Zanussi ZRB229MWO User manual

Brand: Zanussi

Model: ZRB229MWO

Category: Fridges

Type: User manual

Replacing the light bulb

Disconnect the appliance from the mains supply.

Remove the screw to release the lamp cover , the

lamp bulb is located in the lamp holder ,

unscrew the lamp in an anti-clockwise direction

until the lamp comes out of the lamp holder.

Screw a new lamp bulb (15 Watt & E14 Base)

into the lamp holder in a

clockwise direction until tight.

Replace the lamp cover and

screw back into place.

Reconnect the appliance to

The mains supply.

Replacing the light bulb

Defrosting

The freezer compartment , however , will become

progressively covered with frost. This should be

removed with the special plastic scraper provided ,

whenever the thickness of the frost exceeds 4mm.

During this operation it is not necessary to switch

off the power supply or to remove the foodstuffs.

However , when the ice becomes very thick

Defrosting

on the inner liner , complete defrosting should be

carried out as follows:

1. Pull out the plug from the wall socket ;

2. Remove any stored food , wrap it in several layers

and put it in a cool place;

3. Open the door and clean the appliance according

to 'Periodic cleaning';

Maintain and clean the freezer as following:

Sweep off the melting water with a dry cloth on each

layer of evaporator , The melting water swept down

gathers in the outlet channel which is situated in the

bottom of the appliance and can be removed

according to diagram below:

Put an adequately high bowl or dish under the

outlet.

4. When defrosting is completed , dry the interior

thoroughly; keep the scraper for future use;

5. Replace the plug in the power socket;

6. After two or three hours , reload the previously

removed food into the compartment.

Important !

Never use sharp metal tools to scrape off frost

from the evaporator as you could damage it.

Do not use a mechanical device or any artificial

means to speed up the thawing process other

than those recommended by the manufacturer.

A rise in the temperature of the frozen food during

defrosting , may shorten their safe storage life.

Important !

1

2

1.Door Stop

2.Door Stop Screw

3. Unscrew the bolts which are used to fix the

bottom hinge with the narrow head of a spanner ,

and unscrew the bottom hinge with screwdriver ,

then remove the door carefully; After that use the

middle hole of the spanner to unscrew the hinge

pin and stopper , unscrew the nut which is used

to fix the hinge pin with the wide head of a

spanner and place them in the symmetrical holes.

Fix the stopper in the middle of the

condenser , rotate the stopper 90 degrees and fixed

the position.

6. Rotate the pin by using the wide-head of the

spanner and remove the left hole cover with a

screwdriver , exchange the assembly location and fix it

as the previous method.

7. Change the handle. (which is the same method for

both fridge door and freezer door)

Remove two side of plastic hole cover and

handle with a screwdriver , fix them on the opposite

side. Put the plastic hole covers over were the handle

was originally situated.

8. Install the door carefully , adjust assembly position ,

move the hinge to left symmetrical position , then fix it

with the bolt. then use bolt to fix , install adjustable

foot to an appropriate location.

1. Tilt the refrigerator back to set at an angle.

2. Rotate the left and right adjustable front feet at

the bottom by hand , turning them anti-clockwise.

4. Remove the stopper which is under the bottom

door trim with a screwdriver , then install it to the left

symmetrical.

5. Rotate the bolt which is used to fix the middle

hinge with screwdriver , remove the middle hinge , then

carefully remove fridge door.

·

1
2
3
4
5
6
7
8
9
10
11
12

Zanussi ZRB229MWO User manual

Brand: Zanussi

Model: ZRB229MWO

Category: Fridges

Type: User manual

Download PDF

Related papers

Other documents