Kenmore 58714402400 Installation guide

Brand: Kenmore

Model: 58714402400

Category: Dishwashers

Type: Installation guide

This manual is also suitable for

Installation

Instructions

Built-In

Dishwasher

ff youhave questions,call 1-800-4-MY-HOME® (1-800-469-4663)or visit our website at:

www.sears.com

BEFORE YOU BEGIN

Readtheseinstructionscompletelyand

carefully.

IMPORTANT - Observeallgoverning

codesandordinances.

• Note to Installer - Besureto leavetheseinstructionsfor

theconsumer'sandlocalinspector'suse.

• Note to Consumer - Keeptheseinstructionswith your

Owner'sManualfor future reference.

• Skill Level - Installationof thisdishwasherrequiresbasic

mechanicalandelectricalskills. Proper installation is the

responsibility of the installer. Product failure due to

improper installation is not covered under the

SEARS Appliance Warranty.

• Completion Time - 1 to 3 Hours. New installations require

moretimethan replacementinstallations.

IMPORTANT- ThedishwasherMUST

beinstalledto allow for future removalfrom the enclosureif

serviceis required.

If youreceiveda damageddishwasher,youshouldimmediately

contactyourdealeror builder.

Optional Accessories - Seethe Owner'sManualfor

availablecustompanelkits.

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS

shown throughout these instructions. While

performing installations described in this booklet,

gloves, safety glasses or goggles should he worn.

WARNING

To reducetherisk of electricalshock,fire, or

injuryto persons,the installermustensurethat

the dishwasheris completelyenclosedat the

time of installation.

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

Installation Preparation

PARTS SUPPLIED:

[] Two#8 Phillipsflat headwoodscrews,5/8" longtosecuredishwasher

toundersideofcountertop(inliteraturepackage).

[] Two Phillipshead,colormatchedtoekickscrews(inliteraturepackage).

2 WoodScrews

2ColorMatched

ToekickScrews

ScrewType

HoseClamp

MATERIALS YOU WILL NEED:

[] Ferrule,compressionnutand90° Elbow(3/8"NPTexternal

threadononeend,oppositeendsizedto fit watersupply)

[] Threadsealtape

[] ULListedwire nuts(3)

Materials for New Installations Only:

[] Air gapfor drainhose,ifrequired

[] Wasteteefor houseplumbing,if applicable

[] Electricalcableorpowercord,ifapplicable

[] Screwtype hoseclamps

[] Strainrelieffor electricalconnection

[] Handshut-offvalve

[] Waterline3/8" min.copper

[] Couplerfor extendingdrainline,if applicable

,an,S ut

OffValve

90° Elbow,Ferrule

andCompressionNut

Thread

SealTape

WireNuts (3)

ElectricalCable

(orPowerCord,if applicable)

WasteTee

AirGap

HotWaterline

ScrewType

HoseClamps

StrainRelief

Coupler

TOOLS YOU WILL NEED:

[] Phillipsheadscrewdriver

[] 5/16" and1/4" nutdriver

[] 6" Adjustablewrench

[] Level

[] Carpenterssquare

[] Measuringtape

[] Safetyglasses

[] Flashlight

[] Bucketto catchwaterwhenflushingtheline

[] Gloves

Phill_

Screwdriver

For New Installations Only:

[] Tubingcutter

[] Drillandappropriatebits

[] Holesawset

Flashlight

Gloves

1/4"

and5/t6"

Nutdriver

Bucket

6" Adjustable

Wrench

SafetyGlasses

HoleSawSet

Level

TubingCutter

Carpenters

Square

........... i

i ,hhl,hhhhhhhhl

MeasuringTape

Installation Preparation

PREPARE DISHWASHER ENCLOSURE

• Thedishwashermustbe installedsothat drainhoseis nomore

than 10feet in lengthfor properdrainage.

• Thedishwashermustbe fully enclosedonthe top, sidesand

back,andmustnot supportanypart of theenclosure.

32.5"

Undersideof

Countertop

toFloor

Square

17-5/8"Min. and

18"Max. Plumb

Figure A

PlumbingandElectricService

Must EnterShadedArea

• Theroughcabinetopeningmustbe at least 24" deepand

17-5/8"to 18" wide.Theopeningshouldbe32.5" max.height.

CLEARANCES: When

installed into a corner,

allow 2" rain.clearance

between dishwasher and

adjacent cabinet,wall or

other appliances.Allow

25-5/8" rain. clearance

from the front of the

dishwasher for door

opening.FigureB

/[ Countertop

25-5/8"

}_ ClearanceforDoor

Opening2 Minimum

Figure B

Note: ADAinstallation,(32-I/2") beneath34" highcounter-topsmaybe

accomplishedbyadjustingthetcekick andlevelinglegs.

DRAIN REQUIREMENTS

• Followlocalcodesandordinances.

• Donotexceed10feet distanceto drain.

• Donotconnectdrainlinesfrom otherdevicesto the

dishwasherdrain hose.

• Dishwashermustbeconnectedto waste linewith anairgap

(notsupplied)or32"minimumhighdrainloop,dependingon

localcodesandordinancestopreventbackflow intothe

dishwasher.

• Air gap mustbeusedif wastetee or disposerconnectionis

lessthan 18" abovethe floor to preventsiphoning.

DRAIN PREPARATION

Thetypeofdraininstallationdependsonanswerstothe

following questions:

[] Dolocalcodesor ordinancesrequireanair gap?

[] Willwastetee ordisposerconnectionbelessthan18"

abovethefloor?

[] Willinstallationhavea drainlooplessthan32" abovefloor?

If theanswerto ANY ofthe3 questionsaboveisYES,

Method 1 MUST be used. Otherwiseeither Method 1 or

Method2 may beused.FigureCorFigureD.

CAUTION:

An air gapMUSTBEUSEDifthe drainhoseisconnectedto

waste tee or disposerlower than 18" abovethefloor.

Failureto providethe properdrainconnectionheightwith air gap

or 32" minimum,highdrainloopwill result in improperdraining

of the dishwasher.

Method 1 - Air Gap with Waste Tee or Disposer

Figure C

Method 2 - High Drain with Waste Tee or Disposer

Providea methodto attach drainhoseto undersideof countertop.

Mn.III ',..fJ.1.8" _i

Figure D

_f__

_2"

in.

_Mlin.-%.

Installwaste tee or disposerandair gapaccordingto

manufacturer'sinstructions.

CABINET PREPARATION

• Drilla 1-1/2" dia.holeinthe cabinetwall within the shaded

areasshownin FigureA for the drainhoseconnection.Thehole

shouldbesmoothwith nosharpedges.

Installation Preparation

PREPARE ELECTRICAL WIRING

WARNING

FORPERSONALSAFETY:Removehousefuse

or opencircuit breakerbeforebeginning

installation.Oonotusean extensioncordor

adapterplugwith this appliance.

Electrical Requirements

= This appliancemustbesuppliedwith 120V, 60 Hz.,and

connectedtoanindividualproperlygroundedbranchcircuit,

protectedby a 15 or 20 amperecircuit breakeror timedelay

fuse.

• Wiringmustbe2 wire with ground.

• If the electricalsupplydoesnot meetthe aboverequirements,

call a licensedelectricianbefore proceeding.

Grounding Instructions - Cable Direct

Thisappliancemustbeconnectedto a groundedmetal,permanent

wiring system,oranequipmentgroundingconductormustberun

with thecircuitconductorsandbeconnectedtotheequipment

groundingterminalorleadontheappliance.

Grounding Instructions - Power Cord Models

Thisappliancemustbegrounded.In theeventof amalfunctionor

breakdown,groundingwill reducetherisk of electricalshockby

providinga pathof least resistancefor electric current.Theplug

mustbe pluggedinto anappropriateoutlet that is installedand

groundedin accordancewith localcodesandordinances.

WARNING

Theimproperconnectionof theequipment

groundingconductorcanresult in a risk of

electric shock.Checkwith a qualified

electricianor servicerepresentativeif you

arein doubtthat the applianceis properly

grounded.

/ I

I \

I \\

1-1/2" Dia.

Hole(Max.)

from

Cabinet

Figure E

White

Cabinet Preparation & Wire Routing

• Thewiring mayentertheopeningfrom eitherside, rearor the

floor within theshadedarea.

• Cuta 1-1/2" max.dia.holeto admitthe electricalcable.Thehole

mustbefree of sharpedges.If thecabinetwall is metal,the

holeedgemust becoveredwith a bushing.

• Cabledirectconnectionsmay passthroughthesameholeasthe

drainhoseandhot water line,if convenient.If cabinetwall is

metal,thehole edgemust becoveredwith a bushing.

NOTE: Powercordswith plugmust passthrougha separate

hole.

Electrical Connection to Dishwasher

Electricalconnectionis ontheright front of dishwasher.

• Forcabledirect connectionsthecablemustberoutedasshown

in FigureE.Cablemustextenda minimumof 24" from the rear

wall.

• Forpowercordconnections,install a 3-pronggroundingtype

receptacle.Thepower-supplyreceptaclefor the applianceshall

beinstalledin a cabinetor ona wall adjacentto the

undercounterspacein whichthe applianceis to be installed.

Installation Instructions

PREPARE HOT WATER LINE

• Thelinemayenterfrom eitherside, rearor floor within the

shadedareashownin FigureF.

• Thelinemay passthroughthesameholeasthe electrical

cableanddrainhose.Or,cut an additional1-1/2" dia.holeto

accommodatethe water line.

If powercordwith plugis used,water linemustnot pass

throughpowercordhole.

-1-

rl i

Shut-off 1-1/2" Dia.

Valve H

Hot£.....

From

Cabinet

Cabinet Face

3" From Floor

Figure F

Water Line Connection

• Turnoff thewater supply.

• Install a handshut-off valvein an accessiblelocation,such as

underthe sink.(Optional,but stronglyrecommendedandmay

be requiredbylocal codes.)

• Waterconnectionis on the left sideof the dishwasher.Install

the hot water inlet line,usingnolessthan 3/8" O.D.copper

tubing.Routethe line asshownin FigureFandextend

forward at least 18" from rearwall.

• Adjust water heaterfor 120°Fto 150°Ftemperature.

• Flushwater lineto cleanout debris.

• Thehot water supplyline pressuremustbe 20-120 PSI.

BEFORE YOU BEGIN

Locateandset asidethe packagecontaining

2 Phillipsheadcountertopmountingscrews and

2 additionaltoekick screws (locatedin the literature

package).

ISTEP 1 I CHECK DOOR BALANCE

Tocheckthedoorbalance,holdthetopofthedishwasher

firmly.

Decrease

Figure G

• Openthe doorslowly, if the door dropswhenreleased,

increasespringtension.If the door closeswhenreleased,

decreasetension.

• Pullthe springadjustmentpinout of the holes,insert in the

next highestor lowest holeandtest again.

• Adjust bothdoorspringsto the sametension.

• Continuemovingthe springpinuntil dooris balanced.

CAUTION:

Openingthedoorwill causethe dishwasher

to tip forward. Do not open the door until you are

ready to install the dishwasher. If

it isnecessaryto openthedoor,holdthe ,/_

topof thedishwashersecurelywith one

(

handandholdthedoorwiththeother

hand.

Installation Instructions

[STEP 21 ADJUST LEVELING LEGS

• Movethedishwashercloseto theinstallationlocationandlay

it onits back.

Adjust to

Installation

Height

Figure H

_ o

• Measureinstallationheightanddishwasherheight.Extend

levelinglegsout from the dishwasherbase,1/4" lessthan

installation height.

[STEP31REMOVE TOEKICK

• Removethe4 toekick screws.Lift off the 2 piecetoekick.

Figure J

lSTEP 4] INSTALL 90 ° ELBOW

• Wrap90° elbowwith threadsealtape.

• Installa 90° elbowontothe water valve.

Fill

Hose

90°

Elbow

Thread

Figure L SealTape

Water

Valve

Bracket

• Donot overtighten 90° elbow, water valve bracketcould

bendor water valvefitting couldbreak.

• Positiontheendof theelbowto facethe rearof the

dishwasher.

Installation Instructions

[STEP 51POSITION WATER LINE

AND HOUSE WIRING

• Positionwater supplylineandhousewiring onthe floor of the

openingto avoidinterferencewith baseof dishwasherand

componentsunderdishwasher.

Figure M

House-

Line Wiring

[STEP 61INSERT DRAIN HOSE

THROUGH CABINET

• Insertdrainhoseinto cabinetwall hole.If a powercordis

used,guidethe endthrougha separatehole.

Insulati

Blanket

_ Maximum

Drain Hose

th 10'

3rain

Hose

Hoi

Wiring

PowerCord

(If Used)

Figure N

TIP: Positionwater line andhousewiring onthe floor to avoid

interferencewith baseof dishwasher.

lSTEP 7 ISLIDE DISHWASHER

PARTIALLY INTO CABINET

DO NOT PUSH AGAINST FRONT PANELWITH KNEES.

DAMAGE WILL OCCUR.

• Slidedishwasherinto theopeninga few inchesat a time.

DoNot PushAgainst

FrontDoor PanelWith

Knee.Damageto The

DoorPanelWill Occur.

Figure 0

• Asyou proceed,pullthe drainhosethroughthe openingunder

thesink. Stoppushingwhenthe dishwasheris a few inches

forward of adjacentcabinetry.

• Makesuredrainhoseis not kinkedunderthe dishwasherand

thereis nointerferencewith the water lineandwiring or any

othercomponent.

Installation Instructions

[STEP 81

POSITION DISHWASHER UNDER COUNTERTOP

• Checkto besurethat wires aresecureunderthedishwasher

andnot pinchedor in contact with doorspringsor other

dishwashercomponents.

TIP: Checktub insulationblanket,if equipped.It shouldbe

positionedsoit is notbunchedupor interferingwith door

springs.Checkbyopeningandclosingthe door.

• Pushdishwasherinto cabinet.Thefront cornersof the

dishwasherdoorshouldbeflush with cabinetdoors.Be

carefulnot to dentfront panelswith kneesor damage

countertopor cabinetswith dishwasherparts.

Do Not PushAgainst_

Front DoorPanelWith _.

Knee.Damageto The \

Door PanelWill Occur.

Figure P

RepositionDishwasher

/ , \ byGraspingBoth

With Hands

[ STEP 9 1 LEVEL DISHWASHER

IMPORTANT -Oishwasher must be

levelfor properdishrackoperationandwash performance.

• Placelevelondoor

andrack track inside

thetubasshownto

checkthat the

dishwasheris level.

Figure Q

/ \

to B_ ___S _i_e

• Levelthe dishwasherby

adjustingthe four leveling

legs individually.

Turn

to Adj

Figure R

TIP: Pulllowerrack out, abouthalfway. Checkto besuretherack

doesnot roll forward or back intodishwasher.If the rackrolls in

eitherdirection,the dishwashermust beleveledagain.

• If doorhits thetub, thedishwasheris not installedcorrectly.

Adjust levelinglegsto aligndoorto tub.

Installation Instructions

[STEP 101SECURE DISHWASHER

TO CABINET

Thedishwashermustbesecuredto thecountertop.

• Positionthe dishwashersothat the tub flangealignswith the

front face of thecabinetframe.

IMPORTANT: Checkto besurethedishwasheris centeredin

the openingandthere isno interferencewith adjacentcabinets

whenopeningor closingthe door.

Align Tub

Flange

to Front

Faceof

Cabinet

Frame

Figure S

• Fastenthe dishwasherto the undersideof the countertop

with the 2 Phillipsscrews provided.

IMPORTANT- Drivescrews

straight andflush. Protrudingscrew headswill scratchthe top

of the control panelandcaninterferewith doorclosing.

lSTEP 11 ICONNECT WATER

SUPPLY

Connectwater supplyto 90° elbow.

• Slidecompressionnut, thenferruleoverendof water line.

• Insertwater line into 90° elbow.

• Slideferruleagainstelbow andsecurewith compressionnut.

Hot Water

_° Elbow SupplyLine

Figure T

IMPORTANT- Checktobesurethat

doorspringdoesnotruborcontactthefill hoseorwater supply

line.Testbyopeningandclosingthedoor.Re-routethelinesif a

rubbingnoiseor interferenceoccurs.

Installation Instructions

[STEP 12 ICONNECT DRAIN LINE

FOLLOWALL LOCALCODESAND ORDINANCES.

Thedrainhosemoldedendwill fit 5/8", 3/4" or 1" diameter

connectionsonthe air gap,wastetee or disposer.Cuton the

markedline asrequiredfor your installation.

Cutting Lines

IMPORTANT:Do not cut corrugated

portion of hose

DRAIN LINE INSTALLATION

• Connectdrainlinetoair gap,wastetee ordisposerusingeither

previouslydeterminedmethod.

Method 1 - Air gap with waste tee or disposer

Figure U Waste Tee Installation DisposerInstallation

Figure W

• If a longerdrainhoseisrequired,addupto 42" of lengthfor a

total of 10ft. to thefactory installedhose.Use5/8" or7/8"

insidediameterhoseanda couplerto connectthe two hose

ends.Securethe connectionwith hoseclamps.

HoseClamp

Coupler

Figure V

• Securethe drainhoseto the air gap,waste tee or disposer

with clamps.

NOTE:TOTALDRAINHOSELENGTHMUSTNOTEXCEED

10 FEETFORPROPERDRAINOPERATION.

Method 2 - High drain loop with waste tee or disposer

Fastento underside

_ _ of counte[top

Waste Tee Installation

Fastento underside

_/._ of countertop

32"

DisposerInstallation

Figure X

IMPORTANT -

Whenconnectingdrainlinetodisposer,

checkto besurethatdrain plughasbeen

removed.DISHWASHERWILLNOTDRAIN

IF PLUGISLEFTINPLACE.

_ emove

Disposer

Plug

TIP: Avoid unnecessaryservicecall charges.Always be sure

disposerdrainplug hasbeenremovedbeforeattachingdishwasher

drainhoseto the disposer.

Installation Instructions

[STEP 13 ICONNECT POWER

SUPPLY

Skip this step if equipped with power cord,

Verify that power is turned off at the source,

• Removejunctionbox cover"A".

• Locatethe threedishwasherwires, (white, blackand green)

with strippedends.Insert dishwasherwires throughthe

smallholein thejunction box"B'.

• Securehousewiring to the bottomof thejunction boxwith a

strain relief"C'.

• Userwire nuts to connectincominggroundto green,white to

white andblacktoblack"O".

• Replacejunction boxcover"E". Checkto besurethat wires

arenot pinchedunderthe cover.

E. ReplaceJunctionBoxCover

WARNING

If housewiring is not 2-wirewith ground,

a groundmustbeprovidedby the installer.

Whenhousewiring is aluminum,besureto

useULListedanti-oxidantcompoundand

aluminum-to-copperconnectors.

ISTEP 14 IPRE-TEST CHECKLIST

Review this list after installing your dishwasher to

avoid charges for a service call that is not covered

by your warranty.

[] ChecktobesurepowerisOFF.

[] Opendoorand removeall foam andpaperpackaging.

[] Locatethe Owner'sManualin the literature package.

[] Readthe Owner'sManualfor operatinginstructions.

[] Checkdooropeningandclosing.If doordoesnot openand

closefreely or tendsto fall, checkspringadjustments.See

Step1.

[] Checkto besurethat wiringis secureunderthe dishwasher,

not pinchedor in contact with doorspringsor other

components.SeeStep9.

[] Checkdooralignmentwith tub. If doorhits tub, level

dishwasher.SeeStep10.

[] Pulllower rackout, abouthalf way. Checkto besureit does

not roll backorforward onthe door.If therack moves,adjust

levelinglegs.SeeStep 10.

[] Checkdooralignmentwith cabinet.If doorhitscabinet,

repositionor releveldishwasher.SeeStep 10.

[] Verify water supplyanddrainlinesarenot kinkedor in

contact with othercomponents.Contactwith motoror

dishwasherframe couldcausenoise.SeeStep8.

[] Turnonthesink hot water faucet andverify water

temperature.Incomingwater temperaturemust bebetween

120°F and150°F. A minimumof 120°F temperatureis

requiredfor best wash performance.See"PrepareHot Water

Line",page5.

[] Add2 quartsof water to the bottomof thedishwasherto

lubricatethe pumpseal.

[] Turnon water supply.Checkfor leaks.Tightenconnections

if needed.

[] Removeprotectivefilm if presentfrom the controlpaneland

door.

Installation Instructions

[STEP 151DISHWASHER WET TEST

[] Turnonpowersupply(orplugpowercordintooutlet,ifequipped).

[] Turndialto Normal"Wash"position.

[] Closedoor.

[] Checkto besurethat water entersthedishwasher.If water doesnot

enterthedishwasher,checkto besurethat water andpowerare

turnedon.

[] Checkfor leaksunderthedishwasher.If a leakisfound,turn power

supplyoff, thentightenconnections.Restorepowerafter leakis

corrected.

[] Checkfor leaksaroundthedoor.A leakaroundthedoorcouldbe

causedby doorrubbingorhitting againstadjacentcabinetry.Reposition

thedishwasherif necessary.SeeStep9.

[] Thedishwasherwill drainandturn off about5to 7minutesafter the

first fill. Checkdrainlines.If leaksarefound,turn poweroff atthe

breakerandcorrectplumbingasnecessary.Restorepowerafter

correctionsaremade.SeeStep12.

[] Opendishwasherdoorandmakesuremost ofthewater hasdrained.

If not,checkthat disposerplughasbeenremovedand/orairgapisnot

plugged.SeeStep13.Alsocheckdrainlineforkinking.

[] Runthedishwasherthroughanotherfill anddraincycle.Checkfor

leaksandcorrectif required.

[] At theendofdrain,opendoorandturn dialto OFFposition.

ISTEP 161REPLACE TOEKICK

o kiok ql

Adjust_

orDowr_

FigureY

• Place2-piecetoekickagainstthe legsof the dishwasher.

• Placethe innertoekick piece(with slots) againstthetoekick

bracket.Theslots shouldalignwith toekickbracketscrew

holes.Allow thetoekick to touchthe floor.

• Placelargertoekick overthe innerpieceandinstall 4 toekick

screws.

• Useadditional2 screwsthat are providedfor installations

over33-1/2" high.

• Usebothtoekick piecesfor all installationheights.

STEP 171LITERATURE

Be sure to leave completeliterature package and installation

instructions with consumer.

Kenmore 58714402400 Installation guide

Brand: Kenmore

Model: 58714402400

Category: Dishwashers

Type: Installation guide

This manual is also suitable for

Download PDF

report

Kenmore 58714402400 Installation guide

This manual is also suitable for

Kenmore 58714402400 Installation guide

Related papers

Other documents