Tektronix 071-1631-04 User manual

Revision A

www.tektronix.com

071-1631-04

AFG3000 Series

Arbitrary/Function Generators

Quick Start User Manual

are protected by national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes that in

all previously published material. Specifications and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14200 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

■ In North America, call 1-800-833-9200

■ Worldwide, visit www.tektronix.com to find contacts in your area.

Warranty 16

Tektronix warrants that the product will be free from defects in materials and workmanship for a period of three (3) years from the date

of original purchase from an authorized Tektronix distributor. If the product proves defective during this warranty period, Tektronix, at its

option, either will repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the

defective product. Batteries are excluded from this warranty. Parts, modules and replacement products used by Tektronix for warranty

work may be new or reconditioned to like new performance. All replaced parts, modules and products become the property of Tektronix.

In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the warranty period

and make suitable arrangements for the performance of service. Customer shall be responsible for packaging and shipping the defective

product to the service center designated by Tektronix, shipping charges prepaid, and with a copy of customer proof of purchase.

Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Tektronix

service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any other charges for

products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate maintenance and care.

Tektronix shall not be obligated to furnish service under this warranty a) to repair damage resulting from attempts by personnel other

than Tektronix representatives to install, repair or service the product; b) to repair damage resulting from improper use or connection to

incompatible equipment; c) to repair any damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a product

that has been modified or integrated with other products when the effect of such modification or integration increases the time or difficulty

of servicing the product.

THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY OTHER WARRANTIES,

EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX' RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS

IS THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX

AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES

IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH

DAMAGES.

Table of Contents

AFG3000 Series Quick Start User Manual

i

Table of Contents

General Safety Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Environmental Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Conventions Used in this Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

Quick Tutorial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

To Generate a Sine Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Accessing Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

General Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Before Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Operating Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Standard Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Recommended Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Powering the Instrument On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

To Change Instrument Settings at Power-on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Self Test and Self Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Selecting a Local Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Protect Your Instrument from Misuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Floating Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Protect Your DUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Update Your Instrument Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connect to a Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Equivalent Output Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Overheat Protection (AFG3011 Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Getting Acquainted with Your Instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Front Panel Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Screen Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

View Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Shortcut Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Default Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Select Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Select Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Adjust Waveform Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Channel Select (dual-channel model only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Output ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Rear Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Operating Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Generate a Pulse Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Save/Recall Arbitrary Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Generate an Arbitrary Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Modify an Arbitrary Waveform (Edit Menu) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Generate Noise/DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Generate a Burst Waveform. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Sweep a Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Modulate a Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Trigger Out. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Adjusting Parameters of Two Channel Signals (dual-channel model only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Set up Load Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Table of Contents

ii AFG3000 Series Quick Start User Manual

Invert Waveform Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Add Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Add Signal (AFG3100 and AFG3200 Series) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Generating a Differential Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

External Reference Clock (Except AFG3021B and AFG3022B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Synchronous Operation (Except AFG3021B and AFG3022B). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

USB Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Utility Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Save/Recall Instrument Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Saving a Screen Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Using the Security Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

ArbExpress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Application Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Lissajous Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Measurement of Filter Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Motor Speed Control by Pulse-Width Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Carrier Null (Frequency Modulation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Electrical (except AFG3011) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Electrical (AFG3011) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Inputs/Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Instrument Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

General Safety Summary

AFG3000 Series Quick Start User Manual

iii

General Safety Summary

Review the following safety precautions to avoid injury and prevent damage to this product or any products connected to

it. To avoid potential hazards, use this product only as specified.

Only qualified personnel should perform service procedures.

To avoid Fire or Personal Injury

Use Proper Power Cord. Use only the power cord specified for this product and certified for the country of use.

Ground the Product. This product is grounded through the grounding conductor of the power cord. To avoid electric

shock, the grounding conductor must be connected to earth ground. Before making connections to the input or output ter-

minals of the product, ensure that the product is properly grounded.

Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings and markings on the product. Consult

the product manual for further rating information before making connections to the product. Do not apply a potential to any

terminal, including the common terminal, that exceeds the maximum rating of that terminal.

Power Off. The power cord provides Mains disconnect.

Do Not Operate Without Covers. Do not operate this product with covers or panels removed.

Do Not Operate With Suspected Failures. If you suspect there is damage to this product, have it inspected by qual-

ified service personnel.

Do Not Operate in Wet/Damp Conditions.

Do Not Operate in an Explosive Atmosphere.

Keep Product Surfaces Clean and Dry.

Provide Proper Ventilation.

Refer to the manual's installation instructions for details on installing the product so it has

proper ventilation.

General Safety Summary

iv AFG3000 Series Quick Start User Manual

Symbols and Terms

Terms in this Manual. These terms may appear in this manual:

Terms on the Product. These terms may appear on the product:

DANGER indicates an injury hazard immediately accessible as you read the marking.

WARNING indicates an injury hazard not immediately accessible as you read the marking.

CAUTION indicates a hazard to property including the product.

WARNING. Warning statements identify conditions or practices that could result in injury or loss of life.

CAUTION. Caution statements identify conditions or practices that could result in damage to this product or other property.

Environmental Considerations

AFG3000 Series Quick Start User Manual

v

Environmental Considerations

This section provides information about the environmental impact of the product.

Product End-of-Life Handling

Observe the following guidelines when recycling an instrument or component.

Equipment Recycling. Production of this equipment required the extraction and use of natural resources. The equip-

ment may contain substances that could be harmful to the environment or human health if improperly handled at the

product’s end of life. In order to avoid release of such substances into the environment and to reduce the use of natural

resources, we encourage you to recycle this product in an appropriate system that will ensure that most of the materials

are reused or recycled appropriately.

The symbol shown to the left indicates that this product complies with the

European Union’s requirements according to Directive 2002/96/EC on

waste electrical and electronic equipment (WEEE). For information about

recycling about options, check the Support/Service section of the

Tektronix Web site (www.tektronix.com).

Mercury Notification. This product uses an LCD backlight lamp that contains mercury. Disposal may be regulated due

to environmental considerations. Please contact your local authorities or, within the United States, the Electronics Indus-

tries Alliance (www.eiae.org) for disposal or recycling information.

Restriction of Hazardous Substances

This product has been classified as Monitoring and Control equipment, and is outside the scope of the 2002/95/EC RoHS

Directive.

Environmental Considerations

vi AFG3000 Series Quick Start User Manual

Preface

AFG3000 Series Quick Start User Manual

vii

Preface

This manual describes the installation and operation of Tektronix AFG3000 Series Arbitrary/Function Generators along

with basic operations and concepts. The following instruments are supported by this manual:

Documentation

The following table lists related documentation available for your arbitrary/function generator. The documentation is avail-

able on the Document CD and on the Tektronix Web site (www.tektronix.com/manuals).

AFG3011 AFG3021B AFG3022B AFG3101

AFG3102 AFG3251 AFG3252

Item Purpose Location

Quick Start User Manual Unpacking, Installation, Specifica-

tion, Operation, and Overviews

Built-in Help UI Help and Operation

Programmer Manual Menu Structures, User Interface,

and Programming Information

Service Manual (Optional) Self-service and Performance test

ArbExpress Software CD Waveform creation

Import waveforms from oscilloscope

or PC

?

Preface

viii AFG3000 Series Quick Start User Manual

Conventions Used in this Manual

The following icons are used throughout this manual.

The soft keys along the right side of the display are called bezel buttons in this manual. In other documents, they may also

be called option buttons or side-menu buttons.

Front panel

power

Connect

power

Network

USB

Quick Tutorial

AFG3000 Series Quick Start User Manual

1

Quick Tutorial

The quick tutorial shows beginning users how to generate a simple sine waveform. Follow these steps to get acquainted

with the basics of the instrument:

1. Turn on the arbitrary/function generator.

2. Connect the CH1 Output of the arbitrary/function generator and the oscilloscope input with a BNC cable.

3. Select a waveform.

4. Enable the signal output.

5. Observe a waveform displayed on the oscilloscope screen.

6. Use the front-panel shortcut buttons to select a waveform parameter.

7. Select Frequency as a parameter to be changed.

8. Change the frequency value using numeric keys.

9. Change the waveform parameters using the general purpose knob and the arrow keys.

For more task-oriented descriptions of basic operation, see Application Examples on page 75.

In addition to the quick tutorial for generating a sine waveform, this section describes how to access the help system of the

arbitrary/function generator.

Quick Tutorial

2 AFG3000 Series Quick Start User Manual

To Generate a Sine Waveform

The following quick tutorial describes how to generate a continuous sine waveform using Tektronix AFG3000 Series Arbi-

trary/Function Generators. Follow these steps to learn the basics of the arbitrary/function generator.

1. Connect the power cord, and then

push the front-panel power on/off

switch to turn on the arbitrary/function

generator.

2. Connect a BNC cable from the CH1

Output of arbitrary/function generator

to an oscilloscope input connector.

3. Push the front-panel Sine button, and

then push the Continuous button to

select a waveform.

4. Push the front-panel CH1 Output On

button to enable the output.

5. Use the oscilloscope auto-scaling

function to display the sine waveform

on the screen.

If the instrument outputs a default sine

waveform, you can manually set the

oscilloscope as follows:

■ 0.5 μs/div

■ 200 mV/div

6. To change the frequency, push the

front-panel Frequency/Period short-

cut button.

2

1

AFG3000 series

Oscilloscope

3

4

5

6

Quick Tutorial

AFG3000 Series Quick Start User Manual

3

Quick Tips

■ Use the front-panel shortcut buttons to quickly select a waveform parameter. See page 26 for usage of shortcut buttons.

■ You can also specify a waveform parameter by using bezel menu selection. This method does not use the front-panel

shortcut buttons.

■ When you specify a waveform parameter using the shortcut buttons or bezel menu selection, an active parameter is

displayed in green in the graph area. (See step 8 above.)

7. The Frequency/Period/Phase Menu is

displayed and Freq is selected. You

can now change the frequency value.

8. To change the frequency value, use the

keypad and Units bezel buttons.

For example, if you enter a value "2"

using the keypad, the bezel menus will

automatically change to Units.

After entering the frequency value, push

the Units bezel button or the front-panel

Enter button to complete the entry.

You can change the Amplitude, Phase,

and Offset values in the same way.

9. You can also change the frequency

value using the general purpose knob

and the arrow keys.

To increase the value, turn the knob

clockwise.

To change a specific digit, select it by

pushing the arrow keys. Then change it

by turning the knob.

7

8

9

Quick Tutorial

4 AFG3000 Series Quick Start User Manual

Accessing Help

Quick Tips

■ When you push the Help button, the instrument displays information about the last menu displayed on the screen. If

the topic uses more than one page, turn the general purpose knob to move from page to page within the topic.

■ Push the front-panel Help button, and then push the Index bezel button to display an Index page. Push the Page Up

or Page Down bezel button until you find the index page that contains the topic you want to view. Turn the general

purpose knob to highlight a help topic. Push the Show Topic button to display the topic.

■ You can select the language of the bezel menus and Help information. See page 11.

1. Push the front-panel Help button to

display the help screen.

2. Most of the help topics contain phrases

marked with <angle brackets>. These

are links to other topics. Turn the

general purpose knob to move the high-

light from one link to another.

3. Push the Show Topic bezel button to

display the topic corresponding to the

highlighted link.

4. Push the Index bezel button to display

an Index page.

5. Push the Exit bezel button or any

front-panel button to remove the Help

text from the screen and return to the

graphic or parameter display.

1

3

2

4

5

Getting Started

AFG3000 Series Quick Start User Manual

5

Getting Started

General Features

The following table and list describe the general features of AFG3000 Series Arbitrary/Function Generators.

■ Three functions integrated into one generator:

■ 10 MHz to 240 MHz Function Generator

■ 5 MHz to 120 MHz Pulse Generator

■ 14 bits Arbitrary Waveform Generator

■ Color or monochrome LCD display

■ Ground isolation

■ Synchronous operation

■ USB memory interface

■ ArbExpress

®

Software

■ Context-sensitive Help system

Model AFG3011 AFG3021B/

AFG3022B

AFG3101/AFG3102 AFG3251/AFG3252

Channel 1 1/2 1/2 1/2

Sine 10 MHz 25 MHz 100 MHz 240 MHz

Pulse 5 MHz 12.5 MHz 50 MHz 120 MHz

Memory 2 to 131,072 2 to 131,072 2 to 16,384 >16,384 to

131,072

2 to 16,384 >16,384 to

131,072

Sampling Rate 250 MS/s 250 MS/s 1 GS/s 250 MS/s 2 GS/s 250 MS/s

Amplitude 20 V

p-p

10 V

p-p

10 V

p-p

5 V

p-p

Display Color Monochrome/

Color

Color Color

Interface USB, LAN,

GPIB

USB, LAN,

GPIB

USB, LAN, GPIB USB, LAN, GPIB

Getting Started

6 AFG3000 Series Quick Start User Manual

Before Installation

Inspect the arbitrary/function generator carton for external damage. If the carton is damaged, notify the carrier.

Remove the arbitrary/function generator from its package and check that it has not been damaged in transit. Verify that the

carton contains the instrument and its standard accessories. Refer to Standard Accessories on page 7.

Operating Requirements

Environmental

Power Supply Requirements

1. Place the instrument on a cart or

bench, observing clearance require-

ments:

■ Sides: 50 mm (2 in)

■ Rear: 50 mm (2 in)

2. Before operating, ensure that the

ambient temperature is between 0 °C

to +50 °C (+32 °F to +122 °F).

CAUTION. To ensure proper cooling, keep both sides of the instrument clear of obstructions.

Output

USB

Memory

USB

Memory

AFG

3102

1GS/s

100MHz

DUAL CHANNEL

ARBITRARY/FUNCTION GENERATOR

InputOutput Output

Channel

TriggerTrigger

View

Ch2

Ch1

Run ModeFunction

Sine

Leading/TrailingDuty/Width

Sweep Burst

Edit

Utility

Save RecallMore...

Arb

Pulse

Ramp

Square

Continuous Modulation

Default

Help

Offset/Low

Frequency/Period Amplitude/High

Phase Delay

156.3 mm

329.6 mm

Source Voltage and Frequency 100 V to 240 V, 47 Hz to 63 Hz

or 115 V, 360 Hz to 440 Hz

Power Consumption Less than 120 W

Getting Started

AFG3000 Series Quick Start User Manual

7

Standard Accessories

Unpack the instrument and check that you received all items listed as Standard Accessories. Check the Tektronix Web site

(www.tektronix.com) for the most current information.

Accessory Tektronix part number

AFG3000 Series Arbitrary/Function Generators Quick Start User Manual

English (Option L0) 071-1631-xx

French (Option L1)

1

1. These manuals contain a language overlay for the front panel controls.

071-1632-xx

Italian (Option L2) 071-1669-xx

German (Option L3)

1

071-1633-xx

Spanish (Option L4) 071-1670-xx

Japanese (Option L5)

1

071-1634-xx

Simple Chinese (Option L7)

1

071-1635-xx

Traditional Chinese (Option L8)

1

071-1636-xx

Korean (Option L9)

1

071-1637-xx

Russian (Option L10)

1

071-1638-xx

No printed manual (Option L99) – – –

AFG3000 Series Document CD 063-3828-xx

ArbExpress (Application Software for Tektronix Arbitrary/ Function Generators) Software CD 063-3763-xx

AFG3000 Series Arbitrary/Function Generators Programmer Manual (a PDF file on the

AFG3000 Series Document CD)

071-1639-xx

AFG3000 Series Arbitrary/Function Generators Service Manual (a PDF file on the AFG3000

Series Document CD)

071-1640-xx

Power cord

North America (Option A0) 161-0066-00

Universal Euro (Option A1) 161-0066-09

United Kingdom (Option A2) 161-0066-10

Australia (Option A3) 161-0066-13

Switzerland (Option A5) 161-0154-00

Japan (Option A6) 161-0298-00

China (Option A10) 161-0304-00

No power cord or AC adapter (Option A99) – – –

Getting Started

8 AFG3000 Series Quick Start User Manual

Recommended Accessories

The following optional accessories are recommended for your instrument:

■ 50 Ω BNC cable, double-shielded, 91 cm (36 in) (Tektronix part number 012-0482-00)

■ 50 Ω BNC cable, double-shielded, 250 cm (98 in) (Tektronix part number 012-1256-00)

■ GPIB interface cable, double-shielded, 2 m (Tektronix part number 012-0991-00)

■ RM3100 Rackmount kit (see page 91 for dimensions of the kit)

■ Fuse adapter (see page 12 for more information)

Powering the Instrument On and Off

Power On

Power Off

NOTE. To ensure the EMC compliance listed in the Specifications, connect only high quality shielded cables to this instru-

ment. High quality shielded cables typically are braid and foil types that have low impedance connection to shielded con-

nectors at both ends.

1. Insert the AC power cord into the

power receptacle on the rear panel.

2. Use the front-panel power button to

power on the instrument.

Wait until the front panel display shows

that the instrument has passed all

power-on self tests.

1. Use the front-panel power button to

power off the instrument.

120

VA

1

Output

USB

Memory

USB

Memory

AFG

3102

1GS/s

100MHz

DUAL CHANNEL

ARBITRARY/FUNCTION GENERATOR

InputOutput Output

Channel

TriggerTrigger

View

Ch2

Ch1

Run ModeFunction

Sine

Leading/TrailingDuty/Width

Sweep Burst

Edit

Utility

Save RecallMore...

Arb

Pulse

Ramp

Square

Continuous Modulation

Default

Help

Offset/Low

Frequency/Period Amplitude/High

Phase Delay

2

Output

USB

Memory

USB

Memory

AFG

3102

1GS/s

100MHz

DUAL CHANNEL

ARBITRARY/FUNCTION GENERATOR

InputOutput Output

Channel

TriggerTrigger

View

Ch2

Ch1

Run ModeFunction

Sine

Leading/TrailingDuty/Width

Sweep Burst

Edit

Utility

Save RecallMore...

Arb

Pulse

Ramp

Square

Continuous Modulation

Default

Help

Offset/Low

Frequency/Period Amplitude/High

Phase Delay

1

Page is loading ...

Tektronix 071-1631-04 User manual

This manual is also suitable for

Tektronix 071-1631-04 User manual

Related papers

Other documents