ANTAIRA FCM-2312WX User manual

Brand
ANTAIRA
Model
FCM-2312WX
Category
Network media converters
Type
User manual
PN:6306X2312300XXX
Trademarks
Contents subject to revision without prior notice.
All trademarks remain the property of their respective
owners
Copyright Statement
This publication may not be reproduced as a whole or in
part, in any way whatsoever unless prior consent has been
obtained from owner.
FCC Warning
The OPTOLINX WDM MEDIA CONVERTER has been
tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules.
These standards are designed to provide reasonable
protection against harmful interference when this device
is operated in a commercial environment. This device
generate, use, and can radiate radio frequency energy
and may cause harmful interference to radio
communications unless installed in accordance with this
User’s Guide. Operation of this device in a residential
area is likely to cause harmful interference in which cases
the user is responsible for taking appropriate remedial
action at his/her own expense.
CE Mark Warning
This is class A products. In a domestic environment this
product may cause radio interference in which case the
user will need to consider adequate preventative
methods.
1. Checklist
The carton should contain following items:
OPTOLINX WDM MEDIA CONVERTER
User’s guide
Please notify your sales representative immediately if any
items are missing or damaged.
2. Overview
The OPTOLINX WDM MEDIA CONVERTER is designed
to meet the emerging network deployment needs. This
cost effective solution allows users to extend their network
distance up to 20KM via optical fiber.
In addition, the OPTOLINX WDM MEDIA CONVERTER
adopts WDM technology, enabling communication via a
single optical fiber. The OPTOLINX WDM MEDIA
CONVERTER provides the most cost effective way to
double the bandwidth of an existing fiber network.
Besides being a traditional converter, the OPTOLINX
WDM MEDIA CONVERTER also has built-in monitoring &
self-diagnostic functions to guarantee operation. These
smart monitoring functions allow users to maintain and
diagnose their critical fiber network more efficiently.
The OPTOLINX WDM MEDIA CONVERTER is fully
compliant with IEEE 802.3, 802.3u standards. Installation
and operation procedures are simple and straightforward.
Operation status and Smart Monitor may be monitored
through the LED or the Buzzer.
Feature and Benefits
-
10/100Base-TX to 100BASE-FX Converter
-
Complies with IEEE 802.3, 802.3u standards
-
Interface: 1 * RJ-45 connector
1 * SC Duplex connector
-
MDI/MDIX Auto-Crossover supported
-
Supports Remote Look Back Diagnostic
-
Supports local and remote status monitor: fiber link
status monitor and testing mode status
-
Supports Diagnostic testing
3. Installation
The installation procedure is simple and straightforward:
• Remove the Converter Chassis front panel
protective plate from the selected installation slot.
• Carefully slide the converter module into the
Converter Chassis and ensure the converter golden
finger connection with the socket, and rotate the
OPTOLINX WDM MEDIA CONVERTER bracket
screw into the Converter Chassis
• Attach fiber cable from the OPTOLINX WDM
MEDIA CONVERTER to the fiber network. The fiber
connections must be matched – transmit socket to
receive socket.
• Attach a UTP cable from the 10/100Base-TX
network to the RJ-45 port on the OPTOLINX WDM
MEDIA CONVERTER
• Check if the Power LED lights up. The TP Link and
FX Link LED will also light up when all the cable
connections are satisfactory.
Fig. 1 OPTOLINX WDM MEDIA CONVERTER Front view
10/100BASE-TX
Network
Fiber
Network
Fig. 2 Basic Network Connection
10/100BASE-TX
.
TX
FX
FDX/
COL
Status
PWR
Speed
Diag
Fiber
Transceiver
RJ-45
Connector
PN:6306X2312300XXX
4. LED Description
LED Color Function
Power
Green Lit when power is available
TX/Link
ACT
Green
Lit when TP cable connection with
remote device is good
FX/Link
ACT
Green Lit when Fiber cable connection with
remote device is good
FDX/COL
Green
Lit when TP works in Full Duplex
mode
Status
Green
Lit when Local or Remote Fiber
Link is O.K.
Blinking when testing success
Orange
Lit under below condition:
Remote/ Local FX/TX port link down
Connect device not 2312 series
Blinking when testing failure
10/100M
Green
Lit when TP link in 100M
5. Technical Specifications
Standards : IEEE 802.3, 802.3u
Interface: 1 X RJ45 connector
1 X SC Duplex connector
Diagnostic LED: Power, TX/Link ACT, FX/Link ACT
FDX/COL, Status, Speed
Power Consumption 3.5W
Shipping Weight 1LB
Dimensions: 119mm × 86mm × 25 mm(W x D x H)
Temperature : Operating: 0 ~ 50
o
C
Storage: -20 ~ 60
o
C
Humidity: 5% ~ 90% RH
Emission: EMI: FCC/CE Class A
UTP Cat. 5 UTP cable
Fiber 8.3/125, 8.7/125, 9/125 or 10/125
µ
m single-mode
6. DIP Switch
Pin 1 Off/On TP Auto-negotiation Disable/Enable
Pin 2 Off/On TP Speed 10M/100M
Pin 3 Off/On TP Duplex Half /Full
Pin 4 Off/On Flow control Disable/Enable
Pin 5 Off/On MDIX/MDI mode Force/Auto
Pin 6 Off/On MDI/MDIX
Note: Pin 5 is mutually exclusive to Pin 6, when Pin 5 is
set to OFF, Pin 6 can manually set MDI/MDIX to ON/OFF.
If Pin 5 is set to ON (auto mode) then disregard Pin 6.
Default Setting
Pin1
Pin2
Pin3
Pin4
Pin5
Pin6
On
On
On
On
On
On
Please perform Power On reset after modify the Dip
Switch setting and firmware update
FCM-2312WX
10/100Base-TX to 100Base-FX
Smart Diagnostic
WDM Converter
User’s Guide
v1.2
  • Page 1 1
  • Page 2 2

ANTAIRA FCM-2312WX User manual

Brand
ANTAIRA
Model
FCM-2312WX
Category
Network media converters
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents