Atleisure UMB-015319 Assembly And User's Manual

Brand
Atleisure
Model
UMB-015319
Type
Assembly And User's Manual
Assembly and User Manual
I TEM:UMB-015319
UMB-015333
UMB-015326
M46093
The schematics in this manual are for assembly and operation illustration
only. They may differ from the umbrella’s actual appearance.
For additional product information, please contact our
Customer Service Center toll free at 1-855-880-7205
between 8am and 5pm Eastern Time, Monday through Friday.
Contact our customer service department toll free at 1-855-880-7205. Contact our customer service department toll free at 1-855-880-7205.
8. To Operate the Umbrella | | Instructions of Set-Up & Operation 5.
Fig. 7 Adjust the position of the canopy
A B
Control
knob
Rotate
NOTE: The umbrella has a unique design that moves the pole out of your
way and off to the side. The multiple position canopy can rotate 360°
around the axis of the main pole to offer the shade on your expected area
around the umbrella as shown in Fig. 7. (See Fig. 6 on page 7 for adjusting
the position of the canopy.)
NOTE: To prevent damage to the canopy DO NOT leave the umbrella open
directly facing the wind. Always take down the umbrella when not in use
and during high or gusting wind and rain.
Press the light switch to turn on/off the solar lights as shown in Fig 8, then
the solar offset umbrella is ready to enjoy.
NOTE: The umbrella has a unique design that moves the pole out of your way
and off to the side. The multiple position canopy can rotate 360°around the axis
of the main pole to offer the shade on your expected area around the umbrella as
shown in Fig. 9. (See Fig. 7 for adjusting the position of the canopy.)
ON
OFF
Light Switch
Rotates
360˚
Canopy position
adjusting
Fig.1
Fig.8
Fig.2
Fig.9
Before beginning assembly of product, make sure all parts are present.
Compare parts with package contents list. If any part is missing or damaged,
contact our customer service toll free at 1-855-880-7205 for replacement
parts or further instructions.
Estimated Assembly Time: 30 minutes
Tools Required for Assembly: Open end wrench or adjustable wrench (not included)
Step 1. Place the Upper Cross (D)
over Lower Cross Leg (C) to form
an “X” as shown in Fig. 1.
Step 2. Attach the Holder Pole (F) to
the cross legs (C&D) with the Screws
(G) and Washers (H) (found in blister
pack) as shown in Fig 2. Hand tighten
only. Adjust the Holder Pole (F) to be
sure it is positioned correctl
y on the
base. Finally tighten all bolts. Be careful
not to over tighten.
NOTE: PLEASE
REMOVE THE
PLASTIC FILM
ON THE SOLAR
PANEL. THIS
PROTECTIVE
PLASTIC FILM IS
TO PREVENT
DAMAGE
DURING
SHIPMENT.
Step 1. Insert the plug into the
socket under the solar panel as
shown in Fig. 1.
Step 2. Put the solar panel on the top of
umbrella and hide the plug and wire inside the
groove at the top of umbrella.
Then turning the solar panel
clockwise. DO
NOT over tighten.
C
GG
HH
GG
F
HH
C
Fig.2Fig .1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Atleisure UMB-015319 Assembly And User's Manual

Brand
Atleisure
Model
UMB-015319
Type
Assembly And User's Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents