BrandMotion 9002-8894 Installation guide

Type
Installation guide
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!INSTALLATION!INSTRUCTIONS!
9002-8893/9002-8894 Instructions 03/15/18.docx Page 1 of 8 JS
9002-8893/9002-8894
Jeep Wrangler Back-up camera add-on
Third Brake LED Light
Items Included in the Kit
Third Brake Light
Phillips screw (only in 902-8894)
Installation Instructions
Required Tools & Supplies
Phillips Screwdriver
Plastic Trim Removal Tool
Electrical Tape
Please read so you do not VOID the
warranty:
If the camera harness is run through the center on the
camera bracket, it will cut the camera harness. This will
void the warranty on the camera.
NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color
instructions, as well as an installation video, please visit www.brandmotion.com
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!INSTALLATION!INSTRUCTIONS!
9002-8893/9002-8894 Instructions 03/15/18.docx Page 2 of 8 JS
Remove Spare Tire
Step 1: Remove spare tire
Continue to the next step of the part number of the third brake light that you have.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!INSTALLATION!INSTRUCTIONS!
9002-8893/9002-8894 Instructions 03/15/18.docx Page 3 of 8 JS
Install: 9002-8893
Step 1: Locate and remove the two #1 Philips screws from the back-side of Camera.
Step 2: Line the mounting holes from the new brake light bracket up with the mounting holes of the Camera and
mounting bracket and reinstall the two #1 Philips screws.
Got to wiring steps next:
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!INSTALLATION!INSTRUCTIONS!
9002-8893/9002-8894 Instructions 03/15/18.docx Page 4 of 8 JS
Install: 9002-8894
Step 1: Locate and remove one #1 Philips holding Camera to bracket
Step 2: Line the mounting hole from the new brake light bracket up with the mounting hole of the Camera and mounting
bracket and reinstall the one #1 Philip screws.
Go to wiring next:
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!INSTALLATION!INSTRUCTIONS!
9002-8893/9002-8894 Instructions 03/15/18.docx Page 5 of 8 JS
Wiring
Step 1: Route cable along Camera harness and follow same route as factory 3
rd
brake light harness to factory opening in
rear door.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!INSTALLATION!INSTRUCTIONS!
9002-8893/9002-8894 Instructions 03/15/18.docx Page 6 of 8 JS
Step 2: Remove cover on inside of rear door and unplug factory 3
rd
brake light harness and Install new brake light
harness.
Step 3: Unplug factory brake harness and plugin our replacement harness
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!INSTALLATION!INSTRUCTIONS!
9002-8893/9002-8894 Instructions 03/15/18.docx Page 7 of 8 JS
Test brake light and reassemble
Step 1: After testing 3
rd
brake light. Follow your disassembly steps in reverse order.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!INSTALLATION!INSTRUCTIONS!
9002-8893/9002-8894 Instructions 03/15/18.docx Page 8 of 8 JS
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

BrandMotion 9002-8894 Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI