NICOR CLR6-10-UNV-30K-WH Installation guide

Brand: NICOR

Model: CLR6-10-UNV-30K-WH

Type: Installation guide

What’s In The Box

One (1) CLR Five (5) Wire NutsOne (1) MC Connector

ATTENTION:

• Turn power o before inspection, installation, or removal.

• Suitable for use in dry, damp and wet indoor and outdoor locations. Use only on 120-277 VAC, 60Hz circuits.

NOTE:

• Not all existing mounting frames will be compatible with the CLR. To ensure compatibility, a test installation should be conducted.

• The CLR LED Retrot Kit is designed to be installed in a standard 6” or 8” CFL mounting frame.

CLR Commercial Recessed LED Downlight

INSTALLATION INSTRUCTIONS

Model(s):

CLR6-10-UNV-#K-WH

CLR8-10-UNV-#K-WH

Tools Needed Frame Compatibility

This LED Recessed Kit requires very few tools for

installation. A screwdriver and a pair of wirecutters will

help to install the downlight to a JBox or housing.

CLR6: 5½” min - 7” max

CLR8: 7¼” min - 9” max

Remove existing

lamp, trim and

socket cap.

Remove J-Box cover plate from existing lamp ballast. Do

not dispose. Disconnect all wires from ballast. Remove

the socket cap metal conduit (MC) cable from the J-Box.

CLR Kit Installation With Existing Frame

Make sure all power is turned o before beginning installation

WARNING:

• Risk of electric shock. Disconnect power at fuse or circuit breaker before installing or servicing.

• To prevent early lamp failure, lamp should only be installed in operating environments between -20°C and + 40°C (104°F and -4°F)

• No user serviceable parts inside. To avoid electric shock do not disassemble product.

• This product is not intended for use in emergency light xtures or exit signs.

• This product is contains a chemical know to the state of California to cause cancer, birth defects and other reproductive harm.

• Risk of re or electrical shock. Install this kit only in luminaires that have the construction features and dimensions shown in

the photographs and/or drawings.

• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

CLR Kit Installation With Existing Frame

Make sure all power is turned o before beginning installation

Turn on power and verify proper operation.

Fasten the LED retrot kit MC cable to the J-Box using the included MC connector.

Make wiring connection to junction box.

a. Connect Black wire to line wire.

b. Connect White wire to neutral wire

c. Connect Green wire to ground wire

d. Route and connect Purple and Grey 0-10V dimming

control wires in accordance with dimmer instructions

and electrical code.

Put back J-Box cover plate

(with lamp ballast still

attached to it).

Lift upward on retention tabs while pushing the retrot

kit through the rough-in, release the retention tabs and

push trim ush to the ceiling, ensuring a secure t.

EXISTING BALLAST BOX

LINE

Black (line)

Ground

White (neutral)

Purple (dim +)

Grey (dim -)

Black (line)

Green (ground)

White (neutral)

Purple (dim +)

Grey (dim -)

CLR

NOTE: If 0-10V dimming is NOT to be connected, it is recommended to cut o the exposed, tinned leads on the purple and

grey wires, and cover the ends with a small piece of electrical tape or wire nut. If bare 0-10V control wires should

accidentally touch a grounded surface, it could cause unintended ickering or dimming of the light xture.

CLR Kit Installation Without Existing Frame

Make sure all power is turned o before beginning installation

Make wiring connection to junction box.

a. Connect Black wire to line wire.

b. Connect White wire to neutral wire

c. Connect Green wire to ground wire

d. Route and connect Purple and Grey 0-10V dimming control wires in accordance with dimmer instructions

and electrical code.

Identity xture location and cut rough-in hole. Cut a 5½” to

7” diameter hole for CLR6 and a 7½” to 9¼” diameter hole

for CLR8.

Fasten the LED

retrot kit MC

cable to a eld

installed j-box

(not supplied)

per local

electrical code

using a standard

MC connector

(not supplied).

1 2

Install J-Box

cover plate.

Lift upward on retention tabs while pushing the retrot kit

through the rough-in, release the retention tabs and push

trim ush to the ceiling, ensuring a secure t.

4 5

J-Box

LINE

Black (line)

Ground

White (neutral)

Purple (dim +)

Grey (dim -)

Black (line)

Green (ground)

White (neutral)

Purple (dim +)

Grey (dim -)

CLR

Turn on power and verify proper operation.

NOTE: If 0-10V dimming is NOT to be connected, it is recommended to cut o the exposed, tinned leads on the purple and

grey wires, and cover the ends with a small piece of electrical tape or wire nut. If bare 0-10V control wires should

accidentally touch a grounded surface, it could cause unintended ickering or dimming of the light xture.

CLR6 CLR8

5½” to 7” diameter

7½” to 9¼” diameter

Turn over for warranty information.

EXPRESS LIMITED WARRANTY

Subject to the exclusions contained below, NICOR Inc. (NICOR) warrants that all NICOR LED branded Solid State Lighting products made by NICOR to be free from defects in materials and workmanship, under normal consumer usage

for a period of 5 years from date of purchase. This limited warranty is a consumer’s exclusive remedy, and applies only to new products purchased and used by consumers in the United States or Canada, which are accompanied by

this written warranty.

This limited warranty extends only to the rst consumer purchaser, and is not transferable. A consumer wishing to invoke the terms of this warranty must rst obtain a RGA number within 30 days of discovery of the defect, and

return the product to NICOR for inspection. Once veried to be covered by this limited warranty, NICOR will, at its discretion, repair, replace or refund the purchase price of any product that does not conform to this limited warranty.

This limited warranty covers only defects in material and workmanship associated with normal installation and intended use of the product.

THIS LIMITED WARRANTY DOES NOT COVER THE FOLLOWING:

• Defects or damages resulting from improper operation, storage, misuse or abuse, accident or neglect;

• Defects or damages resulting from improper service, testing, adjustment, installation, maintenance, alteration, connection to out-of-specication electrical service, corrosive or damp environments, or connection to incompatible

equipment or devices (e.g., connecting non-dimmable lighting products to dimmers);

• Damage which occurs in transit; and

• Labor or other charges or expenses associated with the removal, repair, or re-installation of defective or replacement products.

ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY,

OTHERWISE THE REPAIR, REPLACEMENT OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED. IN NO EVENT SHALL NICOR BE LIABLE, WHETHER IN CONTRACT OR IN TORT (INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL

OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE ABILITY OR INABLILITY TO USE THE PRODUCT TO THE

FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.

Revised November, 2016

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including inter-

ference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

NICOR CLR6-10-UNV-30K-WH Installation guide

NICOR CLR6-10-UNV-30K-WH Installation guide

NICOR CLR6-10-UNV-30K-WH Installation guide

Related papers

Other documents