2. Home
  3. Domestic appliances
  4. Sanitary ware
  5. YITAHOME
  6. BFBPBA-1001
BFBPBA-1001

YITAHOME BFBPBA-1001 User manual

  • Hello! I am an AI chatbot trained to assist you with the YITAHOME BFBPBA-1001 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
ASSEMBLY INSTRUCTIONS
BIDET ATTACHMENT
Pure & Easy
CONTACT US:
If you have any questions about the installation of YITAHOME® products，just contact us
at +1(888)-717-8084 from Mon-Fri 8:00 AM-16:30 PM PST / Saturday 8:00 AM-12:00 PM PST
(except holidays) or E-mail us at: after-sale.cs@hotmail.com
Alternative method to contact us(amazon.com orders only)
1.Log into your amazon account
2.Go to "Your Orders" and find the purchase
3.Click on "Contact Seller"
BFBPBA-1001
ASSEMBLY INSTRUCTIONS
1 2
ASSEMBLY INSTRUCTIONS
Note ：
1. Follow the instructions during installation.
2. Check that you have access to the fill valve under the toilet tank, if not, contact Our Customer
Support ASAP.
3. Check that your toilet tank water supply line is flexible, if not, you will need to replace this pipe
with a flexible water supply hose.
Function Parts:
*Please Note : lllustration will vary depending on the product model.
Water Flow & Water Temperature Control Handle
Function Selection Knob
The extra installation tools you may needed:
Flat screwdriver Wrench
Reference Image
Braided Cold Water Hose
Wrench Hot/Cold Water Inlet Plug
PU Hot Water Hose
Cold Water T-adapter
Hot Water T-adapter
Qty.
X1
X1
X1
Reference Image Qty.
X1
X1
X1
ASSEMBLY INSTRUCTIONSASSEMBLY INSTRUCTIONS
3 4
1. Turn off the toilet water supply
valve. Flush to empty the toilet 2. Unscrew the toilet seat to make
2cm gap between the toilet seat and
the toilet. Be sure not to completely
unscrew the toilet seat.
4. Adjust the bidet nozzle so that it’s placed in the center of the toilet.
5. Screw the toilet again
3. Aim the U-type groove located on the two rotatable mounting discs
at two bolts, then push the bidet toward the 2 cm gap.
ASSEMBLY INSTRUCTIONSASSEMBLY INSTRUCTIONS
5 6
6. There should be a black rubber washer inserted inside the top of Metal
T-adapter. If not, please insert a rubber washer as shown in fig.6.2
Metal
9. Connect the braided stainless steel hose to the bidet’s cold water inlet.
10.There should be a black rubber washer inserted inside the top of plastic
T-adapter. If not, please insert a rubber washer as shown in fig.10.2
8. Connect the braided stainless steel hose to the Metal T-adapter
7.1.
Firstly turn off the toilet water
supply valve
Secondly flush the toilet and
make sure there is no water
in the toilet cistern.
7.2.Connect the metal
T-adapter to the toilet water
supply as shown in the fig.7.2
Notes
don’t use excessive force when
tightening the connector.
Tighten for a quarter or half a turn
by using a wrench.
11.
Metal
7 8
ASSEMBLY INSTRUCTIONSASSEMBLY INSTRUCTIONS
Using Instruction
12.11.3: Unscrew the thumb nut from the hot water adapter
11.4: Place the thumb nut on the end of hot water tube
11.5: Screw in the thumb nut so that the hot water adapter protects
the connecting part.
11.6: Connect the metal end of hot water tube to the hot water inlet
COLD HOT
Women Nozzle
Wash
COLD HOT
Women Nozzle
Wash
COLD HOT
Women Nozzle
Wash
COLD HOT
Women Nozzle
Wash
COLD HOT
Women Nozzle
Wash
1. Switch the knob to "Wonmen" for feminine washing
2. Switch the knob to "Wash" for rear washing
3. Switch the knob to "Nozzle Cleaning" for cleaning the 2 nozzles
1. Knob switch to adjust washing mode
1. Lift up or turn down the lever to get gentle pressure or strong pressure
2. Turn the lever to "COLD" for low temperature, "HOT" for higher temperature
2. Chrome-plated lever to adjust water pressure and temperature
Do not use hot water at the when you start to use.
Do not flush the toilet when you using the bidet.
Troubleshooting Tips
Question: There are leaks in the bidet body and hose connections.
Answer:
1. Make sure that all threads are properly installed and tightened;
2. Contact us via [email protected] if the problem persists.
Question: The nozzle sprays too far forward.
Answer: Adjust the bidet by pushing it back towards the toilet tank.
Question: After installing the bidet, the toilet seat isn’t flat on the toilet bowl.
Answer:
1. If the extra gap is 1/2” or less, please install toilet seat bumpers
2. Find a toilet seat that is flat at the bottom without any outer hinge tabs.
Question: The toilet seat bolts do not properly affix to the toilet after bidet installation.
Answer: Install longer toilet seat bolts that accommodate the extra space of the bidet.
Question: How to maintain the nozzle?
Answer: You can clean it once a week with paper towels soaked in vinegar to safely dissolve any hard water.
For additional troubleshooting tips, please contact our customer service or email
our [email protected]
Pay Attention
1 2
/