Paxton Touchlock User guide

Type
User guide

Paxton Touchlock is a vandal-proof keypad that can be used for both internal and external doors. It is rated at IPX7, meaning it can withstand immersion in water up to 1 meter for 30 minutes. The keypad is suitable for use with the Switch2 control unit (405-321) and the PC based Net2 control unit (489-334). It has a 3m cable, which can be extended up to 30m using the appropriate cable and pull-up resistors. The keypad can be used to control a door relay, an alarm, or a bell. It can also be used to attach a QC label.

Here are some possible use cases for the Paxton Touchlock:

  • Controlling access to a building or room

Paxton Touchlock is a vandal-proof keypad that can be used for both internal and external doors. It is rated at IPX7, meaning it can withstand immersion in water up to 1 meter for 30 minutes. The keypad is suitable for use with the Switch2 control unit (405-321) and the PC based Net2 control unit (489-334). It has a 3m cable, which can be extended up to 30m using the appropriate cable and pull-up resistors. The keypad can be used to control a door relay, an alarm, or a bell. It can also be used to attach a QC label.

Here are some possible use cases for the Paxton Touchlock:

  • Controlling access to a building or room
INS-006 Date code: 201200
TOUCHLOCK keypad Stainless Steel (485-374)
Contents of kit
TOUCHLOCK keypad Stainless Steel
TOUCHLOCK keypad Stainless Steel installation instructions
TOUCHLOCK keypad Stainless Steel mounting template
220 ohm resistor
Fitting kit
Suitability
Products
The TOUCHLOCK keypad is suitable for use with the Switch2 control unit (405-321) and the PC based Net2
control unit (489-334).
Environment
The keypad will operate between –20
o
C and +70
o
C. It is rated at IPX7 and so is suitable for both internal
and external use.
Where to use the TOUCHLOCK keypad
YES NO Reason why not
Low to high use doors Completely vandal proof Keypad is exposed
Inside and outside
No need to shelter from the elements
Narrow door frames
Architecturally sensitive installations
Fitting
Using the template provided with the keypad, drill holes for the two screws and the cable.
Extend the top of the cable hole to allow the keypad to slide down during fitting.
Insert the raw plugs and screw the top 8 X 1” in only. Leave a gap of approximately 2mm between the
screw head and the face of the wall. Try the keypad on the screws and adjust as required.
Once a good fit has been achieved, thread the cable through the wall and locate the keypad. Lock it into
place with the locking screw at the bottom. If being installed into a vandal risk area, a tamper resistant
security screw can be used.
Cable
TOUCHLOCK
keypad
stainless steel
8 X 1"
Wall plugs
INS-006 Date code: 201200
Wiring
TOUCHLOCK keypads are supplied with 3m of cable. The colours of the cable cores correspond to the
labelling on the Switch2/Net2 ACU.
To save space on the board, a keypad wired to the Net2 ACU shares power and LED terminals with the
reader.
Connecting 2 keypads
If 2 keypads are to be connected to Switch2 they should be wired in parallel but the Yellow wire from the
second keypad connects into the Mauve terminal. If 2 keypads are to be connected to Net2 the second
keypad connects to the keypad 2 slot provided.
Cable Extensions
The type of cable used to extend this distance will effect the maximum distance the keypad can be extended.
All distances are assuming that the keypad is wired according to our instructions.
Maximum distance from ACU
ACU used
CR9538 CR9540
Net2 ACU 30M 30M
Switch2 ACU 30M 30M
Be sure, when extending the cable distance beyond 3M, to keep the colours the same throughout the run.
Beyond 10M pull up resistors must be fitted as shown above!
Red(5v)
Brown
Orange
Green
Yellow
* Yellow
Black
Control
unit
Inputs
Attach
Q.C. Label
here
Red
Brown
Orange
Green
Yellow
Blue
Mauve
Exit
Contact
Black
Card reader or keypad
12v
0v
N.C.
N.O.
Com
Bell
PowerDoor relay
Alarm
witch
2
S
Brown
Orange
Yellow
Green
Red
Black & White
Purple
Brown
Orange
Yellow
Green
Red & Blue
Black & White
Purple
Blue
Not connected
From Keypad
To control unit
Junction
box
Keypad 2
Yellow
Orange
Screen
White/Orange
Orange
Green
White/Green
Reader 1 Keypad 1
Brown
Yellow
Orange
Red
Brown
Orange
Green
Yellow
Blue
Mauve
Blk/Wht
Tx
Rx
Red (5V)
Green (green LED)
Blk/Wht (0V)
Brown (load)
Yellow (data)
Orange (clock)
*
* 220 Ohm resistor
supplied in the keypad fitting kit
CAT5 cable colours
5
4
3
2
1
Network
  • Page 1 1
  • Page 2 2

Paxton Touchlock User guide

Type
User guide

Paxton Touchlock is a vandal-proof keypad that can be used for both internal and external doors. It is rated at IPX7, meaning it can withstand immersion in water up to 1 meter for 30 minutes. The keypad is suitable for use with the Switch2 control unit (405-321) and the PC based Net2 control unit (489-334). It has a 3m cable, which can be extended up to 30m using the appropriate cable and pull-up resistors. The keypad can be used to control a door relay, an alarm, or a bell. It can also be used to attach a QC label.

Here are some possible use cases for the Paxton Touchlock:

  • Controlling access to a building or room

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI