Paradyne SuperLine 6040 Installation Instructions Manual

Brand: Paradyne

Model: SuperLine 6040

Type: Installation Instructions Manual

This manual is also suitable for

Hotwire 6040

Paradyne SuperLine 6040 is a Wall Jack Filter designed to isolate the voice frequency range from the SuperLine signal, allowing phones and other devices to use the same line as the SuperLine Integrated Access Device (IAD).

Key features and benefits of the Paradyne SuperLine 6040 include:

Easy installation: The filter can be installed in 4-wire series, 4-wire star, and 2-wire configurations, making it suitable for a variety of applications.
Improved signal quality: The filter helps to improve the quality of voice and data transmissions by isolating the voice frequency range from the SuperLine signal.

Key features and benefits of the Paradyne SuperLine 6040 include:

Easy installation: The filter can be installed in 4-wire series, 4-wire star, and 2-wire configurations, making it suitable for a variety of applications.
Improved signal quality: The filter helps to improve the quality of voice and data transmissions by isolating the voice frequency range from the SuperLine signal.

SuperLine



6040 Wall Jack Filter

Installation Instructions

Document Number 6040-A2-GN10-00

September 1999

SuperLine 6040 Wall Jack Filter

Phones and other devices using the same line as the SuperLine Integrated Access

Device (IAD) require a filter to isolate the voice frequency range from the SuperLine

signal.

Basic Configurations

4-Wire Series

The SuperLine 6040 Wall Jack Filter replaces the first wall jack in a 4-wire series

configuration.

3, 4

2, 5

SuperLine 6040

Wall Jack Filter

Line 1 Filtered

Line 2 Unfiltered

NID

99-16545

Filter Installation In a 4-Wire Series Configuration

4-Wire Star

The SuperLine 6040 Wall Jack Filter replaces all wall jacks in a 4-wire star configuration

(where each wall jack is wired individually to the NID).

3, 4

2, 5

All Jacks

Replaced

with Filters

NID

99-16546

3, 4

2, 5

3, 4

2, 5

Filter Installation In a 4-Wire Star Configuration

2-Wire Configuration

You may need to run new wiring to the location of the SuperLine IAD in a 2-wire

configuration.

NID

3, 4

SuperLine 6040

Wall Jack Filter

Filtered

Unfiltered

99-16547

3, 4

Standard Jack

Added for

SuperLine IAD

New Wiring

Added for

SuperLine IAD

Filter Installation In a 2-Wire Configuration

Product-Related Documents

For information about the SuperLine IAD, refer to

SuperLine IAD, Models 6501, 6502,

6510, 6511, and 6512, Installation Instructions

, Document Number 6500-A2-GN10.

To request a paper copy of a Paradyne document:

H Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)

H Outside the U.S.A., call 1-727-530-8623

Paradyne documents are also available on the World Wide Web at

www.paradyne.com. Select

Library

→

Technical Manuals

Equipment Required

H SuperLine 6040 Wall Jack Filter (one or more required)

H Single-pair or multi-pair wire (if adding a new wall jack for the SuperLine IAD)

H 2-line splitter (if not adding a new wall jack for the SuperLine IAD)

Tools Required

H Tone generator and probe, or power source and continuity tester

H Phillips screwdriver

H Flat-blade screwdriver

H Wire cutter

H Wire stripper

Installation Checklist

Installation of the SuperLine 6040 Wall Jack Filter consists of the following steps:

Disconnect the customer premises wiring from the local loop.

Determine whether wall jacks are wired in series or individually.

Replace wall jacks with SuperLine 6040 Wall Jack Filters as required.

Install new wiring (2-wire system) or a 2-line splitter (4-wire system) for the

SuperLine IAD.

If the customer premises has four wires, join the two pairs at the NID.

Reconnect the customer premises wiring to the local loop.

Procedures for each step are on the following pages.

Installation

1. Disconnect the Line

At the NID (Network Interface Device) or first accessible entry point, disconnect the

customer premises wiring from the local loop.

WARNING:

Do not continue unless the line has been disconnected. Refer to

Important Safety Instructions,

page 13.

2. Determine Wiring Arrangement

Use a tone generator or continuity tester to determine whether wall jacks are wired in a

series or star configuration.

H If wall jacks are wired in series, trace the wiring and use the tone generator or

continuity tester to determine which is the first wall jack wired to the line’s

origination at the NID or other entry point. You must replace that wall jack with a

Wall Jack Filter.

H If some or all wall jacks are wired in a star configuration (that is, more than one wall

jack is wired directly to the NID or other entry point), you must replace every such

wall jack.

Use the following table to select the proper procedures for installation.

Customer Premises

Configuration

Procedures to Use If

NID Accessible

Procedures to Use If

NID Not Accessible

2-Wire Series 3A, 4A 3B, 4A or 4B*

2-Wire Star 3B, 4B 3B, 4B

4-Wire Star or Series 3A, 4B 3B, 4B

6-Wire Star or Series 3A, 4B 3B, 4B

* Replace the wall jack nearest the NID with a Wall Jack Filter. If the SuperLine IAD

will not be used at that location, treat the Wall Jack Filter as a NID and run new

(unfiltered) wiring for the SuperLine IAD from the filter input connections.

3A. Replace the Wall Jack with a Filter – NID Accessible

If the NID is not accessible, or the customer premises configuration is a 2-wire star,

proceed to

Replace the Wall Jack with a Filter – NID Not Accessible, or 2-Wire

page 8.

Use the following procedure to install a SuperLine 6040 Wall Jack Filter when the NID is

accessible. When this procedure is complete, filtering is provided on Pins 3 and 4 and

SuperLine service is provided on Pins 2 and 5 of all wall jacks.

" Procedure

1. Remove the existing wall jack and disconnect the wires from it. Note which wire

bundle runs to the NID and which one runs to the next wall jack.

2. If the wire ends are damaged, clip off the damaged portion. Strip the wires to

expose 1/4I of bare copper.

3. Remove the four screws from the faceplate of the filter and set aside the faceplate.

4. Connect the wires to the screw terminals on the filter assembly:

Screw Term

nal On

Customer Premises Wiring (If Present)

crew

erm

Wall Jack Filter

Line Pin

Green or White/Blue from NID FILTER IN – TIP 1 3

Red or Blue/White from NID FILTER IN – RING 1 4

Green or White/Blue to next jack FILTER OUT – TIP 1 3

Red or Blue/White to next jack FILTER OUT – RING 1 4

Black or White/Orange both from NID and

to next jack

TIP 2 2 2

Yellow or Orange/White both from NID and

to next jack

RING 2 2 5

White or White/Green both from NID and to

next jack

TIP 3 3 1

Blue or Green/White both from NID and to

next jack

RING 3 3 6

TIP

RING

TIP 2

RING 2

TIP 3

RING 3

TIP

RING

FILTER IN

FILTER OUT

To NID

To Next

Jack

(If any)

99-16548

5. Fasten the filter assembly to the wall box using the screws that held the old wall

jack. An engraving on the filter assembly (UP↑) shows the proper orientation.

6. Fasten the faceplate to the filter assembly.

If any other wall jacks are wired individually to the NID (see

Determine Wiring

Arrangement

on page 5), repeat the procedure for all wall jacks.

3B. Replace the Wall Jack with a Filter – NID Not Accessible, or 2-Wire

If the configuration is not 2-wire and the NID is accessible, go to

3A. Replace the Wall

Jack with a Filter – NID Accessible

on page 6.

Use the following procedure to install a SuperLine 6040 Wall Jack Filter when the NID is

not accessible or the customer premises configuration is 2-wire. When this procedure is

complete, filtering is provided on Pins 3 and 4 and SuperLine service is provided on

Pins 2 and 5 of all wall jacks.

For a 2-wire series configuration, replace the wall jack nearest the NID with a Wall Jack

Filter and install the SuperLine IAD there. If the SuperLine IAD must be installed

elsewhere, run new wiring to a standard wall jack from the FILTER IN – TIP and RING

connections of the filter to the new wall jack.

" Procedure

1. Locate the first wall jack connected to the NID.

2. Remove the existing wall jack and disconnect the wires from it. Note which wire

bundle runs to the NID and which one runs to the next wall jack.

3. If the wire ends are damaged, clip off the damaged portion. Strip the wires to

expose 1/4I of bare copper.

4. Remove the four screws from the faceplate of the filter and set aside the faceplate.

5. On the filter assembly:

— Remove the wire from TIP 2 and fasten it to FILTER IN – TIP

— Remove the wire from RING 2 and fasten it to FILTER IN – RING

TIP

RING

TIP 2

RING 2

FILTER IN

99-16549

6. Connect the wires to the screw terminals on the filter:

Screw Term

nal On

Customer Premises Wiring (If Present)

crew

erm

Wall Jack Filter

Line Pin

Green or White/Blue from NID FILTER IN – TIP 1 3

Red or Blue/White from NID FILTER IN – RING 1 4

Green or White/Blue to next jack FILTER OUT – TIP 1 3

Red or Blue/White to next jack FILTER OUT – RING 1 4

Black or White/Orange to next jack FILTER IN – TIP 2 2

Yellow or Orange/White to next jack FILTER IN – RING 2 5

White or White/Green both from NID and to

next jack

TIP 3 3 1

Blue or Green/White both from NID and to

next jack

RING 3 3 6

TIP

RING

TIP 2

RING 2

TIP 3

RING 3

TIP

RING

FILTER IN

FILTER OUT

To NID

To Next

Jack

(If any)

99-16550

7. Fasten the filter assembly to the wall box using the screws that held the old wall

jack. An engraving on the filter assembly (UP↑) shows the proper orientation.

8. Fasten the faceplate to the filter assembly.

4A. Prepare a Wall Jack for the SuperLine IAD – 2-Wire

Preparation for the SuperLine IAD depends on whether the customer premises is wired

with two wires or four.

Use the following procedure to prepare a wall jack for the SuperLine IAD in a 2-wire

configuration.

" Procedure

1. Determine where the customer wants the SuperLine IAD installed.

2. Run new wiring from the NID or other entry point to the point where the SuperLine

IAD will be located.

3. Install a standard wall jack and connect the new wiring to the Pin 3 and Pin 4

positions.

4. Use the phone cord supplied with the SuperLine IAD to connect the LINE jack of

the SuperLine IAD to the new wall jack. No 2-line splitter is required for this type of

installation.

5. At the NID, reconnect the line to the local loop.

NID

3, 4

SuperLine 6040

Wall Jack Filter

Filtered

99-16551

3, 4

Standard Jack

Added for

SuperLine IAD

New Wiring

Added for

SuperLine IAD

LINE Jack

TST

LINE

ALM

PWR

ETHERNET

SuperLine IAD Installation In a 2-Wire Configuration

4B. Prepare a Wall Jack for the SuperLine IAD – 4-Wire

Use the following procedure to prepare a wall jack for the SuperLine IAD in a 4-wire

configuration.

" Procedure

1. Determine where the customer wants the SuperLine IAD installed.

2. Plug a 2-line splitter into the wall jack at that location.

3. Use the phone cord supplied with the SuperLine IAD to connect the LINE jack of

the SuperLine IAD to the Line 2 jack of the 2-line splitter.

99-16552

Line 1

Line 2

LINE Jack

2-Line

Splitter

TST

LINE

ALMPWR

ETHERNET

SuperLine IAD Installation In a 4-Wire Configuration

4. At the NID:

— Join the Tip wire of Line 1 (green or white/blue) and the Tip wire of Line 2

(black or white/orange).

— Join the Ring wire of Line 1 (red or blue/white) and the Ring wire of Line 2

(yellow or orange/white).

— Reconnect the line to the local loop.

3, 4

2, 5

Line 1

Line 2

NID

99-16553

Line 1

Important Safety Instructions

1. Read and follow all warning notices and instructions marked on the product or

included in the manual.

2. This product is intended to be connected to Listed/Certified telephone wiring with a

minimum of 24 AWG (.5 mm) behind a Listed/Certified primary protector.

3. Do not attempt to install or service this product yourself, as opening or removing

covers may expose you to dangerous high-voltage points or other risks. Refer all

installation and servicing to qualified service personnel.

4. When installed in the final configuration, the product must comply with the

applicable Safety Standards and regulatory requirements of the country in which it

is installed. If necessary, consult with the appropriate regulatory agencies and

inspection authorities to ensure compliance.

5. In addition, since the equipment is to be used with telecommunications circuits,

take the following precautions:

— Never install telephone wiring during a lightning storm.

— Never install telephone jacks in wet locations unless the jack is specifically

designed for wet locations.

— Never touch uninsulated telephone wires or terminals unless the telephone

line has been disconnected at the network interface.

— Use caution when installing or modifying telephone lines.

— Avoid using a telephone (other than a cordless type) during an electrical storm.

There may be a remote risk of electric shock from lightning.

— Do not use the telephone to report a gas leak in the vicinity of the leak.

Notice to Users of the Telephone Network

This equipment complies with Part 68 of the FCC rules. On the inside of the wall plate is

a label that contains, among other information, the FCC registration number and ringer

equivalence number (REN) for this equipment. If requested, this information must be

provided to the telephone company.

This equipment is intended to be hard wired to the telephone line’s primary protector

and to the inside building wiring. The 6-position modular wall jack is designed to be

connected to compatible modular plugs which are Part 68 compliant.

The REN is used to determine the quantity of devices which may be connected to the

telephone line. Excessive RENs on the telephone line may result in the devices not

ringing in response to an incoming call. In most, but not all areas, the sum of RENs

should not exceed five (5.0). To be certain of the number of devices that may be

connected to a line, as determined by the total RENs, contact the local telephone

company.

If the Wall Jack Filter causes harm to the telephone network, the telephone company

will notify you in advance that temporary discontinuance of service may be required. But

if advance notice is not practical, the telephone company will notify the customer as

soon as possible. Also, you will be advised of your right to file a complaint with the FCC

if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or

procedures that could affect the operation of the equipment. If this happens, the

telephone company will provide advance notice in order for you to make necessary

modifications to maintain uninterrupted service.

If trouble is experienced with the Telephone Line Filter, for repair or warranty

information, please refer to

Warranty, Sales, Service, and Training Information

No repairs may be performed by the end user.

The equipment can not be used on public coin phone service provided by the

telephone company. Connection to party line service is subject to state tariffs. Contact

the state public utility commission, public service commission or corporation

commission for information.

Warranty, Sales, Service, and Training Information

Contact your SuperLine service provider directly for any help needed. For additional

information concerning warranty, sales, service, repair, installation, documentation,

training, distributor locations, or Paradyne worldwide office locations, use one of the

following methods:

H Internet: Visit the Paradyne World Wide Web site at www.paradyne.com.

(Be sure to register your warranty at www.paradyne.com/warranty.)

H Telephone: Call our automated system to receive current information by fax or to

speak with a company representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A., call 1-727-530-2340

Document Feedback

We welcome your comments and suggestions about this document. Please mail them

to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773,

or send e-mail to [email protected]. Include the number and title of this

document in your correspondence. Please include your name and phone number if you

are willing to provide additional clarification.

Paradyne SuperLine 6040 Installation Instructions Manual

Brand: Paradyne

Model: SuperLine 6040

Type: Installation Instructions Manual

This manual is also suitable for

Hotwire 6040

Key features and benefits of the Paradyne SuperLine 6040 include:

Easy installation: The filter can be installed in 4-wire series, 4-wire star, and 2-wire configurations, making it suitable for a variety of applications.
Improved signal quality: The filter helps to improve the quality of voice and data transmissions by isolating the voice frequency range from the SuperLine signal.

Download PDF

report

Paradyne SuperLine 6040 Installation Instructions Manual

This manual is also suitable for

Paradyne SuperLine 6040 Installation Instructions Manual

Related papers

Other documents