Electrolux EFD18000U User manual

Brand: Electrolux

Model: EFD18000U

Category: Electric blankets/pillows

Type: User manual

Electrolux EFD18000U is a user-friendly built-in down draught extractor that makes cooking more comfortable and enjoyable. With 4 fan levels, including an intensive setting, it efficiently removes odors, smoke, and grease from your kitchen. For added convenience, the timer function allows you to set the extractor to run for a specific duration, automatically turning off when the time expires.

user manual

Down draught extractor

EFD18000U

We were thinking of you

when we made this product

electrolux 3

Welcome to the world of Electrolux

Thank you for choosing a first class

product from Electrolux, which hopefully

will provide you with lots of pleasure in

the future. The Electrolux ambition is to

offer a wide variety of quality products

that make your life more comfortable.

You will find some examples on the cov-

er in this manual. Please take a few min-

utes to study this manual so that you

can take advantage of the benefits of

your new machine. We promise that it

will provide a superior User Experience

delivering Ease-of-Mind. Good luck!

4 electrolux contents

Contents

Operating Instructions 5

Safety instructions 5

Description of the Appliance 6

Operating the appliance 8

Cleaning and Care 11

What to do if … 13

Disposal 15

Installation Instructions 16

Assembly 19

Installing more than one

Frontline hob 21

Guarantee/Customer Service 26

he following symbols are used in this user information:

Warning! This must be read! Important advice for the safety of persons and

information on avoiding damage to the appliance

3 General information and advice

2 Information on environmental protection

z Dangerous voltage

operating instructions electrolux 5

Operating Instructions

Safety instructions

Please comply with these instructions. If

you do not, any damage resulting is not

covered by the warranty.

Correct use

• This appliance is not intended for

use by children or other persons

whose physical, sensory or mental

capabilities or lack of experience and

knowledge prevents them from us-

ing the appliance safely without su-

pervision or instruction by a

responsible person to ensure that

they can use the appliance safely.

• Do not leave the appliance unattend-

ed during operation.

• The appliance must not be used as a

work surface or as a storage surface.

• Additions or modifications to the ap-

pliance are not permitted.

Children’s safety

• Small children must be kept away

from the appliance.

• Only let bigger children work on the

appliance under supervision.

General safety

• The appliance may only be installed

and connected by trained, registered

service engineers.

• Built-in appliances may only be used

after they have built in to suitable

built-in units and work surfaces that

meet standards.

• In the event of faults with the appli-

ance or damage to the glass ceramic

(cracks, scratches or splits), the ap-

pliance must be switched off and

disconnected from the electrical

supply, to prevent the possibility of

an electric shock.

• Repairs to the appliance must only

be carried out by trained registered

service engineers.

Safety during use

• Remove stickers and film from the

glass ceramic.

• When the appliance is switched on,

do not flambé directly next it.

• In the event of fire, switch off appli-

ance.

• Smother fire using a cover, never use

water to put out.

• Switch off the appliance after each

use.

Safety when cleaning

• For cleaning, the appliance must be

switched off.

• For safety reasons, the cleaning of

the appliance with steam jet or high-

pressure cleaning equipment is not

permitted.

How to avoid damage to the appli-

ance

• The glass ceramic can be damaged

by objects falling onto it.

6 electrolux description of the appliance

Description of the Appliance

Cooking surface layout

Control panel layout

Upper

casing

Control panel

Frontline strip

Shaft of down draught

extractor

Filter

Fin

Timer indicator

Position selection

Timer

Fan level

display

Intensive fan

On/Off

Fan level selection

description of the appliance electrolux 7

Touch Control sensor fields

The appliance is operated using Touch

Control sensor fields. Functions are

controlled by touching sensor fields and

confirmed by displays and acoustic sig-

nals.

Touch the sensor fields from above,

without covering other sensor fields.

Displays

Sensor field Function

On / Off To switch the appliance on and off

Increase settings To increa s e p o sitio n

Reduce settings To reduce position

Fan To se t f a n leve l

Intensive fan To switch intensive fan on/off

Timer Timer selection

Display Description

¾ no power setting set

¿ - Á Fan levels Fan level is set

e Clean filter Filter must be cleaned

Safety cut-out Safety cut-out has been activated

8 electrolux operating the appliance

Operating the appliance

Switching the appliance on and off

After switching on, within approx.

10 seconds a function must be set,

otherwise the appliance automati-

cally switches itself off.

Let the down draught extractor run

for a few minutes before and after

preparing a meal.

While the down draught extractor is

working, windows in the room

should be closed. A window in a

neighbouring room can be open.

Control panel Display Pilot light

To sw i t c h on Touch for 2 seconds ¾ lights up

To sw i t c h off Touch for 1 second none goes out

operating the appliance electrolux 9

Setting position of down draught extractor

Increasing extractor position

Reducing extractor position

Retaining extractor position

If the appliance becomes blocked

when changing the position, it

switches off automatically.

Setting fan level

Switching off fan level

Step Control panel Position of extractor

1. Touch once Middle

2. Touch To p

Fan level 1 is switched on.

Step Control panel Position of extractor

1. Touch Middle/bottom

The appliance switches off in the lowest position.

Step Control panel Position of extractor

1. Touch Current position is retained

The appliance switches off.

Step Control panel Fan level display Fan power

1. Touch once ¿ 150 m³/h

2. Touch once À 220 m³/h

3. Touch once Á 345 m³/h

Step Control panel Display

1. To u c h ¾

The fan level is switched off.

10 electrolux operating the appliance

Switching intensive fan on and off

The intensive fan function makes ex-

tra power available for 5 minutes. After

that the appliance switches off automat-

ically or switches back to the previously

set fan level.

Using the timer

After the time set has elapsed, the suc-

tion switches off. The down draught ex-

tractor remains in the top position.

Setting the time

Switching timer function off

Automatic switch off

• If one or more sensor fields are cov-

ered for longer than approx.

10 seconds, e.g. by a pan cloth lying

on them, the appliance switches off

automatically.

• If the appliance is not switched off af-

ter 6 hours or the fan level is not al-

tered, the appliance automatically

switches itself off.

• Before the appliance is used again,

must be touched.

Control panel Fan power

To sw i t c h on Touch 480 m³/h

To sw i t c h off Touch previously set fan power

Step Control panel Display

1. To u c h once 60 seconds

2. Touch for longer ... 05...10...15... 20 (5 minute increments

for easier setting)

The time is set.

The time counts down.

Step Control panel Display

1. To u c h The remaining time counts up to 00.

The timer function is switched off.

cleaning and care electrolux 11

Cleaning and Care

Important: A blocked grease filter

can ignite. Keep appliance clean.

Important: Sharp objects and abra-

sive cleaning materials will damage

the appliance. Clean with a damp

cloth and washing up liquid.

Important: Residues from cleaning

agents will damage the appliance.

Remove residues with a damp cloth

and washing up liquid.

Important: Risk of fire! Cleaning

must be performed according to the

instructions in these operating in-

structions.

Glass ceramic, shaft of down

draught extractor

1. Wipe the appliance with a damp

cloth and a little washing up liquid.

2. Dry the appliance using a clean

cloth.

Scratches or dark stains on the

glass ceramic cannot be removed

but do not affect the functioning of

the appliance.

Upper housing

1. Switch on down draught extractor

and move to the top position.

2. Remove upper housing.

3. Wipe the appliance with a damp

cloth and a little washing up liquid.

4. Dry the appliance using a clean

cloth.

Filter

After 30 hours of operation the filter

must be cleaned, 0 appears.

Important: Fingers can get caught.

Only remove filter or upper casing

when appliance is dismantled.

1. Switch on down draught extractor

and move to the top position.

2. Switch off fan level.

3. Remove upper casing and place on

something soft.

4. Press in and remove the springs of

the filter.

5. Take filter out.

6. Clean filter with hot water and wash-

ing up liquid or clean in the dish-

washer.

If cleaned in the dishwasher, the fil-

ter can become discoloured, but

this does not affect the functioning

of the filter.

7. Install filter, springs and upper casing

in reverse order.

12 electrolux cleaning and care

The filter must be completely dry

before being installed.

8. Reset filter sensor by pressing

and at the same time for

3seconds.

9. 0 goes out.

If the filter is cleaned before the 30

hours of operation have elapsed, it

can be reset in the same way.

If the electricity supply is interrupt-

ed, the filter sensor automatically

resets itself.

Removable Frontline strip

The aluminium Frontline strip fastens on

by means of magnets. It is easy to re-

move by hand and can be cleaned with

detergent. Please do not use any scour-

ing agents or sponges that scratch. Do

not clean the strip in the dishwasher.

what to do if … electrolux 13

What to do if …

Problem Possible cause Remedy

The appliance cannot be

switched on or is not operating

More than 10 seconds have

passed since the appliance

was switched on

Switch appliance on again

Several sensor fields were

touched at the same time

Only touch one sensor field

The sensor fields are partly

covered by a damp cloth or

with liquid

Remove the cloth or the liquid.

Switch appliance on again

Electronics fault Disconnect appliance from the

electrical supply for a few min-

utes. (Take the fuse out of the

house’s wiring system.)

If the appliance still does not

operate after switching on

again, call the Customer Care

Department

Fuses keep blowing Too many electrical appliances

are connected

Switch off electrical appliances

The fan is switched off, but the

down draught extractor is

raised

There was a power cut during

operation

Switch on down draught ex-

tractor and touch

is displayed Filter sensor has responded. Clean filter and reset filter sen-

sor (see section “Cleaning and

Care”)

Down draught extractor has

switched off automatically and

cannot be switched on again

Vertical adjustment of the

down draught extractor has

become jammed

Disconnect appliance from the

electrical supply for a few min-

utes. (Take the fuse out of the

house’s wiring system.)

If the appliance still does not

operate after switching on

again, call the Customer Care

Department

14 electrolux what to do if …

If you are unable to remedy the

problem by following the above

suggestions, please contact your

local Service Force Centre.

Warning! Repairs to the appliance

are only to be carried out by quali-

fied service engineers. Considera-

ble danger to the user may result

from improper repairs.

If the appliance has been operated

incorrectly, the engineer's visit will

be chargeable, even during the war-

ranty period.

disposal electrolux 15

Disposal

Packaging material

The packaging materials are envi-

ronmentally friendly and can be re-

cycled. The plastic components are

identified by markings, e.g. >PE<,

>PS<, etc. Please dispose of the

packaging materials in the appro-

priate container at the community

waste disposal facilities.

Old appliance

The symbol

W on the product or on

its packaging indicates that this

product may not be treated as

household waste. Instead it shall be

handed over to the applicable col-

lection point for the recycling of

electrical and electronic equipment.

By ensuring this product is dis-

posed of correctly, you will help pre-

vent potential negative

consequences for the environment

and human health, which could oth-

erwise be caused by inappropriate

waste handling of this product. For

more detailed information about re-

cycling of this product, please con-

tact your local city office, your

household waste disposal service

or the shop where you purchased

the product.

16 electrolux installation instructions

Installation Instructions

Safety instructions

Warning! This must be read!

The laws, ordinances, directives and

standards in force in the country of use

are to be followed (safety regulations,

proper recycling in accordance with the

regulations, etc.)

Installation may only be carried out by a

qualified electrician.

The minimum distances to other appli-

ances and units are to be observed.

Anti-shock protection must be provided

by the installation, for example drawers

may only be installed with a protective

floor directly underneath the appliance.

The cut surfaces of the worktop are to

be protected against moisture using a

suitable sealant.

The sealant seals the appliance to the

work top with no gap.

Important: If the down draught extractor

is operated at the same time as a gas

appliance, there must be sufficient

draught in the room.

Important: If the down draught ex-

tractor is operated at the same time

as a fireplace, the pressure in the

room must be below 4 Pa (4 x 10

-5

bar).

Important: If the mains cable is de-

fective, it must only be replaced by a

qualified electrician or our Custom-

er Care Department in order to pre-

vent hazards.

z Risk of injury from electrical

current.

• The electrical mains terminal is live.

• Make electrical mains terminal free of

voltage.

• Follow connection schematic.

• Observe electrical safety rules.

• Ensure anti-shock protection by in-

stalling correctly.

• The appliance must be connected to

the electrical supply by a qualified

electrician.

z Risk of injury from electrical

current.

• Loose and inappropriate plug and

socket connections can make the

terminal overheat.

• Have the clamping connections cor-

rectly installed by a qualified electri-

cian.

• Use strain relief clamp on cable.

A device must be provided in the electri-

cal installation which allows the appli-

ance to be disconnected from the mains

at all poles with a contact opening width

of at least 3 mm.

Suitable isolation devices include line

protecting cut-outs, fuses (screw type

fuses are to be removed from the hold-

er), earth leakage trips and contactors.

Connect down draught extractor to an

air-tight vent hose or vent pipe with a

120 mm diameter and at least 1 m long.

installation instructions electrolux 17

Important: Do not connect down

draught extractor to the voltage

supply until an adequate air outlet

has been provided.

Do not connect vent hose or vent

pipe to an air shaft, flue or similar

which is already in use.

If several Frontline appliances are in-

stalled, install down draught extractor

between the appliances.

Distance from flammable materials: at

least 150 mm

Important: Official regulations must

be followed when drawing off ex-

haust air.

Important: Do not conduct exhaust

air to a chimney which is used by

appliances operated with gas or

other combustible fuels.

Installing next to a gas appliance

Important: The appliance must not be

built in between two gas appliances.

Important: If a gas appliance is in-

stalled next to the down draught ex-

tractor, the down draught extractor

may only extract air on the opposite

side. Therefore the fin nearest the

gas appliance must be removed and

the supplied cover must be fitted.

18 electrolux installation instructions

To re mov e th e fin

1. Switch on down draught extractor

and move to the top position.

2. Switch off fan level.

3. Press in and remove the springs of

the filter.

4. Take f i l ter out .

5. Remove upper casing and place on

something soft.

6. Remove the two screws which hold

the fin.

7. Remove single screw that holds the

lever that closes the fin.

8. Remove the fin.

To fit cov e r

1. Lay cover on the glass ceramic.

2. Position cover on the upper housing.

3. Mark four holes on the upper casing.

Use cover as a template.

4. Remove cover and drill the four holes

in the upper casing.

5. Remove adhesive film.

6. Press cover in position on the upper

casing.

7. Affix cover with the blind rivets sup-

plied.

8. Install filter, springs and upper casing

in reverse order.

assembly electrolux 19

Assembly

min. 500 mm

20 electrolux assembly

Page is loading ...

Electrolux EFD18000U User manual

Brand: Electrolux

Model: EFD18000U

Category: Electric blankets/pillows

Type: User manual

Download PDF

report

Electrolux EFD18000U User manual

Electrolux EFD18000U User manual

Related papers

Other documents