Murata LBEE5PK2BC User manual

Category
Network antennas
Type
User manual

Murata LBEE5PK2BC is a versatile module that seamlessly integrates Bluetooth, 2.4 GHz Wi-Fi, and 5 GHz Wi-Fi capabilities, offering reliable wireless connectivity for various applications. With its compact size and low power consumption, this module is ideal for space-constrained IoT devices requiring wireless data transmission.

Murata LBEE5PK2BC is a versatile module that seamlessly integrates Bluetooth, 2.4 GHz Wi-Fi, and 5 GHz Wi-Fi capabilities, offering reliable wireless connectivity for various applications. With its compact size and low power consumption, this module is ideal for space-constrained IoT devices requiring wireless data transmission.

WLAN+Bluetooth Module User Manual
Part Number: LBEE5PK2BC
LBEE5PK2AE has been FCC/ISED certified as Single Modular Approval with the following IDs.
The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring
that the end-user has no manual instruction to remove or install module.
Therefore, the final host product must be submitted to Murata for confirmation that the
installation for the module into the host is in compliance with regulations of FCC and IC Canada.
Specially, if an antenna other than the model documented in the Filing is used, a Class 2
Permissive Change must be filed with the FCC.
Changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
This module has been approved by FCC to operate with the antenna types with the maximum
permissible gain indicated. Antenna types not included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly prohibited for use with this device. The
following antennas have been certified in combination with the module. Refer to next pages for
the antenna application guidance.
(a) Monopole PCB antenna with peak gains of 3.0dBi (2.4GHz) and 3.3dBi (5GHz);
(b) External dipole antenna with peak gains of 3.4dBi (2.4GHz) and 4.75dBi (5GHz);
The operational temperature is -20°C~70°C.
Antenna Application Guidance Monopole PCB antenna
FCC ID: VPYLB2BC
IC ID: 772C-LB2BC
Antenna Application Guidance External dipole antenna
FCC Statements
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator & your body.
Please notice that if the FCC identification number is not visible when the module is installed
inside another device, then the outside of the device into which the module is installed must also
display a label referring to the enclosed module. This exterior label can use wording such as the
following: “Contains FCC ID: VPYLB2BC” any similar wording that expresses the same meaning
may be used.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of
20cm between the radiator & your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
FCC Statements (cont.)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help
The device must be professionally installed The intended use is generally not for the general
public. It is generally for industry/commercial use.The connector is within the transmitter
enclosure and can only be accessed by disassembly of the transmitter that is not normally
required. the user has no access to the connector. Installation must be controlled. Installation
requires special training This module has been assessed against the following FCC rule parts:
CFR 47 FCC Part 15 C (15.247, DTS and DSS) and CFR 47 FCC Part 15 E (15.407,NII). It is
applicable to the modular transmitter
This radio transmitter FCC ID: VPYLB2BC has been approved by Federal Communications
Commission to operate with the antenna types listed below, with the maximum permissible gain
indicated. Antenna types not included in this list that have a gain greater than the maximum gain
indicated for any type listed are strictly prohibited for use with this device.
The concrete contents to check are the following three points.
) Must use antenna such as dipole antenna (with gain not exceeding 3.4dBi at 2.4GHz &
4.75dBi at 5GHz);
) Should be installed so that the end user cannot modify the antenna;
) Feed line should be designed in 50ohm
Fine tuning of return loss etc. can be performed using a matching network.
L'émetteur radio FCC id: VPYLB2AE a été approuvé par la FCC
Utilisez les types d'antennes énumérés ci - dessous et indiquez le gain maximal admissible. Le
gain du type d'antenne non inclus dans cette liste est supérieur au gain maximal de l'un des
types énumérés et ne doit pas être utilisé avec cet équipement.
Le contenu spécifique de l'inspection comprend les trois points suivants.
1) doit utiliser une antenne comme dipole antenne avec pifa gain n'excédant pas
3.4dBi(2.4GHz) & 4.75dBi(5GHz)
2) Doit être installé là où l'utilisateur final ne peut pas modifier l'antenne;
3) La ligne d'alimentation doit être conçue pour 50 ohms
Le réseau correspondant peut être utilisé pour affiner la perte de retour, etc.
BT/BLE/2.4G WIFI:
Ant.
Frequency (MHz)
Antenna Type
Antenna Gain (dBi)
1
2402-2480
PCB Antenna
3.0
External Dipole Antenna
3.4
5G WIFI:
Antenna
Frequency Band
Maximum Antenna Gain
(dBi)
1
UNII-1
3.3
4.75
1
UNII-2A
3.3
4.75
1
UNII-2C
3.3
4.75
1
UNII-3
3.3
4.75
There is only one antenna port, which is shared by all the radios by time divided.
The module doesn’t have a permanent antenna. The following antennas are certified to be
FCC/ISED regulatory conformity.
(a) Monopole PCB antenna with peak gains of 3.0dBi (2.4GHz) and 3.3dBi (5GHz);
(b) External dipole antenna with peak gains of 3.4dBi (2.4GHz) and 4.75dBi (5GHz);
IC Statements
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of
a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To
reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary
for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour
l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique
à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à
l'établissement d'une communication satisfaisante.
IC Statements (cont.)
This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator & your body.
ce matériel est conforme aux limites de dose d'exposition aux rayonnements, FCC / CNR-102
énoncée dans un autre environnement.cette eqipment devrait être installé et exploité avec
distance minimale de 20 entre le radiateur et votre corps.
Please notice that if the IC identification number is not visible when the module is installed
inside another device, then the outside of the device into which the module is installed must also
display a label referring to the enclosed module. This exterior label can use wording such as the
following: “Contains IC: 772C-LB2BC” any similar wording that expresses the same meaning
may be used.
Notez que si le numéro d'identification IC n'est pas visible lorsque le module est installé dans un
autre appareil, une étiquette indiquant le module attaché doit également être affichée à
l'extérieur de l'appareil où le module est installé. L'étiquette extérieure peut être libellée comme
suit: « contient IC: 772C-LB2BC » toute expression similaire qui exprime le même sens.
The device for operation in the band 51505250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems;
For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the
bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with
the e.i.r.p. limit;
For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the
band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as
appropriate;
Les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour
uneutilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de
satellites mobiles utilisant les mêmes canaux;
Le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et5
470-5 725 MHz doit se conformer à la limite de p.i.r.e.;
Le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz)doit
se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point,
selon le cas.
This radio transmitter 772C-LB2BC has been approved by Innovation, Science and Economic
Development Canada to operate with the antenna types listed below, with the maximum
permissible gain indicated. Antenna types not included in this list that have a gain greater than
the maximum gain indicated for any type listed are strictly prohibited for use with this device.
The concrete contents to check are the following three points.
) Must use antenna such as dipole antenna (with gain not exceeding 3.4dBi at 2.4GHz &
4.75dBi at 5GHz) or PCB antenna (with gain not exceeding 3.0dBi at 2.4GHz & 3.3dBi at
5GHz) ;
) Should be installed so that the end user cannot modify the antenna;
) Feed line should be designed in 50ohm
Fine tuning of return loss etc. can be performed using a matching network.
Le présent émetteur radio 772C-LB2BC a été approuvé par Innovation, Sciences et
Développement économique Canada pour fonctionner avec les types d'antenne énumérés ci-
dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste,
et dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont
strictement interdits pour l'exploitation de l'émetteur.
Le contenu concret à vérifier sont les trois points suivants.
) doit utiliser une antenne comme dipole antenne avec pifa gain n'excédant pas
3.4dBi(2.4GHz) & 4.75dBi(5GHz)
) doivent être installés de façon que l'utilisateur final ne peut pas modifier l'antenne
) La ligne d’alimentation doit être conçue en 50ohm
Le réglage précis de la perte de rendement, etc. peut être effectué en utilisant un réseau
correspondant.
BT/BLE/2.4G WIFI:
Ant.
Frequency (MHz)
Antenna Type
Antenna Gain (dBi)
1
2402-2480
PCB Antenna
3.0
External Dipole Antenna
3.4
5G WIFI:
Antenna
Frequency Band
Maximum Antenna Gain
(dBi)
1
UNII-1
3.3
4.75
1
UNII-2A
3.3
4.75
1
UNII-2C
3.3
4.75
1
UNII-3
3.3
4.75
There is only one antenna port, which is shared by all the radios by time divided.
The module doesn’t have a permanent antenna. The following antennas are certified to be
FCC/ISED regulatory conformity.
(a) Monopole PCB antenna with peak gains of 3.0dBi (2.4GHz) and 3.3dBi (5GHz);
(b) External dipole antenna with peak gains of 3.4dBi (2.4GHz) and 4.75dBi (5GHz);
Notice to OEM integrator
Must use the device only in host devices that meet the FCC/ISED RF exposure category of
mobile, which means the device is installed and used at distances of at least 20cm from
persons. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements
related to the transmitter as show in this manual(FCC/ICanada statement). Host manufacturer is
responsible for compliance of the host system with module installed with all other applicable
requirements for the system such as Part 15 B, ICES 003. Host manufacturer is strongly
recommended to confirm compliance with FCC/ISED requirements for the transmitter when the
module is installed in the host.
Must have on the host device a label showing Contains FCC ID: VPYLB2AEIC: 772C-LB2AE
The use condition limitations extend to professional users, then instructions must state that this
information also extends to the host manufacturer’s instruction manual.
This module is stand-alone modular. If the end product will involve the Multiple simultaneously
transmitting condition or different operational conditions for a stand-alone modular transmitter in
a host, host manufacturer have to consult with module manufacturer for the installation method
in end system. Any company of the host device which install this modular should perform the
test of radiated & conducted emission and spurious emission etc. according to FCC Part 15C:
15.247 and 15.209 &
15.207, 15B class B requirement, only if the test result comply with FCC part 15C: 15.247 and
15.209 & 15.207, 15B class B requirement. Then the host can be sold legally.
This modular transmitter is only FCC authorized for the specific rule parts ( 47CFR Part 15.247
and 15.407) listed on the grant, and that the host product manufacturer is responsible for
compliance to any other FCC rules that apply to the host not covered by the modular transmitter
grant of certification. Host manufacturer is strongly recommended to confirm compliance with
FCC/ISED
requirements for the transmitter when the module is installed in the host. Must have on the host
device a label showing Contains FCC ID: VPYLB2BC and Contains IC: 772C-LB2BC
l'hôte doit utiliser l'instrument uniquement dans des dispositifs qui répondent à la fcc / (catégorie
d'exposition rf mobile, ce qui signifie le dispositif est installé et utilisé à une distance d'au moins
20 cm de personnes. le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen dé
clarations de conformité relatives à l'émetteur que de montrer dans ce manuel. le fabricant est
responsable de la conformité de l'hôte, le système d'accueil avec le module installé avec toutes
les autres exigences applicables du système comme la partie 15 b, ices - 003. accueillir le
fabricant est fortement recommandé de confirmer la conformité avec les exigences de la fcc / (é
metteur lorsque le module est installé dans l'hôte. le dispositif d'accueil doivent avoir une é
tiquette indiquant contient FCC ID: VPYLB2BCIC: 772C-LB2BC
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Murata LBEE5PK2BC User manual

Category
Network antennas
Type
User manual

Murata LBEE5PK2BC is a versatile module that seamlessly integrates Bluetooth, 2.4 GHz Wi-Fi, and 5 GHz Wi-Fi capabilities, offering reliable wireless connectivity for various applications. With its compact size and low power consumption, this module is ideal for space-constrained IoT devices requiring wireless data transmission.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages