Kampmann TIP, electromechanical control version Installation Plan

  • Hello! I've reviewed the installation diagrams for the KAMPMANN TIP **00 unit heater. This document provides detailed guidance on cabling and connections with different control options. I'm ready to help with any questions you might have about the information provided, including wiring, controller options, and safety measures.
  • What type of cable should be used without the * marking?
    What type of cable should be used with the * marking?
    What is the maximum wire cross-section for the unit's terminals?
TIP
01/21 EN
With ****: J-Y(ST)Y, 0.8mm, max. 100m. Lay separately from power lines.
If other types of cables are used, they must be at least equivalent.
The terminals on the unit are suitable for a maximum wire cross-section of 2.5 mm².
Any RCCBs used for motors with EC technology must be sensitive to pulsating currents (type A). It is impossible to protect personnel
when operating the unit. This is also the case with frequency inverters that have FI safety devices. When the power supply to the unit is
switched on, pulsed charging currents of the capacitors in the integrated EMC filter can cause FI safety devices to trip. A tripping current
of 300mA is recommended to ensure the highest possible operating reliability.
The electrical data need to be respected when rating the in situ mains power supply and fusing.
Observe these points in the following installation diagrams for TIP with electromechanical control:
Comply with the details on cable types and cabling with due consideration for VDE 0100.
Without *: NYM-J. The requisite number of wires, including protective conductor, is stated on the cable. Cross-sections are not stated, as
the cable length is involved in the calculation of the cross-section.
With *: J-Y(ST)Y 0.8mm, max. 100m between the speed controller and the last unit heater; provide a shield on one side when longer
than 20 m. Lay separately from power lines.
With **: Sensor connection cable 1.5mm2 e.g. J-Y(ST) Y, 4 x 2 x 0.8mm, max. 100m. Lay separately from high-voltage cables.
With ***: J-Y(ST)Y 0.8 mm, max. 100m between the speed controller and the last unit heater; provide a shield on one side when longer
than 20 m. Lay separately from power lines.
TIP
01/21 EN
Cabling of TIP (**00), actuation by speed controller type 30510
N PEL
1
2
gn/ge
gn/ge
1
2
gn/ge
1
2
1
2
gn/ge
1
2
3
W1
gn/ge
1
2
2
1
PE PE PE L N C NC NO D1 UcUb GND A+ B- SH
Ri > 49 K
gn/ge
1
2
2
1
PE PE PE L N C NC NO D1 UcUb GND A+ B- SH
Ri > 49 K
2*
W7
3
W2
2*
W3
3
W6
3
W10
2*
W11
1
2
1
2
L N CS CS + -
3
W8
2*
W9
gn/ge
1
2
gn/ge
1
2
1
2
gn/ge
3
W4
2*
W5
Speed controller, type 30510
Mains
230 V
In situ fusing.
Observe
"Electrical data"
information table.
Mains 230 V
Unit no. 1
Type 54xx56, 54xx58 and 55xx56,
terminals Ub, Uc and GND only
Jumper ex-
works
TIP EC, electromechanical TIP EC, electromechanical
Unit no. 2
1) To further units
(refer to Information for maximum
number)
In situ terminal box
Junction box Junction box Type 54xx56, 54xx58 and 55xx56,
terminals Ub, Uc and GND only
Jumper ex-
works
In situ terminal box 1)
TIP
01/21 EN
Cabling TIP (**00), activation via speed controller type 30510 with industrial thermostat type 30058/
30059
N PEL
1
2
gn/ge
3
W1
gn/ge
1
2
2
1
PE PE PE L N C NC NO D1 UcUb GND A+ B- SH
Ri > 49 K
gn/ge
1
2
2
1
PE PE PE L N C NC NO D1 UcUb GND A+ B- SH
Ri > 49 K
2*
W7
3
W2
2*
W3
3
W6
3
W12
2*
W13
1
2
1
2
L N CS CS + -
gn/ge
1
2
gn/ge
1
2
1
2
3
gn/ge
1
2
1
2
gn/ge
1
2
gn/ge
1
2
1
2
gn/ge
3
W8
2*
W9
1
2
3 2 1PE
PE LH K
3
W10
gn/ge
3
W4
2*
W5
Speed controller, type 30510
Industrial thermostat type 30058,
type 30059
Mains
230 V
In situ fusing.
Observe
"Electrical data"
information table.
Mains 230 V
Unit no. 1
Type 54xx56, 54xx58 and 55xx56,
terminals Ub, Uc and GND only
Jumper ex-
works
TIP EC, electromechanical TIP EC, electromechanical
Unit no. 2
1) To further units
(refer to Information
for maximum number)
In situ terminal box
Junction box Junction box Type 54xx56, 54xx58 and 55xx56,
terminals Ub, Uc and GND only
Jumper ex-
works
In situ terminal box 1)
Heating
Type 30058 Type 30059
TIP
01/21 EN
Cabling of TIP (**00), actuation by speed controller type 30510 with room thermostat type 30055
N PEL
1
2
gn/ge
3
W1
gn/ge
1
2
2
1
PE PE PE L N C NC NO D1 UcUb GND A+ B- SH
Ri > 49 K
gn/ge
1
2
2
1
PE PE PE L N C NC NO D1 UcUb GND A+ B- SH
Ri > 49 K
2*
W7
3
W2
2*
W3
3
W6
3
W12
2*
W13
1
2
1
2
L N CS CS + -
gn/ge
1
2
gn/ge
1
2
1
2
3
gn/ge
1
2
1
2
gn/ge
1
2
gn/ge
1
2
1
2
gn/ge
3
W8
2*
W9
1
2
3
4 2 14
N LN
4
W10
H
3
W4
2*
W5
Mains
230 V/50 Hz
Room thermostat, type
30055
In situ fusing.
Observe
"Electrical data"
information table.
Mains 230 V
Unit no. 1
Junction box
Jumper
ex-works
Heating
Type 54x56, 54xx58,
55xx56, terminals Ub, Uc
and GND only
TIP EC, electromechanical
In situ terminal box
Jumper
ex-works
Type 54x56, 54xx58,
55xx56, terminals Ub, Uc
and GND only
Junction box
Unit no. 2
TIP EC, electromechanical
1)
1) To further units
(refer to "Information" for
maximum number)
Speed controller, type 30510
In situ terminal box
TIP
01/21 EN
Cabling of TIP(**00), actuation by speed controller type 30510 with clock thermostat type 30056
N PEL
1
2
gn/ge
3
W1
gn/ge
1
2
2
1
PE PE PE L N C NC NO D1 UcUb GND A+ B- SH
Ri > 49 K
gn/ge
1
2
2
1
PE PE PE L N C NC NO D1 UcUb GND A+ B- SH
Ri > 49 K
2*
W7
3
W2
2*
W3
3
W6
3
W12
2*
W13
1
2
1
2
L N CS CS + -
1 2
1
2
2**
W11
gn/ge
1
2
gn/ge
1
2
1
2
3
gn/ge
1
2
4
1
2
gn/ge
1
2
gn/ge
1
2
1
2
gn/ge
3
W8
2*
W9
1
2
3
4
1 2 4 5 6 7
L K
8 93
H L N
5
W10
FF
1
2
3
W4
2*
W5
Speed controller, type 30510
Clock thermostat, type 30056
Mains
230 V
In situ fusing.
Observe
"Electrical data"
information table.
Mains 230 V
Unit no. 1
Type 54xx56, 54xx58 and 55xx56,
terminals Ub, Uc and GND only
Jumper ex-
works
TIP EC, electromechanical TIP EC, electromechanical
Unit no. 2
1) To further units
(refer to Information
for maximum number)
In situ terminal box
Junction box Junction box Type 54xx56, 54xx58 and 55xx56,
terminals Ub, Uc and GND only
Jumper ex-
works
In situ terminal box 1)
Room sensor,
type FL 103
Heating
See clock thermostat instruction for
further information
TIP
01/21 EN
Cabling of TIP (**00), actuation by climate controller type 30155, 2-pipe valve actuator 230 V AC,
Open/Close
N PEL
1
2
gn/ge
gn/ge
1
2
gn/ge
1
2
1
2
3
gn/ge
1
2
1
2
1
2
1
2
1
2
1 2 3 4 5 6 7 8 9 10 11 12 13 14
N N N L H K AI GND AO GND UI GND DI GND
3
1
2
COMNO
1
2
1
2
COMNO
W11
2***
W12
W10
W9
1 2
1
2
W8
42***2*2***
3
W1
1
1
2
2
gn/ge
1
2
2
1
PE PE PE L N C NC NO D1 UcUb GND A+ B- SH
Ri > 49 K
gn/ge
1
2
2
1
PE PE PE L N C NC NO D1 UcUb GND A+ B- SH
Ri > 49 K
2*
W6
3
W7
3
W2
2*
W3
3
W4
3
W5
Mains
230 V
Air conditioning
controller
type 30155
In situ fusing.
Observe
"Electrical data"
information table.
Mains 230 V
Unit no. 1
Type 54xx56, 54xx58 and 55xx56,
terminals Ub, Uc and GND only
230 V normally closed,
optional
Thermoelectric shut-off valve
Jumper ex-
works
Contact
e.g. window
Contact
e.g. heating/cooling Room sensor
- Options -
See air conditioning controller instruction for further information
TIP EC, electromechanical TIP EC, electromechanical
Unit no. 2
Thermoelectric shut-off valve
230 V normally closed,
optional
In situ terminal box
Junction box Junction box Type 54xx56, 54xx58 and 55xx56,
terminals Ub, Uc and GND only
Jumper ex-
works
TIP
01/21 EN
Cabling of TIP (**00), actuation by climate controller type 30256, 2-pipe valve actuator 230 V AC,
Open/Close
N PEL
1
2
gn/ge
gn/ge
1
2
gn/ge
1
2
1
2
3
gn/ge
1
2
3
W1
1
1
2
2
gn/ge
1
2
2
1
PE PE PE L N C NC NO D1 UcUb GND A+ B- SH
Ri > 49 K
gn/ge
1
2
2
1
PE PE PE L N C NC NO D1 UcUb GND A+ B- SH
Ri > 49 K
2*
W6
3
W7
3
W2
2*
W3
3
W4
3
W5
1
2
1
2
1
2
3
1
2
1 2
1
2
1
2
COMNO
2***
W11
W10
W9
W8
2*2***4
GNDO3N O1 O2 I1 GND I2 GND
L
Mains
230 V
Air conditioning
controller
type 30256
In situ fusing.
Observe
"Electrical data"
information table.
Mains 230 V
Unit no. 1
Type 54xx56, 54xx58 and 55xx56,
terminals Ub, Uc and GND only
230 V normally closed,
optional
Thermoelectric shut-off valve
Jumper ex-
works
Contact
e.g. heating/cooling Room sensor
- Options -
See air conditioning controller instruction for further information
TIP EC, electromechanical TIP EC, electromechanical
Unit no. 2
Thermoelectric shut-off valve
230 V normally closed,
optional
In situ terminal box
Junction box Junction box Type 54xx56, 54xx58 and 55xx56,
terminals Ub, Uc and GND only
Jumper ex-
works
TIP
01/21 EN
Cabling of TIP (**00), actuation by speed controller type 30515
N PEL
1
2
gn/ge
W12
4
3
W1
gn/ge
1
2
2
1
PE PE PE L N C NC NO D1 UcUb GND A+ B- SH
Ri > 49 K
4
3
gn/ge
1
2
2
1
PE PE PE L N C NC NO D1 UcUb GND A+ B- SH
Ri > 49 K
4
3
4*
W6
3
W7
3
W2
4*
W3
3
W4
3
W5
1
2
3
L N PE LV N PE L N PE Err Uc GND
mains valve EC-motor
gn/ge
gn/ge
1
2
gn/ge
1
2
1
2
3
gn/ge
1
2
3
1
2
gn/ge 4
W10
3*
W11
gn/ge
1
2
gn/ge
1
2
1
2
33
1
2
gn/ge
4
W8
3*
W9
COM NC NO COM NC NO
operation fault
COMNO
1
2
1- 2+
1
2
COMNO
1
2
1- 2+
1
2
24V GND DI1 DI2 GND DI3 GND I/O AI1 GND MI1 GND
en h/c err clock room sen frost
2****
W17
3
2
1
1
2
4
3
1
3
3*
1
2
3
W13
2****
2
1
W14
1
2
1
2
2****
W15
1
2
2****
W16
3
2
1
1
2
4
3
1
3
Mains
230 V
Electronic speed
controller
type 30515
In situ fusing.
Observe
"Electrical data"
information table.
Mains 230 V
Unit no. 1
Type 54xx56, 54xx58 and 55xx56,
terminals Ub, Uc and GND only
230 V normally closed,
optional
Thermoelectric shut-off valve
Jumper ex-
works
Room sensor
TIP EC, electromechanical TIP EC, electromechanical
Unit no. 2
Thermoelectric shut-off valve
230 V normally closed,
optional
In situ terminal box
Junction box Junction box Type 54xx56, 54xx58 and 55xx56,
terminals Ub, Uc and GND only
Jumper ex-
works
In situ terminal box In situ terminal box
In situ terminal box
Frost protection or
2nd Room sensor Contact cooling Contact enable
In situ evaluation
Operating message Common fault
- Options -
See electronic speed controller instruction for
further information
To further units (refer
to Information for
maximum number)
Lay wire no. 4 to
GND on the last unit.
TIP
01/21 EN
Cabling of TIP (**00), actuation by DDC/BMS, 2-pipe valve actuator 230 V AC, Open/Close
3
W1
N PEL
1
2
gn/ge
gn/ge
1
2
gn/ge
1
2
1
2
gn/ge
4*
W3
3
W4
3
W2
gn/ge
1
2
2
1
PE PE PE L N C NC NO D1 UcUb GND A+ B- SH
Ri > 49 K
4
3
4*
W6
3
W7
3
W5
gn/ge
1
2
2
1
PE PE PE L N C NC NO D1 UcUb GND A+ B- SH
Ri > 49 K
4
3
DA1 DA1
1
2
230V
AA1
0-10V
AA1
GND DI1 DI1 AA2
0-10V
AA2
GND DI2 DI2
1
2
4
3
1
2
4
3
PEPE DA2 DA2
1
2
230V
Mains
230 V
In situ fusing.
Observe
"Electrical data"
information table.
Mains 230 V
Unit no. 1
Type 54xx56, 54xx58 and 55xx56,
terminals Ub, Uc and GND only
230 V normally closed,
optional
Thermoelectric shut-off valve
Jumper ex-
works
TIP EC, electromechanical TIP EC, electromechanical
Unit no. 2
Thermoelectric shut-off valve
230 V normally closed,
optional
In situ terminal box
Junction box Junction box Type 54xx56, 54xx58 and 55xx56,
terminals Ub, Uc and GND only
Jumper ex-
works
Building automation
system
Unit 2 motor fault
Contact open = fault
Unit 1 speed
(respect unit’s internal resistance!)
2-pipe heating/cooling
2-pipe heating/cooling
Unit 2 speed
(respect unit’s internal resistance!)
Unit 1 motor fault
Contact open = fault
/