2. Computers & electronics
  3. Audio & home theatre
  4. Loudspeakers
  5. JBL
  6. Control One
Control One

JBL Control One Technical Manual

  • Hello! I am an AI chatbot trained to assist you with the JBL Control One Technical Manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the nominal impedance of the JBL Control One speaker system?
    What is the maximum recommended amplifier power for the JBL Control One speaker system?
    What is the frequency response range of the JBL Control One speaker system?
    What is the sensitivity rating of the JBL Control One speaker system?
    What is the crossover frequency of the JBL Control One speaker system?
    What are the dimensions of the JBL Control One speaker system?
    What is the weight of the JBL Control One speaker system?
    What type of high-frequency transducer does the JBL Control One speaker system use?
    What is the DC resistance of the high-frequency transducer in the JBL Control One speaker system?
    What type of low-frequency transducer does the JBL Control One speaker system use?
ACOUSTIC & ELECTRICAL SPECIFICATIONS:
• Nominal Impedance 8 Ohms
• Max Amp Power 80 Watts*
• Frequency Response 80Hz – 20kHz
• Sensitivity 89dB (2.83V @ 1 meter)
• Crossover Frequency 4000Hz
SYSTEM COMPONENTS:
• Cabinet Control 1X/1Xtreme/One
(Not for Sale)
• Grille Black (C1004X)
Silver (C1004X-S)
• High-Frequency Transducer 1/2" (12.7mm) Titanium-
laminate, shielded (C1002X)
DC Resistance 3.3 Ohms, ±10%
• Low-Frequency Transducer 4" (101.6mm) Shielded
(C1003X)
DC Resistance 2.4 Ohms, ±10%
• Crossover Network (C1006X)
AURAL SWEEP TEST SPECIFICATIONS:
• System Aural Sweep Test 6.0V Input 80Hz to 20kHz
• L.F. Aural Sweep Test 5.0V Input 80Hz to 5kHz
• H.F. Aural Sweep Test 2.83V Input 3kHz to 20kHz
PHYSICAL SPECIFICATIONS:
• Enclosure Dimensions 9" x 6-1/16" x 5-7/16"
(228mm x 155mm x 139mm)
• Weight 10.4 lb/4.7kg (sold in pairs)
WARRANTY:
• Refer to Warranty Statement packed with each product.
* The maximum recommended amplifier power rating will
ensure proper system headroom to allow for occasional
peaks. We do not recommend sustained operation at these
maximum power levels.
Technical Manual
Control®1X/1Xtreme/One
Control®1X/1Xtreme/One
Wall Bracket
Control One – C10034A
Control One SI – C10034S
Customer-Reply Card
Beauty Carton
Control One – C10029A
Control One SI – C10029S
Control 1X – C1007X
Control 1Xtreme –
C10029X or C10031X
Control One C1008A
C1008X
Foamed PS
End Padding
(2)
Limited-Warranty Card
Owner’s manual
visit www.jbl.com
Harman Consumer Group, Inc., 250 Crossways Park Drive, Woodbury, New York 11797
5/08
CONTROL 1X/1XTREME/ONE SCHEMATIC
EVA Gasket
Black
C1006X
Crossover Network
Nut, M4x0.7Px3t
mm Zinc-Plated
Nut
M5x0.8mm
Zinc-Plated
Die-Cast Alum.
Safety Ring, Black
Spring
Washer
C1004X
Metal Grille, Black
C1004X-S
Metal Grille, Silver
Tweeter
Diffuser
Control 1X – C1005X
Control 1Xtreme – C10028X
Control One C10028A
Logo Badge
on Grille
Front Baffle
Black
Control 1X/1Xtreme/One
(NOT for SALE)
Grille Holding Ring
Black
C1003X
4-1/2" Woofer
C1002X
Tweeter
Screw
4x8mm
Black-Plated
Screw
T4x35mm
Black-Plated
Screw
3.5x10mm
Black-Plated
Screw
4x18mm
Black-Plated
Control®1X/1Xtreme/One
Technical Manual
Control®1X/1Xtreme/One
EXPLODED VIEW
Harman Consumer Group, Inc., 250 Crossways Park Drive, Woodbury, New York 11797
5/08
TO SERVICE THE CONTROL 1X/1XTREME/ONE
1. Remove the grille.
2. Remove all (6) 1-3/8" Allen-head screws holding the front baffle to the enclosure.
3. Separate the front baffle w/drivers from the enclosure.
DRIVER REMOVAL – Both woofer and tweeter are bonded to the front baffle with adhesive.
Unclip FASTON connectors from both woofer and tweeter.
a) Woofer removal:
Remove all (4) machine screws; rear nut can be held by long-nosed pliers while screws are turned.
Apply heat gun (750°) to area around woofer basket until adhesive softens enough to extract the woofer.
b) Tweeter removal:
Remove both (2) Phillips screws.
Apply heat gun (750°) to area around inside of cavity until adhesive softens enough to extract the tweeter.
After removal, take care not to lose or misplace the small clear plastic diffuser should it become dislodged.
CAUTION: Too much heat applied in one area too long could warp the front baffle.
DRIVER REPLACEMENT
Both woofer and tweeter must have a bead of adhesive applied to the outer rim only upon reassembly.
Silicone sealer or rubber-to-metal cement is recommended.
/