PEAK SS888-FM User manual

User Manual

SS888-FM and SS888-FMK

INDEX

Chapter

Item

Page

0

Index

1

Introduction

2

I. A brief overview

2

II. Specification & Function

2

Actuator system function and control

5

I.

Actuator system overview

5

II. Actuator system connecting way

6

III. Handset function

7

3

Bed extension and folding movement

9

I. Bed extension movement

10

II. Bed folding movement

13

4

Steps in Detach of the Main Parts

20

I. Castor

20

II. Actuator

20

5

Warranty, Care & Maintenance

21

I. Warranty

21

II. Care & Maintenance

21

III. Cleaning

22

6

Troubleshooting & Spare parts

23

I. Troubleshooting

23

II. Spare parts list

25

III. Maintenance Service

29

Thank you for choosing Peak Care Homecare Bed. Before use, please:

1. Check that nothing has been damaged during shipping

2. Read this operation manual before operation

3. Keep the original packaging and if the bed doesn’t work or is

damaged on receipt, then contact the store from whom you had

purchased the bed.

PEAK CARE EQUIPMENT

3/10 TANNERY STREET UNANDERRA, NSW 2526 AUSTRALIA

Tel: +61 (2)427 22688

Fax: +61 (2)427 22699

website: http://www.peak-care.com.au

※ product complies with EN6060-1 & EN60601-2-52.

Chapter

1:

Introduction of Integrity SS888-FM

I.

1.

A brief overview

All frames are made of steel with light cream colour powder

coating.

2.

24V DC actuator systems. Voltage:230V/50Hz

3.

Head/foot board are wooden board with scratch proof

4.

Bed surfaces are made of steel board with powder coating.

5.

Two IV pole sockets & two lifting pole sockets.

II. Specification& Function

1. Overall size: L2140mmxW900/1070mmxH300-700mm

2. 24V DC actuator systems.Voltage:230V/50Hz

3. Max user weight capacity: 220kg.

4. Bed height adjustable is from 300 to 700mm

5. Back lifting angle 0-73°

6. Knee lifting angle 0-35°

7. Trendelenburg and Rev. trendelenburg angle 0-12°

8. High quality 4" braking castors.

9. Two IV pole sockets & two lifting pole sockets.

10.

Packing size: Length 100cm Width 46cm Height 146cm

11.

Folded Bed size: Length 97.5cm Width 48cm Height 130cm

A. Place bed in a horizontal position when transferring the patient to or from the

bed.

B. Do not confuse the head end and foot end of the bed when placing the patient

in the horizontal position.

C. Always raise the side rails whenever the patient is lying on the bed in the

horizontal position.

D. Make sure release pins are fully engaged before using side rails.

E. The mattress should be sufficiently wide enough to prevent any part of the

patient’s body from falling between the side rails and the mattress.

F. Do not allow the patient to sit on the bed when it is in the highest horizontal

position. Lower the bed before allowing patient to sit on the bed. Never sit

or lean on the head or foot end of bed.

G. The Trendelenburg position should only be attempted when the patient has

been secured in the bed with both side rails up.

H. Do not move the bed when use the side rail.

I. Do not jump up and down on the mattress.

J. Do not operate any bed function with any missing or damaged parts

SS888-FM Homecare Bed parts

name

Detachable head

board

Head

Motor

A

Frame

Detachable foot

board

0

<>

0

<>

0

<>

Foot

Buttock

Motor

D

Frame

.

4"Braking

castor

Chapter 2: Actuator system function and control

I.

Actuator system overview

The bed actuator system must apply to the following requirement:

A. 24V low voltage DC actuator system with CE or UL approval.

B. Low-noise and water-proof,

C. Anti-overload protection, and anti-electric leakage,

D. Back-up function (Optional accessory). When power is failure, this function

can help user to keep operating for 120 minutes.

A. Our power supply is 120V or 230V, depends on use environment. Please

check power supply firstly before using it.

B. To reduce the risk of electrical shock, please do not remove the control

box, actuator and handset without our qualified technician.

C. Lock all casters before using.

D. Keep clearance of moving parts.

E. Refer to instructions located in this manual for cleaning and maintaining.

F. Do not use abrasives to clean painted surfaces.

G. Be aware of moving, telescoping, and rotating parts when positioning

the bed. Watch for pinch points. Keep fingers, arms, legs, and objects

clear of bed when any mechanism is in motion. Make sure all persons

and objects are clear of the bed when raising or lowering the bed. Do

not place arms or head into the frame while operating.

H. Keep all objects out under the bed. Make sure there is nothing under the

bed to interfere with bed operations.

I. Move out power supply and battery before repairing.

J. Make sure the cord from the control module and the cord from the

handset are clear of casters before operating and do not allow either of

these cords to get caught in the moving members of the bed.

K. Do not operate this device if these cables and the associated parts are

cut, frayed or loosely connected.

11.

Actuator system connecting

way

7

III. Handset function

1. Bed extension and folding

To extend bed, press the Back Up button.

To fold the back of the bed, press the Back Down button.

2. Backrest

To raise the back of the bed, press the Back Up button.

To lower the back of the bed, press the Back Down button.

3. To raise the foot of the bed, press the Foot Up button.

4. To lower the foot of the bed, press the Foot Down button.

5. To tilt to the back, press the trendelenburg up button.

6. To tilt to the foot, press the trendelenburg down button.

NOTE: For this procedure, refer to the drawing.

Folding:

Press to fold the bed.

Backrest

Press to lower backrest.

Extension:

Press to extend the bed.

Backrest :

Press to lower backrest.

Press to raise kneerest.

Press to lower kneerest.

Press to raise bed height.

Press to lower bed height.

Press to trendelenburg. Press to trendelenburg.

1. Do not unplug anything when the system is broken.

2. Keep the control box in charging condition at any time to maintain

battery life.

3. Unplug the power cord before removing the actuator(s) and

handset.

4. When bed function is no action, first to check the power supply and

then see the handset is well plugged or not

5. When the control box is reacting fine (you can hear the relay clicks),

after operating the handset, but the actuator is not functioning.

Check the connection between the actuator and control box. If there

is no problem, then the actuator is malfunctioned.

6. When the control box has no reaction (you cannot hear the relay

clicks), after operating the handset, check the handset connection.

If it functions occasionally, that means the connection is bad.

7. Please align the handset cable correctly when plugging into the

control box, or it will damage the socket.

8. When unplugging the handset, do not just pull the cable itself.

Please hold the head as well, or it will break the wire.

9. Please check the power cord for loose connection and avoid

unstable power voltage to prevent the transformer and fuse from

burning down.

11. The issue with power indicator on but no reaction from the handset

is mainly caused by the breakage of socket.

9

Chapter 3: Bed extension and folding movement

I. Extension movement

FOLDING

Extension

SS-888-FM Motorized extension operation manual

1

Locked both side front castor

2

Released left side of red locking bars

3

Released right side red locking bars

4

Released both side red locking bars

5

Push button to operate the extension

movements

6

Insert both side of red locking bars

7

Set up both side of red locking bars

8

Set up both side of red locking bars

9

Push back-rest movements button

10

Back-rest lifting angle 73°

11

Push knee-rest movements button

12

Knee-rest lifting angle 35°

13

Push trendelenburg button

14

Left side of Trendelenburg angle 12°

15

Push trendelenburg button

16

Right side of Trendelenburg angle 12°

17

Push bed Hi/Lo button

18

Bed hi/lo adjustment range from

300~700 mm

SS-888-FM Motorized folding operation manual

1

Pull out both side of red locking bars

2

Pull out both side of red locking bars

3

Push button to operate the bed folding

movements

4

The bed motorized folding movements

5

Bed being folded

6

Locked both side of red safety bars

7

Locked left side of red safety bars

8

Locked right side of red safety bars

9

Portability

10

Ready for delivery

Step

Picture

Description

1

Lock the head board castor before

unfolding.

Note:

Always lock before

movement.

2

Unlock the red hanger of bed two sides.

Same in another side.

Note:

1. Please do not take

them out until the

bed is fully

unfolded.

2. Be careful not to

get your hands

trapped.

3

Press backrest down key to unfold the

bed.

Note:

Make sure the 2 red bars are unlocked.

4

Take the red bar out. Repeat for the

other side.

Note:

Make sure the

bed is fully

unfolded before

taking the red

bars out.

5

Put the red bar through the button tube.

Repeat for the other side.

Note:

Please do not operate the bed until

the red bars have been stowed in

the fixed location.

6

Lock the red bar in the fixed location.

Repeat for the other side.

Note:

Please do not operate the bed until

the red bars have been stowed in

the fixed location.

17

II. Folding movement

Extension

Step

Picture

Description

1

Lock the head board castor

before folding.

Note:

Always lock before movement.

2

Unlock the red bar from the fixed

location. Repeat for the other side.

Note:

Please do not operate the bed

until the red bars have been

stowed in the fixed location.

3

Take the red bar out from the

button tube. Repeat for the other

side.

Note:

Please do not operate the bed

until the red bars have been

stowed in the fixed location.

Page is loading ...

PEAK SS888-FM User manual

This manual is also suitable for

PEAK SS888-FM User manual

Related papers

Other documents