:
• Use only mounting hardware provided in
accordance with instructions.
• Test installation with a minimum
300 lb. (136 kg.) load prior to use.
• One person maximum capacity.
• Clean with mild soap and water.
Do not use abrasive cleaning products.
• Discontinue use if any parts appear
damaged, degraded or loose.
BOX CONTENTS:
_________________________________________________
ITEM QTY DESCRIPTION
__________________________________________
12Wall Brackets
__________________________________________
26#12, 3 inch long flat head screws
__________________________________________
32Wall Bracket Covers
__________________________________________
42Hinge Pins
__________________________________________
52Caps
__________________________________________
61Seat Assembly
__________________________________________
1 Installation Manual
__________________________________________
1 Mounting Template
__________________________________________
1 Silicone Tube
2"x 6"
Header
16" o
n
cent
er
t
ypic
al
Wall Brackets
Note correct
orientation as shown
#12, 3 inch long
flat head screw
Wall Bracket Cover
Hinge Pin
Caps
Seat Assembly
1
2
3
4
5
6
12
5
⁄8"
19
5
⁄8"
mr
.
steam
®
WALL-MOUNTED SEAT
_________________________________________________________________________
Installation Instructions Model MS Wall Seat
WARNING
!
WARNING
!
CAUTION
!
CAUTION
!
CAUTION
!
Level Adjustment Screws
Completed Assembly
Shown in seating position
mr
.
steam
®
Sussman-Automatic Corporation
®
I
[email protected]
I
www.mrsteam.com
43-20 34th Street, Long Island City, NY 11101
TEL: 1 800 76 STEAM FAX: 718 472 3256
9410 S. La Cienega Blvd. Inglewood CA 90301
TEL: 1 800 72 STEAM FAX: 310 216 2944
WARRANTY
To view or download the Mr. Steam Accessories Warranty
and register your product go to: blog.mrsteam.com/wr
  • Page 1 1

Mr. Steam MS WALLSEAT BN Installation guide

Mr. Steam
Brand
Mr. Steam
Model
MS WALLSEAT BN
Category
Holders
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents