27910.98in
2168.5in
Part Description Quantity
ABidet attachment 1
C1
B3 1
B2 1
BNozzle 1
Clamping ring (preassembled in the nozzle)
O-ring (preassembled in the nozzle)
Hose
E1
D1
Washer
T-Valve
PACKAGE CONTENTS
□ Use this product only for its intended use as directed in this manual.
□ Do not disassemble, repair, or remodel the unit, as this will void the warranty.
□ Do not stand or drop heavy objects on this product and do not insert any object into
openings or hose.
□ Tighten the connections.
□ Please use the supplied T-valve, hose and bidet attachment as a set.
□ When you use the bidet, do not flush the toilet at the same time.
Pre-Installation
□ Turn off the water supply before installing this bidet attachment.
□ Before begining the installation of this product, ensure all parts are present.
□ Compare all the parts with the Package Contents section of this manual. If any part is
missing or damaged, do not attempt to assemble, install, or operate the product.
□ Contact customer service for replacement parts at 1-855-HD-GLACIER
or visit www.HomeDepot.ca.
□ Estimated Installation Time: 8 minutes.
TOOLS REQUIRED
Phillips Screwdriver Wrench
Safety Information
C
D
E
B
B2
B3
A
Installation (continued)
□ Slowly turn the water supply valve back
on, check for leaks, and test the unit for
functionality.
□ After installing your bidet attachment (A),
check to see if there is a gap between the
toilet base and toilet seat.
Horizontal 105 – 205 mm
Vertical 38 – 89mm
3°C – 35°C
3°C – 40°C
0.05 MPa – 0.6 MPa
Water Temperature
Room Temperature
Water Pressure
Distance between Holes Axis
SPECIFICATIONS
Installation
□ Place the bidet (A) on the toilet with
the mounting brackets over the bolt
holes and make any needed adjustments
to make sure the bidet (A) is centered on
the toilet.
□ Verify that the nozzle (B), O-ring (B2
)
,
and clamping ring (B3) are
assembled correctly.
□ Insert the nozzle (B) with its “unlock”
symbol aligned with the triangle on the
water distribution head.
□ Turn the nozzle (B) clockwise to the
“locked” position.
□ Remove the existing toilet seat by
locating the bolts and nuts, typically under
a plastic cover, and removing them first.
1 2
43
9
C
A
E
A
C
E
B
B2
B3
AB
Triangle
5
7
□ Connect the hose (C
)
to the open side of
the T-valve (E
)
.
□ Connect the other end of the hose (C
)
to
the bidet water connection underneath the
handle of the bidet (A
)
.
□ Turn water supply valve off and flush the
toilet completely so that there is little to no
water left in the toilet tank.
□ Disconnect the water hose from
underneath the toilet tank.
□ Connect the T-valve (E) to the toilet fill valve
where you just removed the water hose from.
□ Attach the water supply hose to the bottom
of the T-valve (E).
□ Place the toilet seat back on the toilet
over the bidet (A) and secure the bolts so
that the seat and bidet attachment (A) are
stable.
Installation (continued)
6
8
Angle valve
A
A
E
D
The wall or
barrier on the
left side of the
toilet
Adjustable scope
a
b
c
d
A
Verifying the nozzle assembly Installing the nozzle
Removing the existing
toilet seat
Finishing installation
Adjusting the installation
scope
Connecting to the water
supply
Connecting the hose to bidet
Reinstalling the toilet seat Turning off the water supply
Adjusting The Nozzle Angle to Chose Wash Mode
Posterior Mode Feminine Mode
SwitchSwitch
□ Push the switch backward to put the nozzle angle in posterior mode.
□ Push the switch forward to put the nozzle angle in feminine mode.
OFF
72°
Self-cleaning
Wash
Knob Operation
144°
□ Turn the knob counterclockwise towards the “Self-cleaning” position. The further the knob
is turned, the higher the water pressure will be.
□ Turn the knob counterclockwise towards the “Wash” position. The further the knob is
turned, the higher the water pressure will be.
The spray nozzle
has no water
Low water pressure
Problem Solution
□ The water supply is cut off.
□ The angle valve is closed.
□ The spray nozzle is clogged.
□ Low water pressure.
□ Water supply pipe is bended.
□ The water flow control knob is adjusted to be low position.
□ Water supply pipe is bended.
Self-cleaning is
not clean
□ Pls check if the water pressure is too low, the water
pressure needs to be 0.2MPA, which can realize
self-cleaning without dead ends.
□ Cleaning time should be more than 8 seconds to ensure
fully cleaning.
Troubleshooting
USE AND CARE GUIDE
PLASTIC COLD WATER BIDET ATTACHMENT
THANK YOU
We appreciate the trust and confidence you have placed in Glacier Bay through the
purchase of this single nozzle bidet attachment. We strive to continually create quality
products designed to enhance your home. Visit us online to see our full line of products
available for your home improvement needs. Thank you for choosing Glacier Bay!
GLACIER
Item # 1008162502
Model # T3204-30
F0078客户说明书
52211929-01
279X216 mm
铜版纸105g
QI-02-F00784-01
2022-07-17
1-0
1
American Standard 8013A80GPCH-020 Installation guide
Luxe BidetNeo185sww User manual
LUXE Bidet BidetNeo120s User manual
bioBidet BB-600R79061 Installation guide
bioBidet BB-1000R User guide
Bio Bidet M35779 Operating instructions
bioBidet BB600 Owner's manual
bioBidet BB-600 Installation guide
Uspa UB-6335 Operating Instructions Manual
