Krone Messages - Parameters Operating instructions

Enclose this document with the operating instructions of the

machine.

Supplement to operating

instructions

Document number: 150001746_02_us

Version: 22/08/2023

Precision forage harvester

Software version: D2515020104300021

Error messages, information messages and parameters

Table of contents

2

Precision forage harvester

Supplement to operating instructions 150001746_02_en

1 Information on this document ..................................................................................................3

1.1 Validity .........................................................................................................................................3

1.2 Re-ordering ..................................................................................................................................3

1.3 Applicable documents..................................................................................................................3

2 Safety ..........................................................................................................................................4

2.1 Meaning of the supplement to the operating instructions ............................................................4

3 Error messages..........................................................................................................................5

3.1 Possible error types (FMI)............................................................................................................5

3.2 Error list........................................................................................................................................6

4 Information messages...........................................................................................................239

4.1 Information list..........................................................................................................................239

5 Parameter ...............................................................................................................................263

5.1 Parameter list...........................................................................................................................263

6 Index........................................................................................................................................312

Information on this document 1

Validity 1.1

Precision forage harvester

Supplement to operating instructions 150001746_02_en 3

1 Information on this document

1.1 Validity

This document is valid for:

BX404-60 (BiG X 1180) BX404-50 (BiG X 1080)

BX404-40 (BiG X 980) BX404-30 (BiG X 880)

BX404-27 (BiG X 780) BX404-25 (BiG X 780)

BX404-20 (BiG X 780) BX404-15 (BiG X 680)

BX404-12 (BiG X 680) BX404-10 (BiG X 680)

1.2 Re-ordering

You can request a replacement document if this document became completely or partly

unusable, or if you need it in a different language. Please specify the document number shown

on the cover page in your order. Alternatively, you can download the document online from

KRONE MEDIA https://media.krone.de.

1.3 Applicable documents

To ensure that the machine is used safely and as intended, observe the following further

applicable documents.

• Operating instructions of the respective machine

2 Safety

2.1 Meaning of the supplement to the operating instructions

4

Precision forage harvester

Supplement to operating instructions 150001746_02_en

2 Safety

WARNING

Risk of injury due to non-observance of relevant safety instructions

If the relevant safety instructions are not observed, persons may be seriously injured or killed.

In order to avoid accidents, the relevant safety instructions in the operating instructions

must be read and observed.

WARNING

Risk of injury due to non-observance of safety routines

If the relevant safety routines are not observed, persons may be seriously injured or killed.

In order to avoid accidents, the safety routines in the operating instructions must be read

and observed.

INFO

Depending on the machine type, the basic safety instructions can be found in the chapter

“Safety”, “Basic Safety Instructions” or in the chapter “Safety” of the machine operating

instructions.

2.1 Meaning of the supplement to the operating instructions

The supplement to the operating instructions is an important document and a part of the

machine. It is aimed at the user and contains safety-relevant information.

If the supplement to the operating instructions is not observed, people may be seriously injured

or killed.

Read in full and observe the “Safety” chapter of the corresponding operating instructions

before using the machine for the first time,see Page3.

Before working, also read and observe the respective sections of the corresponding

operating instructions,see Page3.

Keep the supplement to the operating instructions ready to hand for the user of the machine.

Hand over the supplement to the operating instructions to subsequent users.

Error messages 3

Possible error types (FMI) 3.1

Precision forage harvester

Supplement to operating instructions 150001746_02_en 5

3 Error messages

1

2

3

5

4

EQ003-072

1 Error number 3 Error description

2 Brief description of the error 4 Selection "Hide message until restart"

5 "Close" key

Structure of an error number

The error number is structured as follows, for example:

Error "TRM-521000-19"

TRM 521000 19

Control unit SPN (Suspect Parameter

Number) = error number

FMI = type of error, see

Page5

Acknowledging error message

Press to acknowledge the error message.

ÆThe error message is no longer displayed. The error message is displayed again if the fault

occurs again.

Or: click on "Hide message until restart"(4) and press .

ÆThe error message is no longer displayed. If the malfunction occurs again, the error

message is not displayed again. The error message is displayed again only after a restart.

Eliminate the error, see Page6.

Active errors and the error history can be displayed in the "Errors" menu on the terminal.

3.1 Possible error types (FMI)

There are different types of errors which are shown under the term FMI (Failure Mode

Identification) with an appropriate code.

FMI Meaning

0 The upper limit value was greatly exceeded.

1 The lower limit value was far below the required one.

2 The data is not permitted.

3 There is an overvoltage or a short circuit to supply voltage.

3 Error messages

3.2 Error list

6

Precision forage harvester

Supplement to operating instructions 150001746_02_en

FMI Meaning

4 There is an undervoltage or a short circuit to ground.

5 A cable is broken or amperage is too low.

6 There is a short circuit to ground or amperage is too low.

7 The mechanics do not respond or the expected result was not achieved.

8 The frequency is not permitted.

9 There is an abnormal update rate.

10 There is an abnormal rate of change.

11 The error cause is unknown.

12 There is an internal error.

13 The values of the calibration are outside the value range.

14 Particular instructions are required.

15 The upper limit value has been reached.

16 The upper limit value has been exceeded.

17 The lower limit value has been reached.

18 The lower limit value has not been reached.

19 There is a CAN communication failure.

20 The data deviates upwards.

21 The data deviates downwards.

31 The condition has been fulfilled.

3.2 Error list

Overview of the control units

Abbreviation Explanation

AFC Automatic spout control

AKP Multiple keypad

ASCB Automatic counterblade acceleration sensor

CAT-A4-ECU Caterpillar motor control module

CE Central electrical system

CIO CAN IO module

CL Control lever

DRC Drive control

FM Function module

GC Grinding operation

INS Content material sensor AgriNIR

KMB KRONE engine bridge

KMC KRONE Machine Controller

KP Keypad

LC Light control unit

Error messages 3

Error list 3.2

Precision forage harvester

Supplement to operating instructions 150001746_02_en 7

Abbreviation Explanation

LMB-ECU Motor control module

LUC Lifting unit control

MOS Contents and moisture measurement

MRDT Metal and rock detection

NM Navigation module

SCS Steering column switch

TRM Terminal

>>>

2AFC [}9]

2AKP [}11]

2ASCB [}13]

2CAT-A4-ECU [}15]

2CE [}27]

2CIO 1 [}32]

2CL [}34]

2DRC [}39]

2FM1 [}47]

2FM2 [}52]

2FM3 [}57]

2FM4 [}62]

2GC [}67]

2INS [}70]

2KMB1 [}73]

2KMB2 [}80]

2KMB3 [}87]

2KMB4 [}94]

2KMB5 [}101]

2KMC [}108]

2KP1 [}144]

2KP2 [}146]

2KP4 [}148]

2LC [}150]

2LMB-ECU2 [}153]

2LMB-ECU2-Slave [}200]

2LUC [}217]

2MOS [}224]

2MRDT [}226]

2NM [}229]

2SCS [}231]

3 Error messages

3.2 Error list

8

Precision forage harvester

Supplement to operating instructions 150001746_02_en

2TRM [}233]

Error list

Software version: D2515020149500008_200,

D2515020149500008_200

Control unit: AFC

Page 1

Error number Error text Description Figure

AFC-520192-19 CAN bus - Malfunction General CAN hardware fault

AFC-520203-3 Supply voltage - Overvoltage Input voltage too high > 32V.

AFC-520203-4 Supply voltage - Undervoltage Input voltage too low < 17.5V

AFC-520203-6 Supply voltage - Overload Power consumption of the control unit

is too high > 2A

AFC-520223-16 Temperature - Upper limit value

exceeded

Temperature of the control unit is over

80°C

AFC-520301-12 Control unit - Internal Error No access to the Power Management

Chip of the ECU

AFC-520303-3 Camera system - Overvoltage Camera sensor - input voltage too

high > 32V.

AFC-520303-4 Camera system - Undervoltage Camera sensor - input voltage too low

< 12V

AFC-520303-12 Camera system - Internal Error Calibration data not retrievable

AFC-520303-16 Camera system - Upper limit value

exceeded

Camera sensor - temperature

exceeded the temperature is above

85°C

AFC-520303-22 Camera system - Cable break or

short circuit to ground

No access to camera

AFC-520304-19 CAN communication - CAN

disturbance between control units

CAN communication problem with the

KMC

AFC-520500-11 Control unit - General disturbance ErrorRecovery - restart camera driver

AFC-520501-11 Control unit - General disturbance System was restarted by the

Watchdog

AFC-520502-11 Control unit - General disturbance Wrong version of CAN matrix

Error list

Software version: D2515020073500007_300

Control unit: AKP

Page 1

Error number Error text Description Figure

AKP-3904-7 "Open header locking/upwards" key -

Key pressed when system starts