Page is loading ...
Assembly Guide for DE896-FL
V1.0
2007/10/28
Enfocus Software - Customer Support
Enfocus Software - Customer Support
Index
1. Outlook …………..……………………………………………2
2. Open Housing ……………………………………...………...4
3. Install Key components ………………………………………7
4. Assemble the Supporter & Upper Case…………………..10
5. Appendix 1 Packing List…………………………………….15
6. Appendix 2 Table of Screw and TOQUE………………….16
7. Appendix 3 Watch Dog Timer Configuration…….………..17
8. Appendix 4 Outline and Holder Drawing .………….………22
Enfocus Software - Customer Support
11
1. Outlook
Front IO
Front USB Power ButtonFront USB Power Button
Enfocus Software - Customer Support
2
Rear IO
VGADC Power
19V
PS/2
KB
(with Y cable can support PS/2 KB & MS)
LAN USB
Audio
Kingstone
Lock
COM
Port
Antenna
Hole
VGADC Power
19V
PS/2
KB
(with Y cable can support PS/2 KB & MS)
LAN USB
Audio
Kingstone
Lock
COM
Port
Antenna
Hole
Enfocus Software - Customer Support
3
2. Open Housing
2-1 . Unscrew the upper case (2pcs of FPH M3
screws in rear side)
(Screwdriver torque : 5.0±0.2 kgf. cm )
2-2. Unscrew the upper case (2pcs of FH M3
screws in top side ).
(Screwdriver torque : 5.0±0.2 kgf. cm )
Enfocus Software - Customer Support
4
2-3. Remove the Upper case
2-4. Unscrew 3 screws from HDD supporter
(Screwdriver torque : 5.0±0.2 kgf. cm )
2-5. Remove the protection from HDD
supporter’s thermal tape
Front side
Rear side
Enfocus Software - Customer Support
5
2-6. You will see the kernel of Digital Engine
VIA C7 series CPU is nano BGA package, so the CPU already mount on MB
No need to detach the CPU Heatsink.
Enfocus Software - Customer Support
6
3. Install Key components
3-1 Insert memory module
Insert the memory module in upper slot in 30
degree angle as shown in the picture, push
down the memory module slowly till there's a
clipping sound.
Enfocus Software - Customer Support
7
3-2 . Assemble the hard disc
3-2-1. Insert the SATA hard disc into the
support with about 30 degree angle
3-2-2. Screw the hard disc on the supporter
with 4pcs of FPH M3 screws
(Screwdriver torque : 2.5±0.1 kgf. cm )
Enfocus Software - Customer Support
8
3-3. Assemble the MPI-SATA card
3-3-1. Assemble the MPI-SATA card to the
hard disc
3-3-2. Screw the MPI-SATA card on the
supporter with 2pcs M2 screws
(Screwdriver torque:0.7±0.1kgf.cm)
3-3-3. FPH M3 Screw FPH M2xL3 Screw FH M3 Screw
Enfocus Software - Customer Support
9
4. Assemble the Supporter & Upper Case
4-1. Assemble the supporter and lower case
4-1-1 Insert the MPI-SATA card into the slot on
motherboard
4-1-2Screw the supporter on the lower
case with 2pcs of FH M3 screws and 1pcs of
FPH M3 screw
(Screwdriver torque : 5.0±0.2 kgf. cm )
Enfocus Software - Customer Support
10
4-2. Connect the wires
4-2-1.Connect the power switch wire
4-2-2.Connect the front USB wires
4-2-3 Adjust the USB cable to arrange it under
the supporter
2
1
Enfocus Software - Customer Support
11
4-3. Assemble the upper case
4-3-1 Slide in the uppercase carefully.
4-3-2 Check if the upper case is rigidly
combined with lower case
4-3-3.Screw the upper case (2pcs of FPH M3
±
3-4-4 Screw the top case (2pcs of FH M3
±
screws in rear side ).
(Screwdriver torque : 5.0 0.2 kgf. cm )
screws)
(Screwdriver torque : 5.0 0.2 kgf. cm )
Enfocus Software - Customer Support
12
4-4. Assemble miniPCI Wireless LAN or TV Tuner card
4-4-1 cable and nut
A,B inside housing; C,D outside housing
4-4-2 Note the hole shape to adjust the
antenna SMA connector to insert into the
hole.
B
A
C
D
4-4-3. Insert a washer to one end of the antenna
o the wire . Attaching another washer and nut t
a
4-4-4 se the screwdriver or the long nos
pliers to fix the nut . .
(Screwdr
e
iver torque : 1.5 ±0.1 kgf. cm )
ntenna wire .
Enfocus Software - Customer Support
13
4-4-5. Align the notch and Insert the card into
the slot and make sure it be locked on the
salient of the slot .
4-4-6. Install the antenna wire with the button
of the wireless LAN or TV-tuner card
4-4-7. Arrange the wire to avoid damaging the 4-4-8
wire. According the photo.
. Caution : Arrange the wire or cable not
well. The MPI–SATA card will damage
the wire or cable .
Fool-Proof notchFool-Proof notch
Enfocus Software - Customer Support
14
Appendix 1 Packing List
1 x DE896-FL system
1 x MPI-SATA card
1 x Easy Assembly Guide
1 x Driver CD
1 x 65W Adapter and Power Cord
of M3 screw
1 x L type Holder for fanless model with 4 pcs
1 x PS2 Keyboard/Mouse cable
4 x Rubber Foot
1 x HOT Caution label
4 x M3 - L5 screws
2 x M2 - L3 screws
Enfocus Software - Customer Support
15
Appendix 2 Table of Screw and Torque
No. Screw Photo Position Q’ty Screw spec. Torque Screw driver
spec.
1
Rear side 2 FPH M3- L5 5±0. 2
kgf-cm
Phillips #2⊕
2
HDD 4 FPH M3- L5 2.5±0. 2
kgf-cm
Phill⊕
Length
ips #2
≧ 8cm
3
Supporter 1 FPH M3- L5 5±0. 2
kgf-cm
Phillips #2⊕
4
Su
cover kgf-cm
pporter, Top 3 FH M3-L5 5±0. 2 Phillips #2⊕
5
M dPI-SATA car 2 FPH M2- L3 0.7±0. 1
kgf-cm
Phillips #1⊕
Enfocus Software - Customer Support
16
Appendix 3 Watch Dog Timer Configuration
T WDT is used to g y o utput a use
programmable count. The WDT is suitable for use in the prevention
stem lock-up, such as when software becomes trapped in a deadlock.
nder these sort of circumstances, the timer will count to zero and the
lected outputs will be driven. Under normal circumstance, the user
ill restart the WDT at regular intervals before the timer counts to zero.
he enerate a variet f o signals after r
of
sy
U
se
w
Enfocus Software - Customer Support
17
CODE FLOW-CHART
1. Initial Watchdog Pin
(1)set -> Logical Device: Global
CR: 0x2D
Bit: 0 = 0 WDTO.
(2)set -> Logical Device: 0x09
CR: 0X30
Bit:3 = 1 activate GPIO5
CR: 0xE0, 0xE1, 0xE2
Bit: 6, Bit: 7, Bit: 6
= 0 GPIO port is programmed as an output port.
Sta t r
Initial Watchdog Pin
1. Stop timer
(1)set -> Logical Device: 0x08
0xF6
CR:
Bit: 7~0 = 0x0
0 Stop timer
WDTO
Bit: 4 = 0 Timer counting
(2)Set -> Logical Device 0x08
0x30
CR
Bit:0 = 1, activate
2. Clear Status
8
(1)set -> Logical Device: 0x0
CR: 0xF7
Stop T and
Clear Status
imer
Enfocus Software - Customer Support
18
/
