Acrosser Technology AR-R5800 User manual

Brand: Acrosser Technology

Model: AR-R5800

Category: Motherboards

Type: User manual

This manual is also suitable for

AR-B5800A

AR-B5800 User Manual

AR-B5800 Board

Intel® Core™2 LGA775 PROCESSOR

Networking Board

User Manual

Manual Rev.: 1.3

AR-B5800 User Manual

Manual’s first edition:

For the purpose of improving reliability, design and function, the information in this document is

subject to change without prior notice and does not represent a commitment on the part of the

manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential

damages arising out of the use or inability to use the product or documentation, even if advised of

the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are reserved. No

part of this Manual may be reproduced by any mechanical, electronic, or other means in any form

without prior written permission of the manufacturer.

Trademarks

AR-B5800 is a registered trademarks of Acrosser; IBM PC is a registered trademark of the

International Business Machines Corporation; Pentium is a registered trademark of Intel

Technologies Inc; Award is a registered trademark of Award Software International Inc; other

product names mentioned herein are used for identification purposes only and may be trademarks

and/or registered trademarks of their respective companies.

AR-B5800 User Manual

Table of Contents

1 Introduction........................................................5

1.1 ........................................................................6 Specifications

1.2

.................................................................7 Package Contents

1.3

.......................................................................8 Block Diagram

2 H/W Information .................................................9

2.1 Locations (Top side) ..............................................................9

2.2 Connectors and Jumper Setting...........................................11

2.3 Connector and Jumper Setting ............................................13

3 BIos setting.......................................................17

3.1 Main Setup...........................................................................18

3.2 Advanced Chipset Setup .......................................................... 19

3.3 PnP/PCI Setup ...........................................................................

20

3.4 Peripherals Setup.......................................................................

21

3.5 PC Health Setup.........................................................................

23

3.6 Boot Setup ..................................................................................

23

3.7 Exit Setup ....................................................................................

24

3.8 BIOS Update...............................................................................

26

4 Software Installation and Programming Guide31

4.1 ..........................................................................31 Introduction

4.2

..................................................................33 File Descriptions

4.3

....................................................36 API List and Descriptions

AR-B5800 User Manual

1 Introduction

AR-B5800 is designed for rack-mounted platform for networking appliance, e.g. VPN, SSL, UTM or

firewall. With Intel advanced Core 2 Quad / Duo / Pentium / Celeron CPU, AR-B5800 is a powerful

platform to satisfy different applications. By eight 10/100/1000Mbps LANs, the AR-B5800 is

sufficient for the small to middle size business security solution.

AR-B5800 can install 2 x HDD for RAID 0/1 redundancy. Customers don’t need to worry about

data lost due to HDD defected problem. BIOS, GPIO and Jumper can control LAN bypass feature.

It provides flexibility to access Internet by user setting. It also has standard PCIe x 8 slot.

Customers can purchase suitable add-on card to meet their appliance.

Key features:

1. Support Intel Core 2 Quad or Core 2 Duo or Pentium or Celeron CPU

2. Intel G41 + ICH7R Chipset to support RAID 0/1 redundancy

3. DDRIII DIMM x 2, up to 4GB memory

4. Intel 82574L 10/100/1000Mbps x 6 + 82541PI 10/100/1000Mbps x 2

5. Two pairs LAN ports support bypass feature (LAN 1/2 + LAN 3/4)

6. LAN bypass can be controlled by BIOS, GPIO and Jumper

7. CF socket, 2.5” HDD x 2, SATA II interface x 2

8. Console, VGA (pinhead), USB 2.0 x 4 (2 x connectors, 2 x pin head)

9. Support boot from LAN, console redirection

10. Support standard PCIe x 8 slot for feature expansion

AR-B5800 User Manual

1.1 Specifications

 CPU: a LGA775 socket for Intel Core2 Processors in the 775-Land LGA package.

 DMA channels: 7.

 Interrupt levels: 16 (24 APIC interrupts).

 Chipset: Intel G41 express chipset 82G41 + 82801GR + W83627DHG-P.

 Memory: provides two 240-pin DIMM sockets to support DDRIII 1066 non-ECC DIMM. The

memory capability can up to 2GB.

 VGA Controller: G41 GMCH integrated.

 Analog Display Interface: 10-pin box header, and resolution up to 2048x1536@75Hz.

 Serial ATA Interface: supports Two SATA devices, and data transfer rates up to 300MB/s per

device.

 Compact flash interface: supports TYPE-II compact flash card with UDMA supported.

 USB2.0 interface: one stacked USB connector and two 10-pin pin header to support Six

USB2.0 compatible devices. All resettable fuses protected.

 Ethernet interface: on-board six PCI express gigabit Ethernet controllers and two PCI gigabit Ethernet

controllers to support eight LAN ports. They provide a standard IEEE 802.3 Ethernet interface for

1000BASE-T, 100BASE-TX, and 10BASE-T applications (802.3, 802.3u, and 802.3ab,

respectively).

 BYPASS function: supports by ports LAN1 & LAN2 , LAN3 & LAN4 software programmable.

 PCIE X8 interface: One PCI Express x8 slot.

 Serial ports (RS232): One high-speed 16550 compatible UARTs ports with 16-byte

send/receive FIFOs.

COM1: RJ45 connector.

 LCM interface: a 7-pin pin header could be used to LCM for chassis’ control panel.

 General Purpose Input/Output: 8-bit, 3.3V TTL level, bidirectional, and software

programmable GPIOs.

 WATCHDOG: software programmable 1~255 second(s) / minute(s).

 Power Consumption: +12V [5.3A], +5V [3.5A], +3.3V [1.8A], -12V [0.9A], +5Vsb [0.8A]

typically.

Test equipments list as below:

Main board: AR-B5800.

Processor: Intel Pentium Processor E6500 2.93GHz / FSB1066 / 2MB

L2 cache / 45nm.

Memory: one Kingston KVR1333D3N9/2G.

One 3.5” HDD

OS: Windows XP SP3.

AR-B5800 User Manual

Processor was running at 100% loading.

Note: A proper power supply unit choice means that we should consider at least about

a.) Protection of overload, short-circuit, and other safeties.

b.) Summation of all devices’ power requirements.

c.) Thermal de-rating.

1.2 Package Contents

Check if the following items are included in the package.

In addition to this User's Manual, the AR-B5800 package includes the following items:

 A quick setup manual.

 One AR-B5800 networking board.

 One Software utility CD.

 One adaptable cable for COM1.

 One D-SUB-15 adaptable cable for VGA.

 One SATA cable.

 One USB adaptable cable. (Optional) (ACROSSER’s P/N.190030779-G)

AR-B5800 User Manual

1.3 Block Diagram

AR-B5800 User Manual

2 H/W Information

This chapter describes the installation of AR-B5800. At first, it shows the Function diagram and the

layout of AR-B5800. It then describes the unpacking information which you should read carefully,

as well as the jumper/switch settings for the AR-B5800 configuration

2.1 Locations (Top side)

AR-B5800 User Manual

RTC1

System RTC battery socket

Intel ICH7R

PCIEXP1

PCI-Express X8 Slot

DIMM1

240-Pin DDR3 Socket

LGA775 CPU Socket

DIMM2

240-Pin DDR3 Socket

Intel GMCH 82G41

AR-B5800 User Manual

2.2 Connectors and Jumper Setting

2.2.1 Locations (Top side)

AR-B5800 User Manual

LAN1

LAN1 RJ45 Connector

FP_USB1

Internal USB2, USB3 connector.

SYSFAN2

System FAN Connector.

LAN2

LAN2 RJ45 Connector

LCM1

Pin Header for LCM

SYSFAN1

System FAN Connector.

LAN3

LAN3 RJ45 Connector

GP1

GPIO Header.

JP1

For LAN1/LAN2 Bypass Function

Select.

LAN4

LAN4 RJ45 Connector.

JP2

GPIO Header Voltage Selection.

RTC1

CR2032 Battery Hold Connector.

LAN5

LAN5 RJ45 Connector

CF1

CF CARD SOCKET.

CCMOS1

CMOS Memory Clearing Header

LAN6

LAN6 RJ45 Connector

CPLD1

For CPLD Firmware Update

JP4

For LAN3/LAN4 Bypass Function

Select.

LAN7

LAN7 RJ45 Connector.

ATXPWR1

ATX Power Supply input connector..

LAN8

LAN8 RJ45 Connector.

SATA2

SATA device connector #2.

USB1

Two USB ports (USB0, USB1)

connector.

SATA1

SATA device connector #1.

COM1

RS232 Serial Port COM1.(RJ45)

VGA1

VGA connecter (2x5 Pin Header)

LED1

4 in 1 LED for LAN Bypass, Power &

HDD LED.

ATX12V1

ATX12V Power Supply input

Connector.

RST2

System Reset Switch.

SYSFAN3

System FAN Connector.

FP_USB2

Internal USB4, USB5 connector.

CPUFAN1

CPU FAN Connector.

AR-B5800 User Manual

2.3 Connector and Jumper Setting

1. LAN1 ~ LAN8 RJ45 Connector 9. USB1 Connector

LAN RJ45 Connector

Connects to Local Area

Network.

External USB Connector

Connects to USB devices such as scanner,

digital speakers, monitor

, mouse, keyboard, hub, digital camera,

joystick etc.

10. COM1 ( RJ45 Connector ) 11. LED1

COM Port RJ45 Connector

Green1: Power ON LED.

Green2: HDD LED

Yellow1: LAN3&LAN4 Bypass LED.

Yellow2: LAN1&LAN2 Bypass LED.

12. RST2 13,14. FP_USB1 & FP_USB2

Push this button to reset

the system.

AR-B5800 User Manual

15. LCM1 ( for LCM use ) 16. GP1 ( GPIO Header )

Pin SIGNAL

1 Pull-High to VCC5

2 VCC5

3 SOUTB

4 SINB

5 RTSB#

6 CTSB#

7 GND

AL PIN SIGNAL PIN SIGN

VCC_GP D

GP30

GP34

GP31

GP35

GP32

GP36

7 GP33

GP3

17. JP2 GPIO Header Voltage Selection 18. CF1 ( CF CARD Socket )

Pins 1 and 2 shorted

(Default): VCC 5

Pins 2 and 3 shorted:

VCC 3

19. CPLD1 ( for CPLD Firmware Update)

20. ATXPWR1 ( ATX Power Supply Input )

Pin SIGNAL

1 3VDUAL

2 G_TDO

3 G_TDI

4 NC

5 NC

6 G_TMS

7 GND

8 G_TCK

AR-B5800 User Manual

21,22. SATA2, SATA1 (SATA device

connector #2 and #1).

23. VGA1 (2x5pin 2mm Wafer).

To connect SATA device:

1.Attach either end of the signal cable

to the SATA connector on

motherboard.

Attach the other end to the SATA

device.

2. Attach the SATA power cable to the

SATA device and connect the other

end

from the power supply.

VGA Wafer CONNECTOR .

24. ATX12V1. (ATX12V Power Input) 25. SYSFAN3 (System FAN connector 3).

PIN SIGNAL

GND

+12V

Fan speed data

26. CPUFAN1 (CPU FAN connector).

27. SYS_FAN2 (System FAN connector

2).

ON/OFF controlled by CPU

temperature setting of BIOS.

PIN SIGNAL

GND

+12V

Fan speed data

CPU FAN PWM

Control

PIN SIGNAL

GND

+12V

Fan speed data

AR-B5800 User Manual

28. SYS_FAN1 (System FAN connector 1). 29. JP1 (For LAN1/LAN2 Bypass Function

Select.).

PIN SIGNAL

GND

+12V

Fan speed data

Pins 1 and 2 shorted

(Default): Forced Normal.

Pins 2 and 3 shorted:

Controlled By CPLD.

Otherwise : Forced Bypass

30. RTC1 31. CCMOS1.

CMOS Backup Battery:

An onboard battery saves the CMOS memory to

keep the BIOS information stays on even after

disconnected your system with power source.

Nevertheless, this backup battery exhausts after

some five years.

Once the error message like “CMOS BATTERY

HAS FAILED” or “CMOS checksum error”

displays on monitor, this backup battery is no

longer functional and has to be renewed

32. JP4 (For LAN3/LAN4 Bypass Function

Select.).

Pins 1 and 2 shorted

(Default): Forced Normal.

Pins 2 and 3 shorted:

Controlled By CPLD.

Otherwise : Forced Bypass

AR-B5800 User Manual

3 BIos setting

This chapter describes the BIOS menu displays and explains how to perform common tasks

needed to get the system up and running. It also gives detailed explanation of the elements found

in each of the BIOS menus. The following topics are covered:

 Main Setup

 Advanced Chipset Setup

 Peripherals Setup

 PnP/PCI Setup

 PC Health Setup

 Boot Setup

 Exit Setup

AR-B5800 User Manual

3.1 Main Setup

Once you enter the Award BIOS™ CMOS Setup Utility, the Main Menu will appear on the screen.

Use the arrow keys to highlight the item and then use the <Pg Up> <Pg Dn> keys to select the

desired value in each item.

Note: The control keys are listed at the bottom of the menu. If you need any help with the item fields, you

can press the <F1> key, and the relevant information will be displayed.

Option Choice Description

Date Setup

N/A

Set the system date. Note that the ‘Day’

automatically changes when you set the

date.

Time Setup

N/A Set the system time.

IDE Channel 0

Master

N/A

The onboard CF connectors provide one

channel for connecting one CF CARD Only

the BIOS will auto-detect the CF type.

AR-B5800 User Manual

SATA Channel

1/2

N/A

The onboard SATA connectors provide 1

channel for connecting one SATA hard disks,

the BIOS will auto-detect the SATA type.

Halt On

All Errors,

No Errors,

All but keyboard.

Select the situation in which you want the

BIOS to stop the POST process and notify

you.

3.2 Advanced Chipset Setup

This section allows you to configure and improve your system and follows you to set up some

system features according to your preference.

Option Choice Description

Quick Power On Self

Test

Enabled

Disabled

This category speeds up Power On Self Test (POST) after you

have powered up the computer. If it is set to Enable, BIOS will

shorten or skip some check items during POST.

AR-B5800 User Manual

Full Screen Logo

Show

Enabled

Disabled

Select Enabled to show the OEM full screen logo if you have

add-in BIOS.

APIC Mode

Enabled

Disabled

Advanced Programmable Interrupt Controller.This item

[Enabled] for more system INTerrupts that AR-B5800

required.

Pre-allocated

Memory Size

32Mb

64Mb

128Mb

This Item is for setting the Frame Buffer (Share system memory

as display memory).

DVMT Mode

Enabled

Disabled

Dynamic Video Memory Technology.

[Enabled] for optimizing amount of memory is located for

balanced graphics and system performance.

Console Redirection

Enabled

Disabled

[Enabled] for user who w ant to remote control the system via

serial port.

Baud Rate

115200(Max)

The baud rate of remote control machine should the same as

the system for communication.

LAN Bypass

Function

Enabled

Disabled

For user Enable/Disable LAN Bypass Function !!.

3.3 PnP/PCI Setup

The option configures the PCI bus system. All PCI bus system on the system use INT#, thus all

installed PCI cards must be set to this value.

Page is loading ...

Acrosser Technology AR-R5800 User manual

Brand: Acrosser Technology

Model: AR-R5800

Category: Motherboards

Type: User manual

This manual is also suitable for

AR-B5800A

Download PDF

report

Acrosser Technology AR-R5800 User manual

This manual is also suitable for

Acrosser Technology AR-R5800 User manual

Related papers

Other documents