Zanussi ZFU628WO1 User manual

Brand: Zanussi

Model: ZFU628WO1

Category: Fridge-freezers

Type: User manual

The appliance has a fast freeze function. This

accelerates the freezing of fresh food , and at the

same time protects foodstuffs already stored from

undesirable warming.

To activate the function , do these steps:

1. Press the button to the on position.

2. The Fast Freeze indicator light should now

illuminate.

Fast Freeze function

To deactivate the function , do these steps:

1. Press the button to the off position.

2. The Fast Freeze indicator light goes out.

It is recommended that you activate the Fast

Freeze function 2 hours prior to adding fresh food

to the appliance and keep it switched on for up

to 24 hours.

→

←

Off button

On button

Sweep off the melting water with a dry cloth on each

layer of evaporator ,The melting water swept down

gathers in the outlet channel which is situated in the

bottom of the appliance and can be removed

according to diagram below:

Put an adequately high bowl or dish under

the outlet.

4. When defrosting is completed ,dry the interior

thoroughly; keep the scraper for future use;

5. Replace the plug in the power socket;

6. After two or three hours ,reload the previously

removed food into the compartment.

Important !

Never use sharp metal tools to scrape off frost from

the evaporator as you could damage it.

Do not use a mechanical device or any artificial

means to speed up the thawing process other than

those recommended by the manufacturer.

A rise in the temperature of the frozen food

during defrosting ,may shorten their safe storage life.

Important !

Defrosting

The freezer compartment ,however ,will become

progressively covered with frost. This should be

removed with the special plastic scraper

provided ,whenever the thickness of the frost

exceeds 4 mm.

During this operation it is not necessary to

switch off the power supply or to remove the

foodstuffs.

However ,when the ice becomes very thick on

the inner liner ,complete defrosting should be

carried out as follows:

1. Pull out the plug from the wall socket ;

2. Remove any stored food ,wrap it in several

layers and put it in a cool place;

3. Open the door and clean the appliance

according to 'Periodic cleaning';

Maintain and clean the freezer as following:

Defrosting

Before plugging in, ensure that the voltage and

frequency shown on the serial number plate correspond

to your domestic power supply.

Voltage can vary by ±6% of the rated voltage. For

operation with different voltages, a suitably sized auto-

transformer must be used.

The appliance must be earthed

The power supply cable plug is provided with a contact

for this purpose. If the domestic power supply socket is

not earthed, connect the appliance to a separate earth

in compliance with current regulations, consulting a

specialist technician.

The Manufacturer declines all responsibility if the

above safety precautions are not observed.

This appliance complies with the E.E.C.

Directives.

Electrical connection

Fix the stopper in the middle of the

condenser , rotate the stopper 90 degrees and fixed

the position.

3. Unscrew the bolts which are used to fix the

bottom hinge with the narrow head of a spanner ,

and unscrew the bottom hinge with screwdriver ,

then remove the door carefully; After that use the

middle hole of the spanner to unscrew the hinge

pin and stopper , unscrew the nut which is used

to fix the hinge pin with the wide head of a

spanner and place them in the symmetrical holes.

1. Tilt the refrigerator back to set at an angle.

2. Rotate the left and right adjustable front feet at

the bottom by hand , turning them anti-clockwise.

7. Install the door carefully , adjust assembly

position , move the hinge to left symmetrical

position , then fix it with the bolt. then use bolt to

fix , install adjustable foot to an appropriate

location.

4. Remove the stopper which is under the bottom

door trim with a screwdriver , then install it to the

left symmetrical.

1.Door Stop

2.Door Stop Screw

5. Rotate the pin by using the wide-head of the

spanner and remove the left hole cover with a

screwdriver , exchange the assembly location and fix

it as the previous method.

6. Change the handle. (which is the same method

for both fridge door and freezer door)

Remove two side of plastic hole cover and

handle with a screwdriver , fix them on the

opposite side. Put the plastic hole covers over

were the handle was originally situated.

C0922.5.1 (083B)-00-032010

Zanussi ZFU628WO1 User manual

Brand: Zanussi

Model: ZFU628WO1

Category: Fridge-freezers

Type: User manual

Download PDF

report

Zanussi ZFU628WO1 User manual

Zanussi ZFU628WO1 User manual

Related papers

Other documents