2. Computers & electronics
  3. Telecom & navigation
  4. Mobile phones
  5. Car kits
  6. Toro
  7. Dirt Stakes, 2024 Directional Drill
Dirt Stakes, 2024 Directional Drill

Toro Dirt Stakes, 2024 Directional Drill, Dirt Stakes, 4045 Directional Drill, Rock Stakes, 2024 Directional Drill, Rock Stakes, 4045 Directional Drill Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Toro Dirt Stakes, 2024 Directional Drill Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the purpose of the stake guide and guide ring?
    How many bolts are needed to secure the coupler to the machine?
    What is the torque specification for the bolts securing the coupler to the machine?
    How many grease fittings are needed for the coupler?
    How much grease should be pumped into the fittings?
    How many bolts are needed to secure the stake guide to the guide ring base?
    What is the torque specification for the bolts securing the stake guide to the guide ring base?
FormNo.3398-624RevA
DirtandRockStakes
2024and4045DirectionalDrill
ModelNo.23812
ModelNo.23812E
ModelNo.23813
ModelNo.23813E
ModelNo.23814
ModelNo.23814E
ModelNo.23815
ModelNo.23815E
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato
causecancer,birthdefects,orreproductiveharm.
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
Description
Qty.
Use
2024Dirtstakes2
2024Rockstakes2
Coupler
2
Stakepin
2
O-ring
2
Locknut(M12)
8
Bolt(M12-13/4x80mm)
8
Greasetting
2
Stakeguide
2
Guidering
2
Bolt(M8-11/4x20mm)
8
Installthestakesonthe2024directionaldrill.
RockorDirtstake2
Guidering
2
Stakeguide
2
Bolts(M10-11/2x25mm)
6
Installthestakesforthe4045directionaldrill.
©2015—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.
OriginalInstructions(EN)
PrintedintheUSA.
AllRightsReserved
*3398-624*A
InstallingtheStakesonthe
2024DirectionalDrill
PreparingtheMachineandInstalling
theCoupler
Note:Having2peopleoraliftingmechanismmakesiteasier
toinstallthestakes.
1.Positionthethrustframe25.4cm(12inches)offthe
ground,withthestakesintheupposition.
2.Turnofftheengineandthebatterydisconnectswitch.
3.Ifyourmachinehasacage,removethestake-down
cageassembly.
4.Whileholdingthestakes,removetheO-ringsandpins
securingthestakestothemotors(Figure1).
Figure1
1.Motor
3.PinandO-ring(pinand
e-clipon4045)
2.Coupler4.Stake
5.Removetheexistingstakes.
6.Removetheexistingcouplersandinstallthenew
couplersusing8bolts(M12-13/4x80mm),8locknuts
(M12),and2greasettings(Figure2).
Figure2
1.Greasetting3.Locknut(M12)
2.Bolt(M12)4.Coupler
7.Torquetheboltsto127to155N-m(94to114ft-lb).
8.Pumpgreaseintothettingsuntilgreasebeginsto
oozeoutofthebearings(approximately3pumps)and
wipeupanyexcessgrease.
InstallingtheDirtStakesonthe2024
DirectionalDrill
Installthenewstakesbyaligningtheholeinthestakewith
theholeinthemotorcouplerandsecureitwiththeO-rings
andpinsincludedinthiskit(Figure3).
Figure3
1.Coupler3.O-ring
2.Pin
4.Stake
Ifyourmachinehasacage,installthecageassemblyandlatch
thecagedoor.
2
InstallingtheRockStakesonthe2024
DirectionalDrill
1.Securethestakeguideontotheguideringusingthe8
bolts(M8)(BoxAofFigure4).
Figure4
1.Bolts(M8)3.Guidering
2.Stakeguide
2.Placetheassemblyintotheholeofthethrustframe
foot.
3.Aligntheboltheadssothattheyaresquarewiththe
foot.
4.Weldtheguideringontothemachineusing7equally
spaced5cmby0.64cm(2inchby0.25inch)weldsas
showninBoxBofFigure4.
5.Removetheboltsandstakeguide(BoxCofFigure4).
6.Painttheweldedareawithblackpaint.
7.Placethestakeguideonthestakeandguidethestake
intotheguideringonthemachine(BoxDofFigure4).
8.Installthenewstakesbyaligningtheholeinthestake
withtheholeinthemotorcouplerandsecureitwith
theO-ringsandpinsincludedinthiskit(Figure3).
9.Securethestake-guideringontheweldedguidering
usingthe8bolts(M8-11/4x20mm)(Figure4).
10.Torquetheboltsto23to29N-m(17to21ft-lb).
InstallingtheStakesonthe
4045DirectionalDrill
PreparingtheMachineandRemoving
theCurrentStakes
Note:Having2peopleoraliftingmechanismmakesiteasier
toinstallthestakes.
1.Positionthethrustframe25.4cm(12inches)offthe
ground,withthestakesintheupposition.
2.Turnofftheengineandthebatterydisconnectswitch.
3.Supportthefootwithajackstandorequivalent.
4.Ifyourmachinehasacage,unlatchandopenthe
stake-downcagedoor.
5.Whileholdingthestakes,removethepinsande-clips
securingthestakestothemotors(Figure1).
6.Removetheexistingstakes.
InstallingtheDirtStakesonthe4045
DirectionalDrill
Installthenewstakesbyaligningtheholeinthestakewith
theholeinthemotorandsecureitwiththepinsande-clips
previouslyremoved(Figure5).
Figure5
Rockstakesshownforillustrativepurposesonly
1.Coupler3.Stake
2.Pin
3
InstallingtheRockStakesonthe4045
DirectionalDrill
Have2peopleperformthisprocedure.
1.Slidethestakeguideoverthetopoftherockstakeand
placethestakeonthemachineasshowninFigure6.
Note:Have1personholdthestakeinplacewhilethe
otherpersoncontinuesthisprocedure.
Figure6
2.Looselysecurethestakeguidetotheguideringbase
usingthe6Bolts(M10-11/2x25mm)asshownin
Figure7.
Figure7
1.Bolts(M10)
3.Insertthestakeguidefromundertheplatform(Figure
8)andtightenthebolts.
Figure8
1.Stakeguide
4.TorquetheM10boltsto73to89N-m(54to66ft-lb).
5.SecurethestaketothemotorasshowninFigure5.
6.Ifyourmachinehasacage,closeandlatchthecage
door.
Important:Removetheguideringfromthefootwhen
switchingfromtherockstakestothedirtstakes.
4
/