Gyration GPT6105 Start Here

Brand: Gyration

Model: GPT6105

Type: Start Here

Gyration GPT6105 is a wireless pointing device that uses motion-sensing technology to track the movements of your hand. This allows you to control the cursor on your computer screen without having to move the mouse itself. The GPT6105 is ideal for use in presentations, as it allows you to move around the room and still control the cursor. It is also great for use in gaming, as it provides a more immersive experience than a traditional mouse.

The GPT6105 is easy to set up and use. Simply plug the RF Receiver/Flash Drive into an available USB port on your computer and turn on the GPT6105. The two devices will automatically connect to each other.

START

HERE

Connect

Activation Button

Swipes Button

Flip Over

Back of

full-size

keyboard

Front of

compact

keyboard

RF Receiver/Flash Drive

Remove the RF Receiver/Flash Drive from

the bottom of the GYROTRANSPORT Air Mouse.

To open the battery compartment

on the front bottom of the

GYROTRANSPORT Air Mouse,

push down then pull to release

the compartment door. (Use the tip

of your finger to open the door.)

Insert the included AAA battery.

Close the battery compartment.

Connect the RF Receiver/Flash Drive

into an available USB port on your

computer. Your operating system

should detect and install the RF

Receiver/Flash Drive. (Check system

requirements for more information on

supported operating systems.)

Turn the GYROTRANSPORT Air Mouse

to profile 1 or 2 to turn on.

1) Press and release the Connect button

on the RF Receiver/Flash Drive. The Status

Light on the Receiver will begin to flash

rapidly, indicating the receiver is in

“Connect Mode.”

2) Press the Connect button located on the

bottom of the GYROTRANSPORT Air Mouse.

The Status Light on the receiver will stop

blinking indicating that a successful

connection has been made. (Connect Mode

will automatically time out after one minute.)

3) Repeat steps 1 and 2 for GO 2.4 GHz

keyboard or any other GO 2.4GHz products.

1) Press and hold the Activation Button with

your thumb and flex your wrist up, down

and sideways (in a manner similar to using

a flashlight). The mouse cursor tracks the

motions of your hand. Remember, it is not

necessary to point the mouse at your

computer, receiver or monitor.

2) Use your thumb to press the left or right

mouse buttons.

3) Double click the Activation Button to keep

the cursor continuously active. To stop the

continuous activation, click the Activation

Button once.

TIP : If your cursor is drifting, simply set

the GYROTRANSPORT down on the desk

for 5 seconds and then proceed.

1) Please visit www.gyration.com

2) Your GYROTRANSPORT Air Mouse includes

a 1 GB

RF Receiver/Flash Drive that is

preloaded with GyroTools™ Media Control

Software PRESENTATION EDITION with the

Help File and Instruction Booklet.

3) Please call 1-888-340-0033

** Actual available storage space varies depending upon system requirements

and other factors.

SETTING UP THE GYROTRANSPORT

PROPER USAGE IN THE AIR

ADDITIONAL GYROTRANSPORT AIR MOUSE INFORMATION

Note: The GYROTRANSPORT and RF Receiver/Flash Drive connect

buttons are countersunk and require use of the tip of a pen or

paperclip (or similar) to press.

www.gyration.com

Status

Light

START

HERE

Connect

Activation Button

Swipes Button

Flip Over

Back of

full-size

keyboard

Front of

compact

keyboard

RF Receiver/Flash Drive

Remove the RF Receiver/Flash Drive from

the bottom of the GYROTRANSPORT Air Mouse.

To open the battery compartment

on the front bottom of the

GYROTRANSPORT Air Mouse,

push down then pull to release

the compartment door. (Use the tip

of your finger to open the door.)

Insert the included AAA battery.

Close the battery compartment.

Connect the RF Receiver/Flash Drive

into an available USB port on your

computer. Your operating system

should detect and install the RF

Receiver/Flash Drive. (Check system

requirements for more information on

supported operating systems.)

Turn the GYROTRANSPORT Air Mouse

to profile 1 or 2 to turn on.

1) Press and release the Connect button

on the RF Receiver/Flash Drive. The Status

Light on the Receiver will begin to flash

rapidly, indicating the receiver is in

“Connect Mode.”

2) Press the Connect button located on the

bottom of the GYROTRANSPORT Air Mouse.

The Status Light on the receiver will stop

blinking indicating that a successful

connection has been made. (Connect Mode

will automatically time out after one minute.)

3) Repeat steps 1 and 2 for GO 2.4 GHz

keyboard or any other GO 2.4GHz products.

1) Press and hold the Activation Button with

your thumb and flex your wrist up, down

and sideways (in a manner similar to using

a flashlight). The mouse cursor tracks the

motions of your hand. Remember, it is not

necessary to point the mouse at your

computer, receiver or monitor.

2) Use your thumb to press the left or right

mouse buttons.

3) Double click the Activation Button to keep

the cursor continuously active. To stop the

continuous activation, click the Activation

Button once.

TIP : If your cursor is drifting, simply set

the GYROTRANSPORT down on the desk

for 5 seconds and then proceed.

1) Please visit www.gyration.com

2) Your GYROTRANSPORT Air Mouse includes

a 1 GB

RF Receiver/Flash Drive that is

preloaded with GyroTools™ Media Control

Software PRESENTATION EDITION with the

Help File and Instruction Booklet.

3) Please call 1-888-340-0033

** Actual available storage space varies depending upon system requirements

and other factors.

SETTING UP THE GYROTRANSPORT

PROPER USAGE IN THE AIR

ADDITIONAL GYROTRANSPORT AIR MOUSE INFORMATION

Note: The GYROTRANSPORT and RF Receiver/Flash Drive connect

buttons are countersunk and require use of the tip of a pen or

paperclip (or similar) to press.

www.gyration.com

Status

Light

Gyration GPT6105 Start Here

Gyration GPT6105 Start Here

Gyration GPT6105 Start Here

Related papers

Other documents