LXE MX1-IS User manual

Brand: LXE

Model: MX1-IS

Type: User manual

This manual is also suitable for

MX1 Intrinsically Safe

MX1 Intrinsically Safe User’s Guide

I-Safe rating is voided if the MX1-IS device is opened or modified in the field. Removing

any leather covering in an I-Safe environment also voids the I-Safe rating.

E-EQ-MX1ISOGWW-J

Language: English

Notices

The user is strongly encouraged to read Appendix B, "Regulatory Notices and Safety

Information." Important safety cautions, warnings and regulatory information is

contained in Appendix B.

Notices:

LXE Inc. reserves the right to make improvements or changes in the products described in this manual at any time

without notice. While reasonable efforts have been made in the preparation of this document to assure its accuracy,

LXE assumes no liability resulting from any errors or omissions in this document, or from the use of the information

contained herein. Further, LXE Incorporated, reserves the right to revise this publication and to make changes to it

from time to time without any obligation to notify any person or organization of such revision or changes.

This manual is copyrighted. All rights are reserved. This document may not, in whole or in part, be copied,

photocopied, reproduced, translated or reduced to any electronic medium or machine-readable form without prior

consent, in writing, from LXE Inc.

125 Technology Parkway, Norcross, GA 30092 U.S.A. (770) 447-4224

LXE® is a registered trademark of LXE Inc. All other brand or product names are trademarks or registered

trademarks of their respective companies or organizations. When this manual is in PDF format: “Acrobat ® Reader

Acrobat logo are trademarks of Adobe Systems Incorporated.” Applies.

NOTICE: Changes to this document require LXE Regulatory Engineering Approval.

Important: This symbol is placed on the product to remind users to dispose of Waste Electrical and

Electronic Equipment (WEEE) appropriately, per Directive 2002-96-EC. In most areas, this product

can be recycled, reclaimed and re-used when properly discarded. Do not discard labeled units with

trash. For information about proper disposal, contact LXE through your local sales representative, or

visit www lxe com.

Revision Notice

Important Safety Instruction and

Warnings

Added MX1ISA382BATT and note (Battery part number is

country specific. Check with your LXE Representative when

ordering replacement batteries for the MX1-IS.)

J Accessories

Added MX1ISA382BATT and note (Battery part number is

country specific. Check with your LXE Representative when

ordering replacement batteries for the MX1-IS.)

Revision Letter I not used.

E-EQ-MX1ISOGWW-J MX1 I-Safe User’s Guide

Table of Contents

FEATURES OF THE MX1 INTRINSICALLY SAFE HAND HELD COMPUTER 1

Introduction ............................................................................................................... 1

Important Safety Instruction and Warnings............................................................ 2

Scanner Warnings and Labels................................................................................. 4

MX1 I-Safe Components........................................................................................... 5

The Protective Case ..................................................................................................................5

The Pistol Grip Handle .............................................................................................................5

Display ....................................................................................................................... 6

Icons..........................................................................................................................................6

Cleaning the Glass Display/Scanner Aperture .........................................................................6

Display Backlight .....................................................................................................................7

Display Backlight Timer ........................................................................................................7

Panning .....................................................................................................................................7

Intrinsically Safe Endcap.......................................................................................... 8

Scanner Endcap ........................................................................................................................8

Scanner Endcap Indicators .......................................................................................................8

Keypad Controls ....................................................................................................... 9

Full Alpha-Numeric (60 Key) ..................................................................................................9

Numeric-Alpha (41 Key)........................................................................................................10

Scan Key Function..................................................................................................................10

Enter Key Function.................................................................................................................10

Field Exit Key Function (IBM 5250 Only) ............................................................................10

Arrow / Cursor Key Function.................................................................................................10

2nd Key Function ...................................................................................................................11

CTRL Key Function ...............................................................................................................

ALT Key Function..................................................................................................................11

SHFT Key Function................................................................................................................11

SPC Key Function ..................................................................................................................

Mode Key Functions...............................................................................................................

CAPS Mode..........................................................................................................................12

Alpha to Numeric Toggle with A / #....................................................................................12

Keypress Sequences................................................................................................................12

Reset Key Sequence ...............................................................................................................

Power Button Functions......................................................................................... 13

Off Timer and Critical Suspend Mode ...................................................................................

Power Status and the Status LED ...........................................................................................

Power Management and the Keypad....................................................................................

Getting Help.............................................................................................................

Manuals...................................................................................................................................15

ii Table of Contents

MX1 I-Safe User’s Guide E-EQ-MX1ISOGWW-J

Accessories .............................................................................................................................15

OPERATION 17

Insert I-Safe Main Battery Pack.............................................................................. 17

Power On and Off.................................................................................................... 18

Turn On the MX1-IS ..............................................................................................................18

Turn Off the MX1-IS..............................................................................................................18

Adjust Display and Volume.................................................................................... 19

Set The Display Contrast ........................................................................................................19

Full Alpha-Numeric .............................................................................................................19

Numeric-Alpha Keypad .......................................................................................................19

Set The Beeper Volume..........................................................................................................19

Full Alpha-Numeric .............................................................................................................19

Numeric-Alpha Keypad .......................................................................................................19

Enter Data ................................................................................................................ 20

Keypad Entry ..........................................................................................................................20

Scanner Entry..........................................................................................................................20

MX1-IS Environmental Specifications................................................................... 21

I-Safe Main Battery.................................................................................................. 21

Battery Pack............................................................................................................................21

Critical Suspend State.............................................................................................................21

Battery Charger....................................................................................................... 22

Optional LXE MULTI-charger...............................................................................................22

APPENDIX A KEY MAPS 23

Full Alpha-Numeric Key Map (60 Key) .................................................................. 23

Full Alpha-Numeric Key Map 101-Key Equivalencies for DOS Units.................................24

IBM 3270 and TN3270 Terminal Emulator Keypad..............................................................29

IBM 5250 and TN5250 Terminal Emulator Keypad..............................................................

Numeric-Alpha Key Map (41 Key).......................................................................... 31

Numeric-Alpha Key Map 101-Key Equivalencies for Batch Units .......................................

PPENDIX B REGULATORY NOTICES AND SAFETY INFORMATION 37

Approvals ................................................................................................................ 38

Revision History...................................................................................................... 45

INDEX 47

Table of Contents iii

E-EQ-MX1ISOGWW-J MX1 I-Safe User’s Guide

Illustrations

Figure 1 The MX1-IS Hand Held Computer........................................................................................................1

Figure 2 Scanner Module, Top.............................................................................................................................4

Figure 3 Other Equipment Labeling.....................................................................................................................4

Figure 4 Caution Labels - Scanner Module, Back ...............................................................................................4

Figure 5 Caution Labels - Scanner.......................................................................................................................4

Figure 6 MX1-IS Components.............................................................................................................................5

Figure 7 MX1-IS Display ....................................................................................................................................6

Figure 8 Scanner Endcap .....................................................................................................................................8

Figure 9 Scanner Endcap LEDs and Beeper ........................................................................................................8

Figure 10 The Alpha-Numeric Keypads ..............................................................................................................9

Figure 11 The Numeric-Alpha Keypad..............................................................................................................10

Figure 12 Location of the Power (PWR) Button................................................................................................13

Figure 13 Power Status and the Status LED ......................................................................................................14

Figure 14 Open Battery Door.............................................................................................................................17

Figure 15 Location of the Power Button............................................................................................................18

Figure 16 Scan Beam .........................................................................................................................................20

Figure 17 MX1-IS Battery and Charging Cup ...................................................................................................22

Figure 18 Full Alpha-Numeric Keypad .............................................................................................................23

Figure 19 IBM 3270 Specific Keypad ...............................................................................................................29

Figure 20 IBM 5250 Specific Keypad ...............................................................................................................30

Figure 21 Numeric-Alpha Keypad.....................................................................................................................31

iv Table of Contents

MX1 I-Safe User’s Guide E-EQ-MX1ISOGWW-J

E-EQ-MX1ISOGWW-J MX1 I-Safe User’s Guide

Features of the MX1 Intrinsically Safe Hand Held Computer

Introduction

This document provides safety instructions, warnings, and regulatory compliance information

important for the safe operation and use of the LXE® model MX1 Intrinsically Safe (MX1-IS)

Hand Held Computer within hazardous environments.

Figure 1 The MX1-IS Hand Held Computer

Note: Although there is an IR window and four battery charger connectors on the bottom of the

MX1-IS device, these capabilities are non-powered and non-functional. There is no

backup battery in the MX1-IS device.

The MX1-IS is a rugged, portable, hand-held computer capable of mobile wireless data

communications. The MX1-IS can transmit information using either a 900 MHz or 2.4 GHz radio.

The MX1-IS has a mandatory protective leather case and pistol grip handle. The leather protective

case allows the scanner aperture, scanner status indicators, system status indicator, display, keypad

and pistol grip trigger to be accessible to the user. The Main Battery Pack can be removed and

replaced without removing the leather case or the pistol grip handle.

The MX1-IS is a DOS compatible computer designed to run software applications such as LXE’s

Terminal Emulator applications (ANSI Plus, LDS Plus, DOS 5250, DOS 3270, TN3270 and

TN5250).

The heart of the MX1-IS is an Intel® 486 processor that is PC compatible. It features a graphics

screen with electroluminescent backlight. The keypad is constructed of a phosphorescent material

that needs no backlighting. The high-impact plastic case is designed to withstand multiple drops in

an industrial environment. The MX1-IS can be stored in a non-powered docking station on a desk

or a vehicle.

Note: The 900MHz radio is obsolete. Terminal emulators requiring 900MHz radios are

obsolete as of June 2005 (e.g. 3270 DOS TE, 5250 DOS TE).

2 Important Safety Instruction and Warnings

MX1 I-Safe User’s Guide E-EQ-MX1ISOGWW-J

SAVE THESE INSTRUCTIONS

Important Safety Instruction and Warnings

It is necessary to take special precautions as detailed below to avoid the introduction of fire or explosion

hazards when operating the MX1-IS device within a hazardous environment. Please read this page

carefully and make sure you fully understand these instructions.

DO NOT USE THIS UNIT IN CLASSIFIED AREAS UNSUITABLE FOR ITS SAFETY

RATINGS.

US Approval

Per the Class / Division Classification System, this unit is

rated for safe use in the following classified locations:

Class I, II, III

Division 1 & 2

Groups C, D, E, F, G

135° C (T4)

amb

-20°C to +40° C (-4°F to 104°F)

US Approval

Per the Class / Zones Classification System, this unit is rated

for safe use in the following classified locations:

Class I

Zones 0

AEx ia IIB T4

135°C (T4)

-20°C <

< +40°C

European Approval EEx ia IIB T4

-20°C <

< +40°C

Australian Approval Ex ia IIB T4

-20°C <

< +40°C

The following symbol is used to identify and warn against specific hazards, and for accident prevention

purposes:

Safety Alert Symbol with Keyword Definition and Meaning

Warning

Keyword that indicates a potentially hazardous

situation which, if not avoided, could result in

death or serious injury.

Warning:

1. The MX1-IS device is provided with a leather, impact-resistant case LXE part no.

MX1ISA406CASE. Operation of the MX1-IS device in a hazardous location environment

with the leather case removed voids intrinsic safety approval and is prohibited. If the case is

damaged, replace it before using the MX1-IS again.

2. To prevent static charge accumulation on the surface of the device, clean with a damp cloth

only. Wiping it with a dry cloth, or against clothing, may cause a buildup of static electricity.

Always use the leather case.

3. Discontinue use if the MX1-IS device is damaged or altered. Use of damaged or altered

equipment will void the intrinsic safety of the MX1-IS computer.

4. Substitution of components may impair intrinsic safety. Please return the MX1-IS device to

LXE for proper equipment repair or replacement. This device is not user or field-serviceable.

Important Safety Instruction and Warnings 3

E-EQ-MX1ISOGWW-J MX1 I-Safe User’s Guide

5. Do not substitute batteries. The MX1-IS device is only intrinsically safe when used with the

approved LXE Main Battery Pack part no. MX1ISA381BATT / MX1ISA382BATT. Use of

any other battery pack voids the intrinsic safety approval of the MX1-IS device and is strictly

prohibited.

6. The Main Battery Pack must be in place for proper electrical polarity. Discontinue use if the

battery pack is damaged or altered. Use of a damaged or altered Main Battery Pack voids the

intrinsic safety approval of the MX1-IS device and is strictly prohibited.

7. Do not charge or recharge Main Battery Packs within a hazardous environment. The LXE

MULTI-chargers LXE part no. MX1ISA378CHGR3WW specifically for use with the MX1-IS

Main Battery Pack, are not intrinsically safe or approved for use in hazardous environments.

8. The MX1-IS device is provided with intrinsic safety warning labels. Do not alter or remove

these labels. Do not cover or obstruct these labels from view.

9. The MX1-IS battery, MX1ISA381BATT / MX1ISA382BATT, may be exchanged with a fully

charged battery in a hazardous location. The MX1-IS must be powered off before opening the

Battery Door.

Failure to comply with these instructions may result in death or

serious injury to persons due to potential increased risk of fire and

explosion when used in a hazardous location.

Important – LXE manufactures a device physically similar to the MX1

Intrinsically Safe Hand Held Computer (MX1-IS). Do not place MX1-IS

Main Battery Packs in any battery charging device not specifically

designed for the MX1-IS. Also, the MX1-IS device is not compatible

with the LXE MX1 device or the MX1 Main Battery Packs.

MX1-IS battery part number is country specific. Check with your LXE

Representative when ordering replacement batteries for the MX1-IS.

SAVE THESE INSTRUCTIONS

4 Scanner Warnings and Labels

MX1 I-Safe User’s Guide E-EQ-MX1ISOGWW-J

Scanner Warnings and Labels

• Do not look into the laser’s lens.

• Do not stare directly into the laser beam.

• Do not remove the laser caution labels from the MX1-IS device.

• Do not connect the laser barcode module to any other device. The laser barcode module is

certified for use with the MX1-IS device only.

Caution:

Laser radiation when open. Please read the caution labels.

Use of controls, adjustments or performance of procedures other than those specified

herein may result in hazardous radiation exposure.

1 - Laser Scanner Aperture

MANUFACTURED: SEPTEMBER 2006

LXE 6726 TRANSCEIVER 480631 - 5010

FCC ID: KDZLXE6726M

CANADA: 1995391205A

II 2 G D EEx ia IIB T4, IP65 Nemko 03ATEX1346

IS CL I, II, III, DIV 1, 2, GP C, D, E, F, G, T4

IS CLASS I, ZONE 0, AEx ia IIB T4

Ex ia IIB T4 AUS Ex 03.3897X

APPROVED

NORCROSS, GA 30092

MADE IN U.S.A.

TERMINAL S/N: MX1-IS06383353

MODEL #: MX1-IS

SPC: MX1ISAFE

Figure 2 Scanner Module, Top

Figure 3 Other Equipment Labeling

2 - CDRH or IEC 825 Label

Figure 4 Caution Labels - Scanner Module, Back Figure 5 Caution Labels - Scanner

Note: The “MX1 I-Safe Reference Guide” contains MX1-IS technical information and

advanced functions. (located on the LXE Manuals CD and on the LXE ServicePass

website).

MX1 I-Safe Components 5

E-EQ-MX1ISOGWW-J MX1 I-Safe User’s Guide

MX1 I-Safe Components

1. Endcap

2. Scan

Indicators

3. Beeper

4. Status

Indicator

5. Display

6. Scan

Buttons

7. Keypad

8. Power

Button

1. Scan

Aperture

2. Warning

Label

3. Safety

Ratings Label

4. Handle

Contacts

5. Main Battery

Pack Cover

Latch

MX1-IS Front

MX1-IS Back

Figure 6 MX1-IS Components

The Protective Case

The protective case is constructed of leather. The case must be used at all times to prevent static

buildup in a hazardous environment.

The Pistol Grip Handle

The handle enables the user of the MX1-IS to hold the unit while pointing and activating the laser

scanner with one hand. Pulling the trigger activates the scanner and functions the same as the

SCAN key on the keypad. With the handle installed the SCAN key on the keypad remains active.

The trigger duplicates the operation.

The handle is built of a durable and flexible plastic that may detach from the MX1-IS if the unit is

dropped. The handle won’t detach completely, because the leather case is covering it.

Although the handle is removable, it must always be installed with it's leather grip to prevent static

buildup in hazardous environments.

6 Display

MX1 I-Safe User’s Guide E-EQ-MX1ISOGWW-J

Display

Figure 7 MX1-IS Display

The MX1-IS display is a transflective monochrome backlit LCD unit capable of supporting gray

scales.

Icons

Across the top of the display are icons that provide visual cues to current computer operation.

Icon When highlighted ...

CAPS CAPS is on when upper case letters are selected. To enable or disable CAPS, press

2nd, then SHIFT, then the left arrow key.

2nd

The 2nd functions of the keypad are active.

Low Main Battery indicator. This indicates that the Main Battery Pack charge is

low and the battery should be replaced.

AAA This is the backup battery indicator for LXE MX1-IS devices. The MX1-IS device

does not have a backup battery. This indicator can be ignored.

Alpha Numeric-Alpha keypad only. The A/# key is in Alphabetic mode. Operation in

Numeric Mode is indicated by the absence of the Alpha icon. Toggling between

Alphabetic and Numeric modes is accomplished by pressing the A/# key.

Ctrl

The Control functions of the keypad are active.

Alt

The Alternate functions of the keypad are active.

Shift

Shift keys output between upper and lower case letters.

Cleaning the Glass Display/Scanner Aperture

Note: Do not perform the following steps in a hazardous environment.

Keep fingers and rough or sharp objects away from the scan aperture and display. If the glass

becomes soiled or smudged, clean only with a standard household cleaner such as Windex(R)

without vinegar or use Isopropyl Alcohol. Do not use paper towels or harsh-chemical-based

cleaning fluids since they may result in damage to the glass surface. Use a clean, damp, lint-free

cloth. Do not scrub optical surfaces. If possible, clean only those areas which are soiled.

Lint/particulates can be removed with clean, filtered canned air.

Display 7

E-EQ-MX1ISOGWW-J MX1 I-Safe User’s Guide

Display Backlight

A display backlighting feature is available and depending upon programming, will operate in one

of three ways:

• Backlighting Off. This is the most efficient way to operate the computer with battery

power.

• Backlighting On For A Short Time. This will provide display backlighting for a

predetermined amount of time. Use of this feature will result in reduced battery life.

• Backlighting On Whenever The Unit Is On. This provides full time backlighting to the

display whenever the unit is turned on. It greatly reduces the expected battery life.

Display Backlight Timer

When the Display Backlight Timer expires the display backlight is turned off. The default value

for this parameter is 3 seconds. The value can be adjusted using the BIOS Setup. Refer to the

“MX1 I-Safe Reference Guide.”

Any of the following will wake the display and display backlight:

• Display update by host or currently running application on the MX1-IS

• Trigger

• Any key on the keypad

When the display wakes up, the Display Backlight Timer will begin the countdown again. When

any of the above events occur prior to the timer expiring, the timer starts the countdown again.

Panning

The MX1-IS display can be panned around using keypress sequences so the user can view an

entire virtual 640 x 480 pixel screen. Initially, the 20 columns and 20 rows in the top left corner of

a virtual screen are displayed.

Full Alpha-Numeric Keypad (60 keys)

Up, Down, Left and Right 2

key then the arrow key

Home 2

and Shift keys and letter I key

Numeric-Alpha Keypad (41 keys)

Up, Down, Left and Right 2

and Ctrl and the arrow key

Home 2

and Ctrl and the Enter key

When the Home key sequence is pressed, the cursor moves to the top left hand corner of the

virtual screen display.

When the initial 20 row x 20 column portion of the virtual screen is displayed:

• and the Pan Right key sequence is pressed, columns 10 through 30 are shown on the

display.

• and the Pan Down key sequence is pressed, rows 5 through 25 are shown on the display.

Please refer to the “MX1 I-Safe Reference Guide” for technical information about the Panning

function.

8 Intrinsically Safe Endcap

MX1 I-Safe User’s Guide E-EQ-MX1ISOGWW-J

Intrinsically Safe Endcap

The MX1-IS can be configured with several different laser scan-range endcaps. Endcaps are

mounted on the top of the computer case and contain the beeper. The endcap port is designated as

COM 1.

Read all cautions, warnings and labels before using the scanner.

Important

See also section titled “Scanner Warnings and Labels.”

Scanner Endcap

Several scanner endcaps are available with the MX1-IS. These consist of a High Performance,

Long Range, and Advanced Long Range scanner endcaps. Externally they appear identical with

the same indicators. Barcode Scanner operation varies depending upon the application but, once

enabled, the scanners are activated by pressing either the “Scan” button on the keypad or pulling

the trigger on the handle.

Figure 8 Scanner Endcap

The range of a scanner is dependent upon many outside influences including size of the barcode,

quality of the barcode printing, material the barcode is printed on, and angle of the scanner endcap

relative to the barcode label. Any of these factors may result in having to re-scan the label from a

different distance or angle.

Scanner Endcap Indicators

Read all cautions, warnings and labels before using the scanner endcaps.

1 – Laser On Indicator

2 – Beeper

3 – Good Read Indicator

Figure 9 Scanner Endcap LEDs and Beeper

The left LED (1 - Laser On Indicator) on the top of the laser barcode endcap illuminates red,

indicating laser emission when the laser beam is being emitted. Following a good read, the right

LED (3 - Good Read Indicator) flashes green, indicating a successful scan. Beeps may be heard

after a good read, depending on the application running on the MX1-IS.

The laser automatically turns off after a successful read and is ready to scan again when the Scan

key (or the trigger) is pressed.

Keypad Controls 9

E-EQ-MX1ISOGWW-J MX1 I-Safe User’s Guide

Keypad Controls

There are two keypads available for the MX1-IS. All keypads are phosphorescent. A

phosphorescent keypad does not use a keypad backlight but glows in dim/dark areas after

exposure to a light source.

All keypads are installed and configured by LXE. Full alpha-numeric (60 key) keypads are

available that are directly suited to ANSI, IBM 3270 and IBM 5250 host computer systems.

The keymaps (keypress sequences) are located in “Appendix A - Key Maps.”

Full Alpha-Numeric (60 Key)

Full Alpha-Numeric IBM 3270 Alpha-Numeric IBM 5250 Alpha-Numeric

Figure 10 The Alpha-Numeric Keypads

Note: The 900MHz radio is obsolete. Terminal emulators requiring 900MHz radios are

obsolete as of June 2005 (e.g. 3270 DOS TE, 5250 DOS TE).

10 Keypad Controls

MX1 I-Safe User’s Guide E-EQ-MX1ISOGWW-J

Numeric-Alpha (41 Key)

Figure 11 The Numeric-Alpha Keypad

Please refer to Appendix A “Key Maps” for keypress sequences.

Scan Key Function

The Scan key activates the scanner when a scanner endcap is installed and either of the

two Scan buttons is pressed. This feature accommodates both left and right handed users

comfortably.

Enter Key Function

The Enter key is used to confirm a forms entry or to transmit information. How it is used

is determined by the application running on the computer. There are two Enter keys on all keypads

except the IBM 5250 Full Alpha-Numeric keypad which has one Enter key.

Field Exit Key Function (IBM 5250 Only)

The Field Exit key is used to exit an input field. If the field is an Auto Enter field, the

auto transmit function is activated. This key is present on the IBM 5250 specific keypad only.

Arrow / Cursor Key Function

The arrow keys (also called the cursor movement keys) are used to scroll through the

active display or to move the cursor around the screen.

Keypad Controls 11

E-EQ-MX1ISOGWW-J MX1 I-Safe User’s Guide

2nd Key Function

The 2nd key is colored yellow and is used to activate the 2

functions of the keypad.

Printed above many keys are yellow characters that represent the 2

function of that key. Using

the 2

key activates the second key function. Note that the 2

key only stays active for one

keystroke. Each time you need to use the 2

function you must press the 2

key. To cancel a 2

function before pressing another key, press the 2

key again. When the 2

function is active, the

icon stays on the screen.

For example:

• Full Alpha-Numeric : 2nd plus the I key initiates INSERT mode.

• Numeric-Alpha : 2

plus the SPC key initiates ALT mode.

CTRL Key Function

The CTRL key enables the control functions of the keypad. This function is similar to a

regular keyboard’s Control key. Note that the Ctrl key only stays active for one keystroke. Each

time you need to use a Ctrl function, you need to press the Ctrl key before pressing the function

key. When the Ctrl function is active, the Ctrl icon stays on the screen.

ALT Key Function

Note: Full alpha-numeric keypad only.

The ALT key enables the alternate functions of the keypad. This function is similar to a

regular keyboard’s Alt key. Note that the Alt key only stays active for one keystroke. Each time

you need to use an alternate function, you need to press the Alt key before pressing the function

key. When the Alt function is active, the Alt icon stays on the screen.

SHFT Key Function

The Shft key enables the shifted functions of the keypad. This function is similar to a

regular keyboard’s Shift key. Note that the Shift key only stays active for one keystroke. Each

time you need to use a Shifted function, you need to press the Shft key before pressing the

function key. When the Shft function is active, the Shft icon stays on the screen.

When the Shft key is pressed the next key is determined by the major key legends, i.e., the alpha

keys display lower case letters when CAPS is On and function keys enable the shifted function

key.

SPC Key Function

Note: Numeric-alpha keypad only. SPC is a 2nd function on the full alpha-numeric keypad.

The Spc key adds a space to the line of data on the display. This function is similar to a

regular keyboard’s Spacebar. Note that the SPC key only stays active for one keystroke.

12 Keypad Controls

MX1 I-Safe User’s Guide E-EQ-MX1ISOGWW-J

Mode Key Functions

CAPS Mode

This function is similar to a regular keyboard’s CapsLock key. Note that the CapsLock mode stays

active until the CapsLock key sequence is pressed again. Each time you need to use a Caps

function, you need to press the Caps key sequence first. To cancel a CapsLock function press the

Caps key sequence again. When the CapsLock mode is active, the Caps icon stays on the screen.

Caps mode on both keypads is accessed through the key sequence 2

plus Shft plus Left arrow.

Alpha to Numeric Toggle with A / #

Note: Numeric-alpha keypad only.

When the keypad is in Alpha mode, the Alpha icon stays on the screen. When the Alpha

icon is not displayed, the keypad is in numeric mode. Note that the Alpha or Numeric mode stays

active until the A / # key is pressed again.. To toggle the A / # mode press the A / # key again.

The exception to this rule

-- when the keypad is in numeric mode and you want to type one alpha

character within a sequence of numbers, pressing 2

plus Ctrl and then the A / # key will toggle

the keypad to alpha mode for one character – the next key pressed. Then the keypad returns to

numeric mode. Likewise for toggling alpha to numeric for one key only.

Keypress Sequences

See Appendix A for key maps for the alphanumeric and numeric-alpha keypads. MX1-IS specific

key maps for the 3270 and 5250 keypads are contained in the 3270 and 5250 DOS Terminal

Emulation Reference Guides.

Reset Key Sequence

Reset Key Sequence is Ctrl + Alt + Del.

• Del is a 2nd function on the full alpha-numeric keypad.

• Alt is a 2nd function on the numeric-alpha keypad.

The Reset Key sequence can be disabled in the BIOS Setup. See the “MX1 I-Safe Reference

Guide.”

Power Button Functions 13

E-EQ-MX1ISOGWW-J MX1 I-Safe User’s Guide

Power Button Functions

Figure 12 Location of the Power (PWR) Button

Note: The IR window and four battery charger connectors are present, but they are non-

powered and non-functional. The unit does not have a backup battery.

The Power button is used to turn the MX1-IS on and off and force it into the Suspend state. The

button will beep when pressed and beep again every second while it is held down.

How To

• Turn the MX1-IS off

Hold the Power key down for 4 beeps (signifies 3 or more

seconds) then release.

• Turn the MX1-IS on

Hold the Power key down until the display turns on.

• Force the Suspend state

Tap the Power key (1 beep). The Suspend state is useful for

breaks or brief periods when the unit will not be used.

• Wake from Suspend

Tap the Power key to wake the MX1-IS from Suspend

(before the 5 minute timer expires).

Off Timer and Critical Suspend Mode

The MX1-IS is automatically turned off when the Off Timer expires. The Off Timer runs when the

MX1-IS is in Critical Suspend mode. The MX1-IS automatically goes into Critical Suspend when

the Main Battery is reaching the critical power mark. The Off Timer default is 5 minutes. The

value can be adjusted using the BIOS Setup.

Important:

The MX1-IS Main Battery must be replaced when the unit enters Critical Suspend.

Turn the unit off before replacing the Main Battery.

14 Power Button Functions

MX1 I-Safe User’s Guide E-EQ-MX1ISOGWW-J

Power Status and the Status LED

Figure 13 Power Status and the Status LED

The Status LED is located next to the LXE logo on the MX1-IS. The LED changes color and state

depending on power status.

Status LED Condition

Off MX1-IS is Off.

The MX1-IS is powered On and the display is On.

Steady Green The MX1-IS is powered On and the display is Off. Press any key to

turn the display On.

Blinking Green The MX1-IS is in the Suspend state. Tap the Power key to exit the

Suspend state. Hold the Power key down for 4 beeps to turn the MX1-

IS off. There may be a brief wait while the MX1-IS synchronizes with

the RF network.

Steady Red Main Battery Low Warning or Low Main Battery. Replace the main

battery.

Blinking Red Main Battery Power Failure or the Main Battery is depleted. Replace

the main battery. The MX1-IS will turn off in 5 minutes (default or the

value selected in BIOS Setup for the Off Timer limit) if no action is

taken.

Power Management and the

Keypad

Status LED is Steady Green. When the MX1-IS is in the Display Off state, any keypress returns

the computer to the On state and the display activates. The key pressed (key value) is not sent to

the Operating System or application.

If the 2

, Ctrl, Shift, or Alt keys were active (and the icons were on the display) when the MX1-IS

entered Display Off or Suspend, the modifier keys and their icons are cleared from the display

when the MX1-IS wakes up.

Page is loading ...

LXE MX1-IS User manual

Brand: LXE

Model: MX1-IS

Type: User manual

This manual is also suitable for

MX1 Intrinsically Safe

Download PDF

report

LXE MX1-IS User manual

This manual is also suitable for

LXE MX1-IS User manual

Related papers

Other documents