CTS WPC-2012 User manual

Brand: CTS

Model: WPC-2012

Category: Network media converters

Type: User manual

This manual is also suitable for

WPC-2012 Series

Trademarks

CTS is a registered trademark of Connection Technology Systems Inc.. Contents

subject to revision without prior notice. All other trademarks remain the property of their

owners.

This publication may not be reproduced as a whole or in part, in any way whatsoever

unless prior consent has been obtained from Connection Technology Systems Inc..

FCC Warning

WPC-2012 Series Media Converters have been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These

standards are designed to provide reasonable protection against harmful interference

when these devices are operated in a commercial environment. These devices generate,

use, and can radiate radio frequency energy and may cause harmful interference to

radio communications unless installed in accordance with this User’s Guide. Operation f

these devices in a residential area is likely to cause harmful interference which will make

the user responsible for the appropriate remedial action at his / her own expense.

CE Mark Warning

These are Class A products. In a domestic environment these products may cause radio

interference in which case the user will need to consider adequate preventative

methods.

1. Checklist

The WPC-2012 package should contain the following items:

WPC-2012 Converter

The Power Supply (Optional)

This User’s Guide

Please notify your sales representative immediately if any item is

missing or damaged.

2. Overview

WPC-2012 Media Converters Series support IEEE 802.3af/at

PoE feature and are specifically designed to supply power to

PoE-enabled devices such as WiFi AP or surveillance cameras.

WPC-2012 Media Converters are power supply equipments (PSE)

that can transmit data and supply power at the same time to the

powered devices (PD). The maximum cable distance that can

reach the powered devices from WPC-2012 is up to 100M,

allowing your powered devices to be installed in a place where the

power is not easily accessible.

Besides, WPC-2012 aims at industrial applications that demand a

wide range of operating temperature and require redundant power

supplies to create a reliable and stable networking environment in

the event of power failure. They can also be mounted on the wall

or onto 35mm DIN rail using DIN rail clip on the media converter.

The installation and operation procedures of WPC-2012 are

simple and straightforward. Operation status can be locally

monitored through a set of Diagnostic LED indicators on the front

panel.

Major Features:

Support Auto-Negotiation or Manual mode for TP port’s speed

& duplex configuration.

Pass through/Store and Forward Switching Mechanism

Compatible with IEEE 802.3af/at PoE+

Support MDI/MDIX Auto-Crossover

Support Link Alarm function

Support the fault alarm for the port failure

Support 1K MAC address

Support 9K bytes Jumbo Frame

Support redundant AC and DC power supply

Support a wide range of operating temperature (-20

C ~60

Support both DIN-rail and wall-mounting installation methods

Support 12K bytes packet buffer

3. Network Installation

Please follow the steps described below to complete the network

installation.



Attach a fiber cable from WPC-2012 to the fiber network.



Attach a UTP cable from the 10/100Base-TX network to

the RJ-45 port on WPC-2012.



Connect the power supply to WPC-2012 and the Power

LED will light up. The TP and F/O Link/ACT LEDs will light

up as soon as if all the cable connections are satisfactory.

4. DIP SWITCH Setting

The default setting for PIN 1 through PIN 9 is OFF.

PIN NO.

Function

OFF

TP Auto-Negotiation

Enable

Disable

Manual TP Speed

100M

10M

Manual TP Duplex

Full

Half

Link Alarm

Disable

Enable

Reserved

Always Keep OFF

Reserved

Always Keep OFF

Pass Through Mode

Disable

Enable

F/O Fault Alarm

Disable

Enable

TP Fault Alarm

Disable

Enable

NOTE:

1. Before adjusting the configuration of the DIP Switch, the

power should be unplugged.

2. Disable TP Auto-Negotiation function before configuring TP

speed/duplex manually.

5. Terminal Block

TB1 and TB2 Power Supply: Two sets of DC 48V power inputs,

TB1 and TB2, on the terminal block are offered for power

redundancy purpose. You can use both pairs of power supply

(TB1 and TB2) or use either one pair of power supply on the

terminal block and AC-DC external power supply to create the

redundant setup. The redundant power supply will take over

seamlessly when one power source is down to protect your

device or network from the loss of power. When you use only

one power supply (no redundant power is available), the LED of

PWR/Port Status will flash in orange color to alert the user.

Port Fault Alarm: One pair of port fault connection on the

terminal block is used to connect alarm devices such as

speakers or LEDs to alert users when TP or F/O port link is

disconnected. To make this function work, you must first set PIN

8 and PIN 9 on the DIP Switch to “ON” position (Enable).

6. Link Alarm

Link Alarm allows users to easily identify and diagnose the linking

status. If Link Alarm is enabled (PIN 4 is set to ON), the UTP and

fiber port can link up only when both linking conditions are good. In

addition, if the fiber or UTP port link is down during the operation,

the other port link will also be turned into the “Down” status to alert

the user. Configure Link Alarm DIP switch as “Enabled” status, it

Use flat-head

screwdriver to

loosen and tighten

the screw.

Insert positive or

negative wire as

indicated.

WPC-2012

Fig. 3 Terminal Block and DIP Switch of WPC-2012

Fig. 1 Basic Network Connection for BTFX models

Fig. 2 Basic Network Connection for WDM/SFP models

Fig. 4 Top View of

Terminal Block

provides users transparent link indication between two network

devices interconnected by WPC-2012.

If Link Alarm is disabled, the UTP and fiber port will link up based

on their individual linking condition. Furthermore, if the fiber port

link is down during the operation, the UTP port link will not be

turned into the “Down” status, and vice versa.

7. LED Description

8. Technical Specifications

Standards

IEEE 802.3, 802.3u, 802.3af/at

Interface

1 X 10/100Base-TX RJ-45 connector

1 X 100Base-FX SC/ST F/O port or SFP slot

LED

PWR, PW T1, PW T2, FDX, Speed, TP Link/ACT,

F/O Link/ACT, PoE and PWR/Port Status

Power

DC Input Voltage: 48V DC,

AC-DC Power Jack x 1,

DC Power Input x 2 on Terminal Block

Power

Consumption

36W

Shipping Weight

0.295KG

Dimensions

105mm(W)X93mm(D)X35mm(H)

Temperature

Operating: -20ºC~60ºC

Storage: -20ºC~70ºC

Humidity

5%~90% RH non-condensing

EMC Safety

FCC Part 15 Class A, CE

Media

TP:

Cat. 5 UTP cable

Fiber:

50/125, 62.5/125m multi-mode fiber

9/125m single-mode fiber

*Please contact us for further reports and updates.

9. Fiber Transceiver Information

100M Multi-Mode:

TYPE

BTFC

BTFT

Connector Type

Wavelength

1310nm

Typical Distance

2Km

Min/Max TX PWR

-20.0dBm/-14.0dBm

Sensitivity

-31.0dBm

Link Budget

11.0dB

100M Single-Mode:

TYPE

BTFC(SM-30)

BTFC(SM-50)

BTFC(SM-80)

BTFC(SM-100)

Connector Type

Wavelength

1310nm

1550nm

Typical

Distance

30Km

50Km

80Km

100Km

Min TX PWR

-15.0dBm

-5.0dBm

0dBm

-5.0dBm

Max TX PWR

-8.0dBm

0dBm

5.0dBm

0dBm

Sensitivity

-34.0dBm

-35.0dBm

-36.0dBm

-35.0dBm

Link Budget

19.0dB

30.0dB

36.0dB

30.0dB

100M Wave-Length WDM:

TYPE

W2A(SM-20)

W2B(SM-20)

W2A(SM-40)

W2B(SM-40)

Connector Type

TX Wavelength

1310nm

1550nm

1310nm

1550nm

RX Wavelength

1550nm

1310nm

1550nm

1310nm

Typical Distance

20 Km

40 Km

Min TX PWR

-14.0dBm

-8.0dBm

Max TX PWR

-8.0dBm

0dBm

Sensitivity

-31.0dBm

-34.0dBm

Link Budget

17.0 dB

26.0 dB

NOTE: Specifications may change without prior notice.

Contact Information

Connection Technology Systems INC (CTS)

18F-6, No.79, Sec.1, Xintai 5th Rd., Xizhi Dist.,

New Taipei City 221, TAIWAN, R.O.C.

TEL: +886 2 26989661 FAX: +886 2 26989662

E-Mail: info@ctsystem.com



WPC-2012 SERIES

10/100Base-TX to

100Base-FX Fast Ethernet

PoE/PSE Media Converter

User’s Guide

Version 2.0

LED

Color

Function

PWR

Green

Lit when power is available.

PW T1

Green

Lit when TB1 on Terminal Block powers up.

PW T2

Green

Lit when TB2 on Terminal Block powers up.

Link/ACT

Green

Lit when TP port link is up.

Blinking when TP port is receiving and transmitting

data.

Off when TP port link is down.

Orange

Blinking when the port link down caused by Fiber port

in case Link Alarm is enabled.

Speed

Green

Lit when TP 100M port link is up.

Off when TP 10M port link is up or no port link exists.

FDX

Green

Lit when TP port works in full-duplex mode.

Off when TP port works in half-duplex mode.

F/O

Link/ACT

Green

Lit when Fiber port link is up.

Blinking when Fiber port is receiving and transmitting

data.

Off when Fiber port link is down.

Orange

Blinking when the port link down caused by TP port in

case Link Alarm is enabled.

PWR/Port

Status

Orange

Lit when TP/Fiber port link is down and two power

sources are available, or TP/Fiber port link is down

and only one power source is available. (This

indication only works when PIN 8 and PIN 9 on the DIP

Switch are set to “Enable”.)

Blinking when the redundancy system works

abnormally (only one power source is available) and

port links work normally.

Off when two power sources are available and port

links work normally.

PoE

Green

Lit when the device is supplying the power.

Blinking when the device does not supply the power.

Rapidly blinking when the device’s PoE function works

abnormally.

CTS WPC-2012 User manual

Brand: CTS

Model: WPC-2012

Category: Network media converters

Type: User manual

This manual is also suitable for

WPC-2012 Series

Download PDF

report

CTS WPC-2012 User manual

This manual is also suitable for

CTS WPC-2012 User manual

Related papers

Other documents