BrandMotion 9002-8808 Installation guide

Brand: BrandMotion

Model: 9002-8808

Type: Installation guide

INSTALLATION(INSTRUCTIONS(

9002-8808.docx Page 1 of 6 JM

Jeep Wrangler Rear Vision Camera for Smittybilt 2743 Tire Carrier

2007-2018 JK

(Kit # 9002-8808)

Items Included in the Kit

Camera Mounted to Tire Carrier Bracket

Chassis Harness (23’ length)

Power Harness

4-pin to RCA Harness

These Instructions

Required Tools & Supplies

T15 & T20 Torx Bits

7mm & 10mm Sockets

Phillips Screwdriver

Plastic Trim Removal Tool

Soldering Iron, Solder, & Heat Shrink Tubing

(RECOMMENDED) or T-taps as an alternate

splicing method

Electrical Tape

NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color

instructions, as well as an installation video, please visit www.brandmotion.com

INSTALLATION(INSTRUCTIONS(

9002-8808.docx Page 2 of 6 JM

Install

Step 1: Remove spare tire.

Step 2: Insert connector from Camera connector

through the rear gate vent behind tire carrier. Make sure

to leave about 6” of slack hanging out of the opening to

connect the camera to.

Step 3: Using a plastic trim removal tool, remove

interior panels on inside of rear gate.

Step 4: Pull harness through the rear gate openings.

Step 5: Use Wire Ties to secure Chassis Harness to

existing harness.

Step 6: Use supplied Wire Ties to secure Chassis

Harness to fabric factory wire cover. CAUTION: Leave

enough slack to allow gate to open fully.

Step 7: Use a T20 Torx bit to remove subwoofer box.

(If equipped.)

INSTALLATION(INSTRUCTIONS(

9002-8808.docx Page 3 of 6 JM

Step 8: Using a plastic trim removal tool, pry off rear

seat belt closeout.

Step 9: Using a plastic trim removal tool, remove rear

access panel to expose 10mm bolt, and remove bolt.

Step 10: Pull out subwoofer box slightly to gain access

to run Chassis Harness along existing harness

Step 11: Pull back carpet and continue running Chassis

Harness forward.

Step 12: Run Chassis Harness under B-pillar cover to

passenger doorsill. Use a plastic trim removal tool to

remove the (2) plastic push pins and remove passenger

sill plate/kick panel.

Step 13: Remove rubber bin insert from top of dash.

INSTALLATION(INSTRUCTIONS(

9002-8808.docx Page 4 of 6 JM

Step 14: Remove 7mm bolt .

Step 15: Using a plastic trim removal tool, remove

window switch panel.

Step 16: Disconnect harness from window switches.

Step 17: Remove 7mm bolt.

Step 18: Remove driver knee bolster cover.

Step 19: Remove (2) 7mm bolts on both sides of the

steering column.

Step 20: Remove center stack/cluster surround.

INSTALLATION(INSTRUCTIONS(

9002-8808.docx Page 5 of 6 JM

Step 21: Remove glove box for access and run Chassis

Harness toward center of dash.

Step 22: Using a plastic trim removal tool, remove

HVAC panel.

Step 23: Connecting Power harness.

Splice Red power wire to Blue/Red wire on back of

power point and Splice Black Ground to Black/White

wire. RECOMMENDED: Use solder and cover with heat

shrink tubing or use T-taps as an alternate connection

method.

Step 24: Connect Chassis Harness to RCA Harness.

Step 25: Plug the Chassis Harness RCA connector into

your aftermarket display.

Step 26: Reinstall your spare tire onto the tire carrier,

but do not mount with lock down bar.

Step 27: Put the supplied camera mount on to the

factory tire hold down piece.

INSTALLATION(INSTRUCTIONS(

9002-8808.docx Page 6 of 6 JM

Step 28: Mount the 2 pieces with the lock down bar to

the spare tire carrier. Run the camera wire through the

opening of the spare tire.

Step 29: Connect to 4-pin connectors together inside

the tire carrier by reaching around the spare tire.

Step 30: Make sure tire lock down bar is in the correct

location.

Step 26: Test the system. Start vehicle and shift into

Reverse in order to check that all connections were

made properly. If all of the connections are correct you

will see the camera image displayed on your aftermarket

display.

Step 27: Reassemble vehicle. Follow your disassembly

steps in reverse order, taking care not to bind the

harness wiring when reinstalling trim.

Step 31: Reassemble vehicle. Follow your disassembly

steps in reverse order, taking care not to bind the

harness wiring when reinstalling trim.

BrandMotion 9002-8808 Installation guide

BrandMotion 9002-8808 Installation guide

BrandMotion 9002-8808 Installation guide

Related papers

Other documents