Infinity Interlude IL120s User manual

Brand: Infinity

Model: Interlude IL120s

Category: Subwoofers

Type: User manual

This manual is also suitable for

Interlude Series

Interlude Series

IL120s Subwoofer

Service Manual

Infinity Systems, Inc

250 Crossways Park Dr.

Woodbury, New York 11797

REV 1 10/2001

IL120s

CONTENTS

SPECIFICATIONS …….…………………………….………………….3

DETAILED SPECIFICATIONS ……………………..…………………4

CONTROLS and CONNECTIONS ………………….….….…………6

OPERATION……………………………………..……..…..…….……..8

BASS OPTIMIZATION SYSTEM…………….………….….…………9

MECHANICAL/PACKING PARTS LIST………………..……………11

EXPLODED VIEW ……………………………………….……………12

PACKAGING …………………………….………………………….…13

EXPLODED VIEW OF AMPLIFIER…………………….……………14

TEST SETUP and PROCEDURE……………….……..……………15

IL120s ADJUST BIAS PROCEDURE………………..…………………16

PRINTED CIRCUIT BOARD DIAGRAMS………………..…………17

ELECTRICAL PARTS LIST (120v)…………………….….…………23

INTEGRATED CIRCUIT DIAGRAMS ………………………………31

IL120s SCHEMATICS…………..……….……………………………32

IL120s

SPECIFICATIONS

IL120s Frequency Response: 28Hz - 150Hz (±3dB)

Maximum Amplifier Output: 500 watts (20Hz - 150Hz with no more than 0.1% THD)

Crossover Frequencies: 50Hz - 150Hz, 24dB/octave, continuously variable

Driver: 12" C.M.M.D.

Dimensions (H x W x D): 17-1/2" x 17-1/4" x 19-3/4"

Weight: 45 lb (20.5kg)

Optional Accessory: Bass Optimization

Test & Measurement Kit:

Part Number: 335852-002

DETAILED SPECIFICATIONS

IL120s

DETAILED SPECIFICATIONS (Cont.)

IL120s

CONTROL and CONNECTIONS

IL120s

CONNECTIONS

IL120s

OPERATION

IL120s

BASS OPTIMIZATION SYSTEM

IL120s

BASS OPTIMIZATION SYSTEM

(Cont.)

plays the tones from the test CD and records the relative output level of each test tone, using the sound-level meter,

on the provided measurement template. After all the tones are complete, the template contains a response curve

for the frequencies below 100Hz. The user simply notes the frequency of the largest bass peak, calculates the cor-

rect amount of attenuation, and uses the “Q-Finder” to determine the width of the curve. These three values are

dialed into the Bass Optimization System controls located on the speaker. The entire process takes less than twen-

ty minutes.

If your dealer does not stock the Bass Optimization System test and measurement kit, you may purchase it directly

from Infinity. U.S. residents can visit our Web site at www.infinitysystems.com or call 1-800-553-3332. Canadian

residents should contact their dealer or call 1-800-567-3275.

Ask for Infinity part number 335852-002.

IL120s

MECHANICAL/PACKAGING PARTS LIST

MECHANICAL

IL120s COMPLETE AMPLIFIER ASSY N/A

WOOFER, 12”, C.M.M.D., shielded, 3.4 ohms ±10% 336056-001

VOLUME CONTROL, R-IL 336250-001

FRONT BAFFLE 336439-001

PORT TUBE 336799-001

GRILLE CUP (12) 333249-003

GRILLE, GRAY 336441-001

GRILLE, MIDNIGHT BLUE 336441-002

GRILLE, RICH BURGUNDY 336441-003

GRILLE, BLACK 336441-004

PACKAGING

OWNER’S MANUAL, IL100S/IL120S 335839-001

WARRANTY CARD 335841-001

SURVEY CARD 330033-001

CARTON 336497-001

FOOT (4) 334186-002

FOOT PAD (4) 334192-001

PAD, END, TOP 336496-001

PAD, END, BOTTOM 336496-002

GRILLE ASSEMBLY See Options Above

POWER CORD, 120V US-15’ 336658-115

RABOS SCREW DRIVER 335848-002

Description Part Number

IL120s

EXPLODED VIEW

CABINET

(NOT FOR SALE)

WOOFER, 12"

(336056-001)

VOLUME CONTROL, R-IL

(336250-001)

FRONT BAFFLE

(336439-001)

PORT TUBE

(336799-001)

GRILLE CUP (6)

(333249-003)

GRILLE CUP (6)

(333249-003)

GRILLE, GRAY 336441-001

GRILLE, MIDNIGHT BLUE 336441-002

GRILLE, RICH BURGUNDY 336441-003

GRILLE, BLACK 336441-004

FOOT (4)

(334186-002)

FOOT PAD (4)

(334192-001)

OO514

IL120s

AMPLIFIER ASSY

(NOT FOR SALE)

TO SERVICE THE IL120s SUBWOOFER

1) Remove the grille.

2) Extract (6) rubber grille retainers as shown in the illustration above, this can be accomplished by

carefully pulling them out of the cavities with long-nosed pliers or similar tool.

3) Remove the (6) Phillips screws that are now exposed.

4) Remove the front baffle.

5) Remove the (6) screws that secure the driver.

6) To service the amplifier, remove the (12) Phillips screws at the rear of the enclosure, and pull the

amplifier out of the back.

SCREW, (2)

#6 x .75, PB, PPH, BLK

(903401-012)

SCREW, (6)

#6 x .75, PB, PPH, BLK

(903401-012)

SCREW, (12)

#8 x .75, PB, PPH BLK

(900101-012)

SCREW, (6)

#8 x .75, PB, PPH BLK

(900101-012)

SCREW,

#8 x 1, PB TRPH BLK

(903101-016)

IL120s

PACKAGING

OWNER'S MANUAL

IL100S/IL120S

(335839-001)

WARRANTY CARD

(335841-001)

SURVEY

CARD

(330033-001)

POWER CORD,

120V US-15'

(336658-115)

RABOS SCREW

DRIVER

(335848-002)

GRILLE ASSEMBLY,

GRAY,

(336441-001)

PAD, END, TOP

(336496-001)

PAD, END, BOTTOM

(336496-002)

CARTON

(336497-001)

00513

IL120s

EXPLODED VIEW OF AMPLIFIER

LINEAR

BOARD

FEATURE

BOARD

RABOS

BOARD

POWER

SUPPLY

BOARD

RCA

QUADJACK

(JC0052)

SWITCH, (4)

SPDT TOGGLE

(SR0007)

BINDING

POSTS GOLD

(JC0104)

FUSE HOLDER

PANEL MT SEALED

(FH0012)

FUSE, 4A 250V

1.25X.25 SLO-BLO

(FS0026)

AC (120V)

IEC SOCKET

(JC0129)

SWITCH,

ROCKER POWER

(SR0032)

FRONT VIEW

EMI

BOARD

00515

IL120s

TEST SETUP and PROCEDURE

00516

SIGNAL

GENERATOR

AMPLIFIER

AC VOLT

METER (10V)

IL120s

UNDER TEST

OUTPUT

FROM

GENERATOR/AMPLIFIER

00345

SYSTEM AURAL SWEEP TEST

Equipment needed:

• Function/signal generator/sweep generator

• Integrated Amplifier

• Multimeter

• Speaker cables

General Unit Function (UUT = Unit Under Test)

Switches/knobs on the amplifier faceplate:

Input Select to “Line”

Low Pass Filter to OFF

Bass Optimization system to OFF

Low Pass Frequency Adjust full CW (150Hz)

Phase switch – either position

1. From the signal generator, Connect both right and left line level inputs (RCA) to signal generator and UUT. Use Y-cable if

necessary from mono source.

2. On the front of the unit, turn the LEVEL control full clockwise (0).

3. Turn on generator, adjust to 120mV, 30 Hz.

4. Plug in UUT; turn the power switch ON. LED should be Red. Turn LEVEL control full counterclockwise (10)

5. LED should now be Green; immediate bass response should be heard and felt from rear port tube opening.

6. Turn off generator, turn LEVEL control fully clockwise (0), disconnect RCA cable.

7. Connect one pair of speaker cables to Speaker Level input terminal on UUT. Cables should be connected to an integrated

amplifier fed by the signal generator.

8. Switch Input to “Speaker”.

9. Turn on generator and adjust so that speaker level input at the amplifier is 2.2V, 30 Hz. Turn LEVEL control full counter-

clockwise (10)

10. Green LED should light, immediate bass response should be heard and felt from the port tube opening.

Sweep Function

1. Follow steps 7-10 above, using a sweep generator as a signal source.

2. Sweep generator from 20Hz to 20kHz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If

any unusual noises are heard, remove woofer and test.

Driver Function (Woofer)

1. Remove woofer from cabinet; detach + and - wire clips. See page 12 for removal instructions.

2. Check DC resistance of woofer; it should be 3.4 ohms±10%.

3. Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal

generator. Turn on generator and adjust so that speaker level output is 5.0V.

4. Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.

IL120s ADJUST BIAS PROCEDURE

(Mandatory when any output MOSFET transistors Q3,4,7,8 are replaced)

1. Amplifier should be unplugged and OFF.

2. Remove Amp assembly from cabinet; remove rear plastic cover if present. All wires exiting

the cover can remain connected unless they will prevent you from removing the amplifier or

accessing potentiometers on the Linear board PCB in the following steps.

3. Locate the Linear board assembly (PCB with the output transistors)

4. Adjust R11 and R27 fully Counter Clockwise. See diagram below.

5. Apply 120 VAC power to unit, Turn power switch ON.

6. Verify LED illuminates on the front gain control dial unless you have disconnected the plug.

7. Connect voltmeter set to DC millivolt range to twin pins on terminal J7, on Linear board

8. Verify initial voltage is less then 0.1 mV.

9. Adjust R11 Clockwise until voltmeter reads 0.3 mV + the initial current from step #8.

10. Adjust R27 Clockwise until voltmeter now reads 0.6 mV + the initial current from step #8.

11. Turn amplifier OFF. Disconnect AC power to unit.

12. Remove voltmeter from terminal J7.

13. Replace cover (if present), wires if disconnected, and replace amplifier back into cabinet.

IL120s

IL VOLUME RIGHT BOARD

IL120s

EMI FILTER BOARD

IL120s

IL FEATURE BOARD

IL120s

IL RABOS BOARD

Page is loading ...

Infinity Interlude IL120s User manual

Brand: Infinity

Model: Interlude IL120s

Category: Subwoofers

Type: User manual

This manual is also suitable for

Interlude Series

Download PDF

report

Infinity Interlude IL120s User manual

This manual is also suitable for

Infinity Interlude IL120s User manual

Related papers

Other documents