Quadratec Custom Fit Entry Guards Installation guide

Brand
Quadratec
Model
Custom Fit Entry Guards
Type
Installation guide
The Trusted Source
®
Quadratec®Entry Guards
For Wrangler JL Vehicles
Installation Manual: for ’18-Current Wrangler JL
Front Pair #13113.5002 and Front & Rear #13113.5003
Quadratec Entry Guard Information:
Thank you for purchasing Quadratec Entry Guards for Wrangler JL. Installation is
easy and takes about 20 minutes with no tools required. Each entry guard is marked
on the underside with its description and part number for proper placement.
13113.5003 KIT CONTENTS: 4 PIECE KIT FRONT & REAR FOR 4-DOOR
1. QTY 4 Alcohol Prep Pads
2. QTY 1 Left Front Entry Guard #12345.5106
3. QTY 1 Right Front Entry Guard #12345.5105
4. QTY 1 Left Rear Entry Guard #12345.5108
5. QTY 1 Right Rear Entry Guard #12345.5107
13113.5002 KIT CONTENTS: 2 PIECE KIT FOR FRONT 2 OR 4 DOOR
1. QTY 2 Alcohol Prep Pads
2. QTY 1 Left Front Entry Guard #12345.5106
3. QTY 1 Right Front Entry Guard #12345.5105
READ ALL SAFETY MESSAGES AND UNDERSTAND ALL
INSTRUCTIONS BEFORE ATTEMPTING TO INSTALL THIS
PRODUCT. ALWAYS WEAR SAFETY GLASSES DURING INSTALL.
1
23
45
Q_JL_ENTRY_GRD_13113-500X.qxp_Layout 1 9/26/18 3:57 PM Page 1
Before You Begin: Put on safety glasses.
Remove any existing entry guards along
with any prior entry guard adhesives.
Thoroughly clean the entire entry guard
threshold area with hot soapy water
and a clean rag. Dry off sill area with a
clean dry towel or chamois. Test fit both
front entry guards to verify the proper
location of each. Do not remove the
adhesive tape backing at this moment!
Note that each entry guard is mold
marked on the back side with its proper
location.
The Trusted Source
®
2
Entry Guard Installation
Step 1: Clean threshold contact area
with an alcohol prep pad. Remove one
alcohol prep pad from its packet and
wipe the entire contact area with the
alcohol pad to remove wax and oils on
the painted surface. This promotes ad-
hesion. Repeat for each door opening
where you will install an entry guard.
Q_JL_ENTRY_GRD_13113-500X.qxp_Layout 1 9/26/18 3:57 PM Page 2
Step 2: As shown above, remove the
adhesive backing from front entry
guard. Peel the plastic tape strip back-
ing to reveal the adhesive surface.
Step 3: Install Front Entry Guards as
shown below. Warning!This adhesive
tape is very aggressive and entry guard
will not be repositionable once pressed
The Trusted Source
®
3
Entry Guard Installation
into place. Carefully note the proper
placement of the entry guard in the
photo above. Make sure the entry guard
is completely inward as shown. Use
downward pressure to engage the
adhesive tape to the threshold. Repeat
for each entry guard position on your
vehicle.
Fender Bolt
Head Pocket
3.5”From Body
Seam to Edge
Q_JL_ENTRY_GRD_13113-500X.qxp_Layout 1 9/26/18 3:57 PM Page 3
The Trusted Source
®
4
Entry Guard Installation
Rear Door Entry Guards:
Entry Guards for the rear doors are
shorter in length, however the installa-
tion process is the same as the fronts.
Please reference the photos at the right
for Rear Door Entry Guard position
reference. Repeat the process for each
entry guard position on your vehicle.
Quadratec Exclusive
Three Year Limited Warranty:
Please see separate Warranty Card
insert for full details.
©Quadratec, Inc. 2018.
All Rights Reserved.
9.26.18 LTR Version
Part #12999.3111
Driver Side (Front Left) Entry Guard
in final installed position.
2”From Body
Seam to Edge
Q_JL_ENTRY_GRD_13113-500X.qxp_Layout 1 9/26/18 3:57 PM Page 4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Quadratec Custom Fit Entry Guards Installation guide

Brand
Quadratec
Model
Custom Fit Entry Guards
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents