Quadratec QRC Side Armor Installation guide

Type
Installation guide

This manual is also suitable for

The Trusted Source
®
Quadratec®Entry Guards
For Wrangler JK Vehicles
Installation Manual: for ’07-Current Wrangler JK
Front Pair #13113.5000 and Front & Rear #13113.5001
Quadratec Entry Guard Information:
Thank you for purchasing Quadratec Entry Guards for Wrangler JK. Installation is
easy and takes about 20 minutes with no tools required. Each entry guard is marked
on the underside with its description and part number for proper placement.
KIT CONTENTS: 4 PIECE KIT FRONT & REAR FOR 4-DOOR
1. QTY 4 Alcohol Prep Pads
2. QTY 1 Driver Side Front Entry Guard #12345.5102
3. QTY 1 Passenger Side Front Entry Guard #12345.5101
4. QTY 1 Driver Side Rear Entry Guard #12345.5104
5. QTY 1 Passenger Side Rear Entry Guard #12345.5103
KIT CONTENTS: 2 PIECE KIT FOR FRONT 2 OR 4 DOOR
1. QTY 2 Alcohol Prep Pads
2. QTY 1 Driver Side Front Entry Guard #12345.5102
3. QTY 1 Passenger Side Front Entry Guard #12345.5101
READ ALL SAFETY MESSAGES AND UNDERSTAND ALL
INSTRUCTIONS BEFORE ATTEMPTING TO INSTALL THIS
PRODUCT. ALWAYS WEAR SAFETY GLASSES DURING INSTALL.
1
23
45
Q_ENTRY_GRD_13113-500X_Layout 1 2/20/14 1:44 PM Page 1
02202014134435
Before You Begin: Put on safety glasses.
Remove any existing entry guards along
with any prior entry guard adhesives.
Thoroughly clean the entire entry guard
threshold area with hot soapy water
and a clean rag. Dry off sill area with a
clean dry towel or chamois. Test fit both
front entry guards to verify the proper
location of each. Do not remove the
adhesive tape backing at this moment!
Note that each entry guard is mold
marked on the back side with its proper
location.
The Trusted Source
®
2
Entry Guard Installation
Step 1: Clean threshold contact area
with an alcohol prep pad. Remove one
alcohol prep pad from its packet and
wipe the entire contact area with the
alcohol pad to remove wax and oils on
the painted surface. This promotes ad-
hesion. Repeat for each door opening
where you will install an entry guard.
Q_ENTRY_GRD_13113-500X_Layout 1 2/20/14 2:18 PM Page 2
02202014141838
Step 2: As shown above, remove the
adhesive backing from front entry
guard. Peel the plastic tape strip back-
ing to reveal the adhesive surface.
Step 3: Install Front Entry Guards as
shown below. Warning!This adhesive
tape is very aggressive and entry guard
will not be repositionable once pressed
The Trusted Source
®
3
Entry Guard Installation
into place. Carefully note the proper
placement of the entry guard in the
photo above. Make sure the entry guard
is completely inward as shown. Use
downward pressure to engage the
adhesive tape to the threshold. Repeat
for each entry guard position on your
vehicle.
Fender Bolt
Head Pocket
Entry guard notch gap
should look like this
Q_ENTRY_GRD_13113-500X_Layout 1 2/20/14 1:44 PM Page 3
02202014134436
The Trusted Source
®
4
Entry Guard Installation
Rear Door Entry Guards:
Entry Guards for the rear doors are
shorter in length, however the installa-
tion process is the same as the fronts.
Please reference the photos at the right
for Rear Door Entry Guard position ref-
erence. Repeat the process for each
entry guard position on your vehicle.
Quadratec Exclusive
Three Year Limited Warranty:
Please see separate Warranty Card
insert for full details.
©Quadratec, Inc. 2014.
All Rights Reserved.
2.20.14 LTR Version
Part #12999.1026
Driver Side Front Entry Guard
in final installed position.
Q_ENTRY_GRD_13113-500X_Layout 1 2/20/14 2:18 PM Page 4
02202014141838
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Quadratec QRC Side Armor Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI