Triad 55235-1000-1 Quick start guide

Category
Loudspeakers
Type
Quick start guide

This manual is also suitable for

TRIAD QUICK START GUIDE - IN-CEILING ROTATING SILVER/9 SAT
www.triadspeakers.com | 1-800-666-6316 | DOC-00296-B
G Size Speaker
Cutout Template
Top view
Front view Right side v(iew
OVERVIEW
When installing home theater in-ceiling speakers, sometimes the perfect
location is just not available. From ducting to pipes and light fixtures, there
are obstacles that can prevent installing the speaker where it "should" be.
The In-Ceiling Rotating Silver Sat is specifically designed to overcome
these placement challenges and optimize the home theater experience.
The In-Ceiling Rotating Silver Satellite speaker delivers the same
exceptional sound of Triad’s other Silver Satellite speakers but includes an
independently aimable woofer and tweeter that rotate to direct sound
toward the optimal listening area. To help with aiming, the Rotating Sat
has a built-in, battery-powered laser that allows an installer to see
precisely where the tweeter is aimed. This feature helps installers optimize
the sound for the optimal seating location without the assistance of
another person.
- 9-volt battery (for operating tweeter laser)
IN THE BOX
A - Enclosure (x1)
B - Grill frame (x1)
C - Grill (x1)
D - Mounting template (x1)
A
D
C
B
1
Retro installation only:
Determine desired
location for speaker
and tape or pin cutout
template into place
2
Retro installation only:
Draw an outline around
the template then
remove the template,
from ceiling. Follow the
drawn lines to cut hole
in drywall for the
speaker.
3
New construction and Retro installation: Remove the frame screws
from the speaker. Note that the retro brackets can be switched to
slide out the holes in the opposite wall.
WARRANTY
ACCESSORIES NEEDED
DIMENSIONS - IC ROTATING SILVER/9 SAT
SPECIFICATIONS - IC ROTATING SILVER/9 SAT
13
1
/
2
"
[34.3 cm]
13
1
/
2
"
[34.3 cm]
14
13
/
16
"
[37.6 cm]
frame
14
15
/
16
"
[38 cm]
grill
8
7
/
8
"
[22.5 cm]
14
15
/
16
"
[38 cm]
grill
14
13
/
16
"
[37.6 cm]
frame
ASSEMBLY
Enclosure size - in.
(H x W x D)
Enclosure size - cm
(H x W x D)
Frameless grill size - in.
NCB size
Hole cutout size - in.
Product weight (ea.)
Shipping weight (ea.)
Tweeter size (in.)
Tweeter material
13
1
/
2
x 13
1
/
2
x 8
7
/
8
34.3 x 34.3 x 22.5
14
15
/
16
x 14
15
/
16
G
13
5
/
8
x 13
5
/
8
15.95 lbs (7.25 kg)
22.6 lbs (10.27 kg)
1" nominal
Fabric dome
Woofer size (in.)
Woofer material
Recommended
amplifier power (W)
Nominal Impedance
(ohms)
Minimum Impedance
(ohms)
Sensitivity
(dB @ 2.83V, 1 m)
Frequency Response
4 π +/- 3dB
6.5" nominal
Fiber blend
25 - 125
8 ohm
5.5 ohm
86
75 Hz - 20 KHz
Triad Speakers warranty information
Limited Hardware WarrantyTriad Speakers warrants its hardware product
to be free from defects in material and workmanship during the warranty
period. If the hardware proves to be defective in material or workmanship
during the warranty period, Triad Speakers will, at its sole option, repair or
replace the product with a like product. The warranty extends only to
products purchased directly from Control4 Corporation or an Authorized
Control4 Dealer. For complete limited warranty information, including
details on purchaser legal rights as well as limited warranty exclusions, visit
http://Triadspkrs.co/warranty.
Return Merchandise Authorization (RMA) information
For Sales RMAs contact your Inside Sales Associate. Your ISA information
can be found in the My Account section of the Dealer Portal under
Control4 Contacts.
Technical Support information
Phone: 503-517-2668
Hours: 9:00 a.m. – 5:30 p.m. PST (Monday – Friday)
Email: service@triadspeakers.com
frame screw
retro
bracket
screw
Note:
For new construction, use
G-sized Triad New
Construction Brackets
(NCBs)
Copyright ©2017, Control4 Corporation. All rights reserved. Control4 and the Control4 logo are registered trademarks or
trademarks of Control4 Corporation or its subsidiaries in the United States and/or other countries. All other names and brands may
be claimed as the property of their respective owners. All specifications subject to change without notice.
retro bracket
screw
frame
screw
TRIAD QUICK START GUIDE - IN-CEILING ROTATING SILVER/9 SAT
www.triadspeakers.com | 1-800-666-6316 | DOC-00296-B
ASSEMBLY, cont. ASSEMBLY, cont. ASSEMBLY, cont.
4
LOOSELY attach the frame to the
speaker using the same screws
removed in step 3. Before putting
the speaker into the ceiling hole, be
sure to consider the orientation of
the drivers. If needed, switch the
location of the retro brackets (see
step 3) so the box can be oriented
as needed.
6
Loosen slider screws if
necessary to slide retro
brackets outward as far as
possible. Tighten screws.
7
Using rotation handles,
rotate the speaker to
point in the desired
direction. Tighten the
thumb screws when
speaker is in position.
8
To activate the aiming laser, plug a 9-volt battery into the port in front
of the tweeter. With the laser on, aim the tweeter to the desired
location using the laser beam. When finished, remove the 9-volt
battery.
9
Insert grill onto frame.
Retro bracket screws can be accessed
through holes in the frame.
5
Connect speaker wires to
binding posts, keeping
correct phase and polarity
with amp (Red+ to Red+ &
Black– to Black–). Make sure
no loose strands are shorting
between binding posts or
conductors. Tighten binding
posts Put the speaker into the
hole, making sure the woofer
is facing in roughly the
direction needed.
90°
DANGER!
VISIBLE LASER RADIATION!
AVOID DIRECT EYE EXPOSURE!
Visible laser radiation is present when battery is
attached to the terminal.
rotation handles
thumb
screws
Note: The inner portion of the speaker can rotate 90
degrees. The arrows on the rotation handles sweep
along the curved arrows on the mounting box and
indicate the limit of the rotation.
Note: With standard 1.5 inch (38mm) long 8-32 Frame screws, our speakers fit up
to 1.3 inch (33mm) thick wall or ceiling material, enough for 2 layers of
5/8 inch drywall. For thicker walls, replace with longer 8-32 screws. For example,
2 inch (51mm) 8-32 screws fit 1.8" (45.7mm) thick walls & ceilings.
Minimum wall thickness is 1/2". Even if retro brackets or frame are not used,
ALWAYS leave screws in all front bae inserts to avoid chung noises
binding posts
  • Page 1 1
  • Page 2 2

Triad 55235-1000-1 Quick start guide

Category
Loudspeakers
Type
Quick start guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI