Paradyne 6512-A2 Installation Instructions Manual

TM

1

SuperLine Integrated Access Device

Model 6512-A2

Installation Instructions

Document Number 6512-A2-GN10-40

June 1999

TST

LINE

ALMPWR

ETHERNET

TM

98-16014a-02

BASE

PHONE

Rear

View

Front

View

SuperLine

TM

IAD

Contents

Introduction 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Front Panel Indicator Lights 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Technical Information 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Additional Notes on SuperLine IAD Operation 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Important Safety Instructions 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2

Introduction: What Your SuperLine IAD Does

Your SuperLine Integrated Access Device (IAD) is a line adapter that allows you to

connect multiple phones, fax machines, or modems using your existing phone wiring.

99-16257

TST

LINE

ALMPWR

ETHERNET

TM

Existing

Phone Line

Existing (BASE) Phone

Additional Line (PHONE 1/2)

Additional Line (PHONE 2)

Ethernet Data

Your service provider enables SuperLine service and assigns phone numbers to the

additional phone lines.

The SuperLine IAD:

H Transforms your existing single phone line into multiple phone lines to support up

to two additional phones, fax machines, or modems simultaneously.

H Provides high-speed Internet access through an Ethernet connection. (Available in

some areas. Ask your service provider about availability of this service.)

H Operates with Touch Tonet phones. The PHONE 1/2 and PHONE 2 jacks do not

support pulse dial phones. (Your existing phone, plugged into the BASE PHONE

jack, can be a pulse dial phone.)

The following figure depicts a typical home or small office configuration with several

existing phones and two additional lines. Phone filters are connected to your existing

phones to reduce interference from the new line or lines.

99-16018a-02

Wall

Jack

SuperLine

IAD

Wall

Jack

Phone

Filter

Phone

Filter

Existing

Phone

Line

Existing

Phone

Line

Existing

Phone

Line

Additional

Line

Additional

Line

3

Package Checklist

Verify that your package contains the following hardware. If any hardware is missing or

you need to order additional hardware, contact your service provider. Refer to

Technical

Information

on page 28 for further information.

SuperLine

IAD

6' RJ11

Phone

Cable

AC Power Transformer

(327-0118-0031)

99-16015a-02

Phone Filter

(6035-A1-002)

TST

LINE

ALMPWR

ETHERNET

TM

LINE

PHONE

geprufte

Sicherheit

R

LR92997

TM

TUY

PRODUCT SERVICE

Phone Filter

P/N 0802-3392-00

Made in China / Fabriquè China

Bel Fuse Inc. 1198

ACCESSARY

L.T.E. EQUIPMENT

E100296

99-16406

LINE

PHONE

99-16410

g

e

p

r

u

f

t

e

S

i

c

h

e

r

h

e

i

t

R

LR92997

T

M

TUY

PRODUCT SERVICE

Phone Filter

P

/N

0

8

0

2

-3

3

9

2

-0

0

M

a

d

e

in

C

h

in

a

/ F

a

b

r

iq

u

è

C

h

in

a

B

e

l F

u

s

e

I

n

c

. 1

1

9

8

A

C

E

S

A

R

Y

L

.T

.E

.

E

Q

U

IP

M

E

N

T

E

1

0

2

9

6

TM

TST

LINE

A

LMPW

R

ETH

ER

N

ET

T

M

T

M

B

A

S

E

P

H

O

N

E

TM

Quick Installation

Installation

Instructions

4

5

Installation

Before you install your SuperLine IAD, read the

Additional Notes on SuperLine IAD

Operation

on page 32, and the

Important Safety Instructions

on page 33.

Choose the procedure that sounds most like what you want to do:

H Add a Second Phone Line Page 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

This procedure describes how to add a new line for a phone.

H Add a Second Line for a Modem Page 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

This procedure describes how to add a new line for a modem.

H Work at Home Page 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

This procedure describes how to add new lines for a modem and an additional

phone.

H Home Office Page 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

This procedure describes how to connect an additional phone, fax machine, and

Ethernet-ready PC to your SuperLine IAD.

H Connect Phone Filters to Your Existing Phones Page 14. . . . . . . . . . . . . . . . . .

This procedure describes how to connect a phone filter to your existing phones.

H Connect a 2-Line Phone to the Existing

and Additional Phone Line Page 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

This procedure describes how to connect a 2-line, 2-cord phone to your SuperLine

IAD.

H Connect a 2-Line Phone to Two Additional Phone Lines Page 18. . . . . . . . . .

This procedure describes how to connect a 2-line, 1-cord phone to your SuperLine

IAD if you have ordered two additional lines.

H Use an Additional Phone Line in Other Rooms Page 20. . . . . . . . . . . . . . . . . . .

This procedure describes how to connect multiple phones, fax machines, or

modems in separate rooms. This configuration may not be applicable in all homes

or small offices.

H Connect to High-Speed Data Service Page 22. . . . . . . . . . . . . . . . . . . . . . . . . . . .

This procedure describes how to connect your SuperLine IAD to a PC or hub for

high-speed Internet services using the Ethernet port.

6

Add a Second Phone Line

Use the following procedure and supporting figure to add a new phone line.

Cables Required (Supplied)

H 6-foot phone cable (RJ11).

Cables Required (Not Supplied)

Obtain the following from your local electronics or phone store if they are not provided

with other equipment you have bought.

H Existing phone cables.

" Procedure

Connect the SuperLine IAD:

 Plug one end of the supplied phone cable into the LINE jack on the SuperLine IAD

rear panel.

 Plug the other end of the cable into the wall jack.

Add a Second Phone Line:

 Connect a phone to the PHONE 1/2 jack on the SuperLine IAD rear panel.

Connect the Existing Phone Line:

 If you wish to have your existing phone line available in this location, connect your

existing phone to the BASE PHONE jack on the SuperLine IAD rear panel.

Connect the ac power transformer:

 Insert the power cord’s cylindrical plug into the jack labeled POWER on the

SuperLine IAD rear panel. Plug the transformer into an ac power outlet.

Complete the Installation:

 Attach phone filters to all your other existing phones. Refer to

Connect Phone

Filters to Your Existing Phones

on page 14.

Your SuperLine IAD installation is now complete.

7

Additional

Phone

Phone 1/2

Base

Phone

Line

Wall

Jack

Existing

Phone

99-16430

Power

Adding a Second Line for a Phone

8

Add a Second Line for a Modem

Use the following procedure and supporting figure to connect a modem to your

SuperLine IAD.

Cables Required (Supplied)

H 6-foot phone cable (RJ11).

Cables Required (Not Supplied)

Obtain the following from your local electronics or phone store if they are not provided

with other equipment you have bought.

H Existing phone cables.

" Procedure

Connect the SuperLine IAD:

 Plug one end of the supplied phone cable into the LINE jack on the SuperLine IAD

rear panel.

 Plug the other end of the cable into the wall jack.

Connect the Modem:

 Connect the output of your modem to the PHONE 1/2 jack on the SuperLine IAD

rear panel.

Connect the Existing Phone Line:

 If you wish to have your existing phone line available in this location, connect your

existing phone to the BASE PHONE jack on the SuperLine IAD rear panel.

Connect the AC Power Transformer:

 Insert the power cord’s cylindrical plug into the jack labeled POWER on the

SuperLine IAD rear panel. Plug the transformer into an ac power outlet.

Complete the Installation:

 Attach phone filters to all your other existing phones. Refer to

Connect Phone

Filters to Your Existing Phones

on page 14.

Your SuperLine IAD installation is now complete.

9

99-16066-03

Phone 1/2

Base Phone

Wall

Jack

Line

Existing

Phone

Fax/Data

Modem

Power

Adding a Second Line for a Modem

10

Work At Home: Add New Lines

for a Modem and an Additional Phone

Use the following procedure and supporting figure to connect a modem and an extra

phone to your SuperLine IAD. You must have ordered two additional lines.

Cables Required (Supplied)

H 6-foot phone cable (RJ11).

Cables Required (Not Supplied)

Obtain the following from your local electronics or phone store if they are not provided

with other equipment you have bought.

H Existing phone cables.

" Procedure

Connect the SuperLine IAD:

¶ Plug one end of the supplied phone cable into the LINE jack on the SuperLine IAD

rear panel.

· Plug the other end of the cable into the wall jack.

Connect the Modem:

¸ Connect the output of your modem to the PHONE 1/2 jack on the SuperLine IAD

rear panel.

Connect the Additional Phone:

¹ Connect a phone to the PHONE 2 jack on the SuperLine IAD rear panel.

Connect the Existing Phone Line:

º If you wish to have your existing phone line available in this location, connect your

existing phone to the BASE PHONE jack on the SuperLine IAD rear panel.

Connect the AC Power Transformer:

» Insert the power cord’s cylindrical plug into the jack labeled POWER on the

SuperLine IAD rear panel. Plug the transformer into an ac power outlet.

11

Complete the Installation:

 Attach phone filters to all your other existing phones. Refer to

Connect Phone

Filters to Your Existing Phones

on page 14.

Your SuperLine IAD installation is now complete.

99-16434

Phone 1/2

Base Phone

Wall

Jack

Line

Existing

Phone

Fax/Data

Modem

Phone 2

Additional

Phone

Power

Connecting a Modem and an Additional Phone

12

Home Office: Add High-Speed Data Service,

a Fax Machine, and an Additional Phone

Use the following procedure and supporting figure to connect an Ethernet-ready PC,

fax machine, and additional phone to your SuperLine IAD in the same room. You must

have ordered two additional lines and Ethernet data service.

Cables Required (Supplied)

H 6-foot phone cable (RJ11).

Cables Required (Not Supplied)

Obtain the following from your local electronics or phone store if they are not provided

with other equipment you have bought.

H 8-pin Ethernet crossover cable.

H Existing phone cables.

" Procedure

Connect the SuperLine IAD:

¶ Plug one end of the supplied phone cable into the LINE jack on the SuperLine IAD

rear panel.

· Plug the other end of the cable into the wall jack.

Connect to High-Speed Data Service:

¸ Connect the network interface card of your PC to the ETHERNET jack on the

SuperLine IAD rear panel with a crossover cable. (If you are connecting to a hub,

you need a straight-through Ethernet cable. See

High-Speed Data Service

on

page 22.)

Connect the Fax Machine:

¹ Connect a fax machine to the PHONE 1/2 jack on the SuperLine IAD rear panel.

Connect the Additional Phone:

º Connect a phone to the PHONE 2 jack on the SuperLine IAD rear panel.

Connect the Existing Phone Line:

» If you wish to have your existing phone line available in this location, connect your

existing phone to the BASE PHONE jack on the SuperLine IAD rear panel.

13

Connect the AC Power Transformer:

 Insert the power cord’s cylindrical plug into the jack labeled POWER on the

SuperLine IAD rear panel. Plug the transformer into an ac power outlet.

Complete the Installation:

 Attach phone filters to all your other existing phones. Refer to

Connect Phone

Filters to Your Existing Phones

on page 14.

Your SuperLine IAD installation is now complete.

Fax

Machine

Phone 2

Phone 1/2

Base

Phone

Line

99-16433

Ethernet

Existing

Phone

PC with

Network

Interface

Card

Additional

Phone

Wall

Jack

Power

Adding High-Speed Data Service, a Fax Machine,

and an Additional Phone

14

Connect Phone Filters to Your Existing Phones

After you have installed your SuperLine IAD, each phone elsewhere in your home or

office that is connected to the same line as the SuperLine IAD must be connected

through a phone filter to minimize background noise from the additional lines.

Hardware Required (Not Supplied)

You may need to obtain additional phone filters from your service provider. One filter is

supplied with your SuperLine IAD.

" Procedure

Use the following procedure to install phone filters on your existing phones.

 Disconnect the phone cord of your existing phone from the wall jack.

 Plug the phone cord into the PHONE jack on the phone filter.

 Plug the phone filter into the wall jack.

Repeat Steps 1–3 for each phone in your home or office that is not directly connected

to your SuperLine IAD.

15

LINE

PHONE

99-16210-01

g

e

p

ru

fte

S

ic

h

e

rh

e

it

R

LR92997

TM

TUY

PRODUCT SERVICE

Phone Filter

P/N 0802-3392-00

Made in China / Fabriquè China

Bel Fuse Inc. 1198

ACCESSARY

L.T.E. EQUIPMENT

E100296

Installing a Phone Filter

16

Connect a 2-Line Phone to the Existing

and Additional Phone Line

Use the following procedure and supporting figure to connect your SuperLine IAD to a

single phone with two lines. This configuration can be used if you have one or two

additional phone lines through your SuperLine IAD.

Cables Required (Supplied)

H 6-foot phone cable (RJ11).

Cables Required (Not Supplied)

Obtain the following from your local electronics or phone store if they are not provided

with other equipment you have bought.

H Existing phone cables.

" Procedure

Connect the SuperLine IAD:

 Plug one end of the supplied phone cable into the LINE jack on the SuperLine IAD

rear panel.

 Plug the other end of the cable into the wall jack.

Connect Line 1:

 Connect Line 1 of your 2-line phone to the BASE PHONE jack on the SuperLine

IAD rear panel.

Connect Line 2:

 Connect Line 2 of the 2-line phone to the PHONE 1/2 jack on the rear of the

SuperLine IAD.

Connect the AC Power Transformer:

 Insert the power cord’s cylindrical plug into the jack labeled POWER on the

SuperLine IAD rear panel. Plug the transformer into an ac power outlet.

17

Complete the Installation:

 Attach phone filters to all your other existing phones. Refer to

Connect Phone

Filters to Your Existing Phones

on page 14.

Your SuperLine IAD installation is now complete.

99-16100-03

Phone 1/2

Base Phone

Line 2

Line 1

2-Line

Phone

Wall

Jack

Line

Power

Connecting a 2-Line Phone (with One or Two Additional Lines)

18

Connect a 2-Line Phone to Two Additional Phone Lines

Use the following procedure and supporting figure to connect your SuperLine IAD to a

single phone with two lines. Use this configuration only if you have two additional phone

lines through your SuperLine IAD.

Cables Required (Supplied)

H 6-foot phone cable (RJ11).

Cables Required (Not Supplied)

Obtain the following from your local electronics or phone store if it is not provided with

other equipment you have bought.

H A 2-line phone cable (RJ14C) to connect Lines 1 and 2 of your 2-line phone to your

SuperLine IAD. Refer to

Technical Information

on page 23 for more information.

" Procedure

Connect the SuperLine IAD:

 Plug one end of the supplied phone cable into the LINE jack on the SuperLine IAD

rear panel.

 Plug the other end of the cable into the wall jack.

Connect Lines 1 and 2:

 Connect your 2-line phone using your 2-line RJ14C phone cable to the PHONE 1/2

jack on the SuperLine IAD rear panel. The 2-line phone cable connects both lines

through the PHONE 1/2 jack.

Connect the AC Power Transformer:

 Insert the power cord’s cylindrical plug into the jack labeled POWER on the

SuperLine IAD rear panel. Plug the transformer into an ac power outlet.

Complete the Installation:

 Attach phone filters to all your other existing phones. Refer to

Connect Phone

Filters to Your Existing Phones

on page 14.

Your SuperLine IAD installation is now complete.

19

99-16036a-03

Phone 1/2

RJ14

Phone

Cable

2-Line

Phone

Wall

Jack

Line

Phone 2

(not used in

this configuration)

Connecting a 2-Line Phone to Two Additional Lines

20

Use an Additional Phone Line in Other Rooms

If your home or office phone jacks are wired internally with 4 wires, you may be able to

connect phones in other rooms to your SuperLine IAD by using optional hardware

purchased from your local electronics or phone store. If you are unsure if your home or

office is wired with 4 wires, contact an electrician or your service provider.

Cables Required (Supplied)

H 6-foot phone cable (RJ11).

Cables and Hardware Required (Not Supplied)

You may need to obtain additional phone filters from your service provider. One filter is

supplied with your SuperLine IAD. Obtain the following from your local electronics or

phone store if they are not provided with other equipment you have bought.

H “T” type connectors. Refer to

“T” Type Connector

on page 30 for “T” type connector

specifications.

H RJ11 phone cables to connect the SuperLine IAD to the “T” type connector and

your existing phone to the SuperLine IAD.

" Procedure

Use the following procedure and supporting figure to install your SuperLine IAD with

multiple phones, fax machines, or modems connected in other rooms.

Connect the SuperLine IAD:

¶ Plug a “T” type connector into the wall jack of the room where the SuperLine IAD is

located.

· Plug one end of the supplied phone cable into the LINE jack on the SuperLine IAD

rear panel.

¸ Plug the other end of the cable into Line 1 of the “T” type connector.

¹ Plug a phone cable into Line 2 of the “T” type connector.

º Plug the other end of the cable into the PHONE 1/2 jack on the SuperLine IAD rear

panel.

» If applicable, connect an additional phone, fax machine, or modem into the

PHONE 2 jack on the SuperLine IAD rear panel using one of your existing cables.

Connect a Phone, Fax Machine, or Modem In Another Room:

¼ Plug a second “T” type connector into the wall jack of another room.

½ Connect the additional phone, fax machine, or modem to Line 2 of the “T” type

connector. You can connect a phone to your existing phone line using Line 1 of the

“T” type connector and a phone filter as shown.

Repeat Steps 7 and 8 for any additional rooms you want to connect.

Connect the AC Power Transformer:

¾ Insert the power cord’s cylindrical plug into the jack labeled POWER on the

SuperLine IAD rear panel. Plug the transformer into an ac power outlet.

Page is loading ...

Paradyne 6512-A2 Installation Instructions Manual

Paradyne 6512-A2 Installation Instructions Manual

in other languages

Related papers

Other documents