Triad 30351-1 Quick start guide

Brand: Triad

Model: 30351-1

Type: Quick start guide

This manual is also suitable for

30341-1

Triad 30351-1 is a high-performance outdoor speaker that delivers exceptional sound quality and durability for a variety of applications.

With its weather-resistant construction, Triad 30351-1 can withstand harsh outdoor conditions, making it ideal for use in gardens, patios, pool areas, and other exposed locations. The speaker's rugged design ensures that it can endure extreme temperatures, moisture, and UV rays without compromising its performance or aesthetics.

Triad 30351-1 features a 5.25-inch woofer and a 1-inch tweeter, which work together to deliver a rich, full-range sound with deep bass and clear highs. The speaker's wide frequency response ensures that you can enjoy your music with exceptional clarity and detail, even at higher volumes.

Triad 30351-1 is a high-performance outdoor speaker that delivers exceptional sound quality and durability for a variety of applications.

www.triadspeakers.com | 1-800-666-6316

TRIAD QUICK START GUIDE CROWN CDi 2|600 ABOVE-GROUND GARDEN ARRAY AMP SETUP

Encoder

knob

Power

button

Menu button

Channel 2

Mute button

Channel 1

Mute button

Channel 2

Select button

Channel 1

Select button

Back button

Display

Channel 2

ground

(for balanced

input)

PRESET:1

IP: 192.168.0.36

NO TUNING

0.0dB

ANLG 1

ANLG 2

CH1

NO TUNING CH2

CAUTION

The ampliﬁer should not be connected to AC power until all connections are complet-

ed. High power 70/100V ampliﬁers present a serious shock hazard. Do not connect

speaker wires to the ampliﬁer until all other connections are completed.

Channel 1

ground

(for balanced

input)

1. CONFIGURE AMPLIFIER

2. NETWORK

3. SYSTEM SETTINGS

PRESET 1

IP: 192.168.0.36

From the HOME screen on the front

panel display, press the MENU

button to access the system menu.

Within the system menu, use the

Encoder knob to scroll to SYSTEM

SETTINGS. Press the encoder knob

to select SYSTEM SETTINGS.

PRESET:1

IP: 192.168.0.36

NO TUNING

0.0dB

ANLG 1 CH1

NO TUNING CH2

OVERVIEW

The following instructions is a guide for setting up the Crown CDi 2|600

ampliﬁer for a Triad Garden Array System that has a stereo source signal for

the INPUT and delivering a mono ampliﬁed OUTPUT through both of the

Crown CDi 2|600 speaker outputs. All of the Triad Garden Array Satellites will

be connected to one of the ampliﬁer outputs set for 70/100V, and the

Above-Ground Garden Array Subwoofer will be connected to the other

ampliﬁer output set for 2/4/8 ohm.

This setup will allow you to maximize the beneﬁts of both a 70/100V and

2/4/8 ohm system design. All of the satellites will be wired in parallel to a

single, 2 conductor burial wire, from the ampliﬁer channel set up for 70/100V

- allowing for up to 16 Triad Garden Array Satellites (set to the highest volume

level) to be easily installed together. The Above-Ground subwoofer will be

wired to a single, 2 conductor burial wire, from the ampliﬁer channel set up

for 2/4/8 ohm.

The Crown CDi 2|600 Amp can output both low impedance (2/4/8 ohm) and high

impedance (70/100V constant voltage) on either or both channels independently

to accommodate the Triad Garden Array (GA) Speaker System. The source Left and

Right input wires should be connected as two separate inputs (one per channel)

into the male phoenix connector, then assigned accordingly in the front panel

setup.

Using the female RCA-to-bare-wire adapter

(included with GA Subs), connect wires from

channels 1 & 2 into the Phoenix connector as

shown at left. Be sure to observe proper

polarity when connecting the wires to the

Phoenix connector.

For full front panel functionality, please refer to the Crown Ampliﬁer owner’s

manual. Most of the Triad GA system setup can be done by:

CHANNEL 1

INPUT WIRES

CHANNEL 2

INPUT WIRES

Attach wire for GA Sats and

GA Sub(s) to output connec-

tor on back of Crown amp as

shown at right.

WARNING

This QSG is ONLY intended to be used for the speciﬁc setup described in this document for the Triad Garden

Array speaker system and should be used AFTER reading the original owner’s manual for the Crown Amp and

corresponding QSGs for the Triad GA Satellite and GA Subwoofer. Ensure you are aware of all power settings

and risks before setting up your Triad Garden Array speaker system.

AMP - NAVIGATION

AMP - FRONT PANEL

AMP SETUP - NOTES

AMP SETUP - OVERVIEW

AMP CONNECTIONS - INPUT

AMP CONNECTIONS - OUTPUT

AMP GAIN SELECTION

It is recommended to use Channel 1 in 70/100V mode for the GA Sats and Channel 2

in 2/4/8 mode for the GA Sub.

Crown amp

Back of Crown amp

GA Sats

Channel 1Channel 2

Above-Ground

GA Sub

A) Rotating the Encoder Knob (counter

clockwise to scroll down, clockwise to scroll

up)

B) Pressing the Encoder Knob to select the

highlighted text/option

C) Pressing the Back button to return to the

previous screen or option

D) Pressing the Menu button to access the

main menu

CHANNEL 1

(SATS)

OUTPUT

WIRES

CHANNEL 2

(SUB)

OUTPUT

WIRES

In the AMP GAIN MODE menu, select

AMP GAIN. Via the encoder knob,

setthe AMP GAIN to +37 dBu and

select with the Encoder knob. Select

DONE when complete.

From the SYSTEM SETTINGS menu,

select AMP GAIN MODE.

1. LIGHTING / DISPLAY OPTIONS

2. SECURITY

3. DIAGNOSTICS

4. AMP GAIN MODE

SYSTEM SETTINGS

IP: 192.168.0.36

SYSTEM SETTING

IP: 192.168.0.36

AMP GAIN: +37 dBu

AMP GAIN MODE

DONE

Additional proﬁles for other ampliﬁer conﬁgurations and other

documentation can be found at: triadspkrs.co/gardenarray

When using any of today's general consumer electronics devices as the source

left and right input on this amp, for maximum performance we recommend the

following AMP GAIN MODE adjustment:

MORE DOCUMENTATION

triadspkrs.co/gardenarray

TRIAD QUICK START GUIDE CROWN CDi 2|600 ABOVE-GROUND GARDEN ARRAY AMP SETUP

in the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners. All speciﬁcations subject to change without notice.

DOC-00487-A

06-25-2019 LW

PRESET:1

IP: 192.168.0.36

CUSTOM

0.0dB

ANLG 1 CH1

CUSTOM CH2

1. CONFIGURE AMPLIFIER

2. NETWORK

3. SYSTEM SETTINGS

PRESET 1

IP: 192.168.0.36

1. GUIDED SETUP

2. LOAD PRESET

3. SAVE PRESET

4. AMP WIRING (Y, BRIDGE)

5. INPUT SOURCE

CONFIGURE AMPLIFIER

IP: 192.168.0.36

From the HOME screen on the front panel display, press the MENU

button to access the system menu. Within the system menu, use the

Encoder knob to scroll to CONFIGURE AMPLIFIER. Press the

encoder knob to select CONFIGURE AMPLIFIER.

In the EDIT DSP screen, scroll through each setting, matching the following

screens. Turn o all settings not shown.

Back on the HOME screen, you can now set the relative volume (balance)

between Channel 1 (GA Sats) & Channel 2 (GA Sub). 0.0dB should be the

default values shown. This adjustment allows you to reduce the volume of

one channel independently from the other.

As an example, let’s say we have just completed all the other set-up

adjustments described in this guide and as we are listening to the ﬁnished

set-up. We ﬁnd that the GA Sub is too loud in comparison to the GA Sats

and we need to reduce the GA Sub Volume. To reduce the volume on just

the GA Sub (Channel 2) by -3.0dB, following these steps:

A) press the CHANNEL 2 SELECT button and B) turn the Encoder Knob to

set the relative volume between the GA Sats (Channel 1) and the GA Sub

(Channel 2). Turn the Encoder Knob until -3.0dB is shown in the display in

relation to channel 2. When completed making the volume adjustment,

Press the CHANNEL 2 SELECT button again to complete this step.

Turning the encoder knob for volume after setting their relative volume

will scale them proportionally together.

Initial screen

In the AMP WIRING SETUP, verify

the Y 1+2 box is NOT checked so

inputs will not be combined. The

inputs will be combined in a later

step. This ensures maximum

output of the amp. Leave the

BRIDGE box unchecked, highlight

the NEXT button and select it.

On the INPUT SOURCE screen,

ensure ANLG 1+2 is in the box at

top left and ANLG 1+2 is in the box

directly below, then select NEXT.

INPUT SOURCE

IP: 192.168.0.36

NO TUNING

ANLG 1+2

NO TUNING CH2

CH1

OUTPUT MODE SETUP

IP: 192.168.0.36

NO TUNING 70V

NO TUNING 2/4/8

ANLG 1+2

From the CONFIGURE AMPLIFIER

menu, select GUIDED SETUP.

AMP SETUP (cont.)

Within the OUTPUT MODE

SETUP screen, scroll and modify

values until the top output

channel reads 70V (for the GA

Sats) and the bottom channel

reads, 2/4/8 (for the GA 10

Sub). Select NEXT.

AMP SETUP

AMP SETUP (cont.)

TIPS AND TRICKS

DEVICE PRESETS—The Crown CDi 2|600 allows you to save dierent amp

conﬁgurations into memory for future quick recall. Settings that can be stored to

Device Presets include; DSP Settings, channel assignments, gains, levels, mutes,

source assignments, and output modes.

Please see page 53 of the full Crown CDi 2|600 Owner's Manual for full details on

saving and recalling a preset.

REMOTE TURN-ON—On the back panel of the Crown CDi 2|600 is an 8 pin GPIO

(General Purpose In/Out) Control / AUX Port. The AUX Port can be used for basic

monitoring of the ampliﬁer and for remote standby (sleep) depending on the

control system that you are connecting the Crown CDi 2|600.

Please see page 59 of the full Crown CDi 2|600 Owner's Manual for full details on

pin out conﬁguration of the GPIO connector to support remote turn-on.

SECURITY/FRONT PANEL LOCKOUT—The Crown CDi 2|600 allows the front panel

functionality to be locked out to prevent unauthorized tampering of the ampliﬁer's

settings.

Please see page 56 of the full Crown CDi 2|600 Owner's Manual for full details on

enabling and disabling the Front Panel Lockout function.

AMP WIRING SETUP

IP: 192.168.0.36

Y 1+2

NO TUNING

BRIDGE

1 + 2

CH1 CROSSOVER

EDIT DSP - CH1

HIGH PASS

IP: 192.168.0.36

HP ENABLE:

HP TYPE:

HP FREQ:

LP ENABLE:

LP TYPE:

LP FREQ:

GAIN:

POLARITY:

L-R 24

120Hz

Off

L-R 24

20kHz

0.0dB

Normal

CROSSOVER

CH1 OUTPUT PEQ - Band 1

EDIT DSP - CH1

IP: 192.168.0.36

ENABLE:

BAND:

TYPE:

FREQ:

GAIN:

Band 1

Bell

320Hz

6.0dB

0.704

OUTPUT PEQ

CH2 CROSSOVER

EDIT DSP - CH2

BAND PASS

IP: 192.168.0.36

HP ENABLE:

HP TYPE:

HP FREQ:

LP ENABLE:

LP TYPE:

LP FREQ:

GAIN:

POLARITY:

L-R 24

26Hz

L-R 24

200Hz

0.0dB

Normal

CROSSOVER

CH2 OUTPUT PEQ - Band 1

EDIT DSP - CH2

IP: 192.168.0.36

ENABLE:

BAND:

TYPE:

FREQ:

GAIN:

Band 1

Bell

38Hz

5dB

OUTPUT PEQ

CH2 LIMITER

EDIT DSP - CH2

IP: 192.168.0.36

ENABLE:

RMS VOLT:

THERMAL VOLT:

THERMAL RESP:

30.00

50.00

10.00

LIMITER

ANLG 1+2

DONE

EDIT DSP

IP: 192.168.0.36

DELAY

INPUT OUTPUT

PEQ PEQ DELAY LIMITXOVER

CH1

ANLG 1+2

CH2

A B

C D E

EDIT DSP

IP: 192.168.0.36

ANLG 1+2

DONE

DELAY

INPUT OUTPUT

PEQ PEQ DELAY LIMITXOVER

CH1

ANLG 1+2

CH2

ANLG 1+2

Final screen, select DONE

CH1 OUTPUT PEQ - Band 2

EDIT DSP - CH1

IP: 192.168.0.36

ENABLE:

BAND:

TYPE:

FREQ:

GAIN:

Band 2

Bell

1.4kHz

-7.0dB

OUTPUT PEQ

CH1 OUTPUT PEQ - Band 3

EDIT DSP - CH1

IP: 192.168.0.36

ENABLE:

BAND:

TYPE:

FREQ:

GAIN:

Band 3

Bell

4kHz

2.0dB

OUTPUT PEQ

CH1 OUTPUT PEQ - Band 4

EDIT DSP - CH1

IP: 192.168.0.36

ENABLE:

BAND:

TYPE:

FREQ:

GAIN:

Band 4

Bell

13kHz

-8.0dB

OUTPUT PEQ

CH2 OUTPUT PEQ - Band 2

EDIT DSP - CH2

IP: 192.168.0.36

ENABLE:

BAND:

TYPE:

FREQ:

GAIN:

Band 2

Bell

75Hz

-3dB

OUTPUT PEQ

CH2 OUTPUT PEQ - Band 3

EDIT DSP - CH2

IP: 192.168.0.36

ENABLE:

BAND:

TYPE:

FREQ:

GAIN:

Band 3

Bell

400Hz

-6dB

OUTPUT PEQ

For additional DSP conﬁgurations including 8 ohm sat settings and Underground sub settings,

see triadspkrs.co/gardenarray

Triad 30351-1 Quick start guide

Brand: Triad

Model: 30351-1

Type: Quick start guide

This manual is also suitable for

30341-1

Triad 30351-1 is a high-performance outdoor speaker that delivers exceptional sound quality and durability for a variety of applications.

Download PDF

report

Triad 30351-1 Quick start guide

This manual is also suitable for

Triad 30351-1 Quick start guide

Related papers

Other documents